2008 GEELY CK maintenance

164Section 2 Charging System
(MR479Q, MR479QA, MR481QA)I. BATTERYMaintenance-free battery is applied in this vehicle. Its termination voltage is 12V. It is connected inline by six
2V single cell in tandem with walls between every pole.
1. BATTERY WARNING SIGNS
1 -- Danger of corrosion
The battery electrolyte is very corrosive. DO NOT overturn the battery.
2 -- Read the instructions for battery
3 -- Children are forbidden to touch the battery
4 -- Avoid fire, electromagnetic wave and strong light.
Avoid electric spark while repair; avoid short.
5 -- Wear protecting glasses
6 -- Danger of explosion
The explosive mixed gas will be produced while charging.
7 -- How to deal with a scrapped battery
The scrapped battery should be delivered to the collection station.1234567

223tion Problems".
5. COMPACT DISC PLAYER
Compact Disc Players (hereinafter referred as CD) use a laser beam pick--up to read the digital signals
recorded on the CD and reproduce analog signals of the music, etc.
HINT:
Never attempt to disassemble or oil any part of the player unit.
Do not insert any object other than a disc into the disc box.
NOTICE:
CD players use an invisible laser beam which could cause hazardous radiation exposure. Be sure
to operate the player correctly as instructed.
6. MAINTENANCE
(1) Tape player/magnet head cleaning:
1Raise the cassette door with your finger.
Next, using a pencil or similar object, push in
the guide.
2Using a cleaning pen or cotton applicator soaked
in cleaner, clean the magnet head surface, pinch
rollers and tape press wheel.
(2) CD player/disc cleaning:
If the disc gets dirty, clean the disc by wiping the surface
from the center to outside in the radial directions with a
soft cloth.
NOTICE:
Do not use a conventional record cleaner or anti--
static preservative.ExampleMagnet HeadTape Press WheelPinch Roller

2454. Trouble Identification
(1) Trouble Record (DTC storage)
When the circular diagnostic tests are involved in identification of a trouble, the SRS ECU (HAE2.5) will
store relevant codes, first/last diagnosis time and frequency of the trouble in EEPROM.
ySRS ECU (HAE2.5) can store up to 6 troubles, low voltage trouble as well as two crash records (front
and side).
yThe transmit of the DTCs are carried out in the way that the SRS ECU£¨HAE2.5£©via serial data
interface of the maintenance procedures assign the codes to the diagnostic detector.No. Trouble De scription Trouble shooting
1Ignition c irc uit 1 (drive r a irba g), high re sista nc e or ope n
circui
tYes
2Ignition circuit 1 (driver airbag), low resistance or short
circuitYes
3 Ignition circuit 1 (driver airbag), groundYes
4Ignition c irc uit 1 (drive r a irba g), connec te d to power
sourc eYes
5Ignition circuit 2 (passenger airbag), high resistance or
ope n c irc ui
tYes
6Ignition circuit 2 (passenger airbag), low resistance or
short c ircuitYes
7 Ignition circuit 2 (passenger airbag), groundYes
8Ignition circuit 2 (passenger airbag), connected to power
sourc eYes
9Ignition c irc uit 3 (drive r se a t belt pre tensione r), high
re sista nc e or ope n c irc uitYes
10Ignition c irc uit 3 (drive r se a t belt pre tensione r), low
resistance or short circui
tYes
11 Ignition c irc uit 3 (drive r se a t belt pre tensione r), groundYes
12Ignition c irc uit 3 (drive r se a t belt pre tensione r),
connec te d to power sourc eYes
13Ignition circuit 4 (passenger seat belt pretensioner), high
re sista nc e or ope n c irc uitYes
14Ignition circuit 4 (passenger seat belt pretensioner), low
resistance or short circui
tYes
15Ignition circuit 4 (passenger seat belt pretensioner),
groun
dYes
16Ignition circuit 4 (passenger seat belt pretensioner),
connec te d to power sourc eYes
17 High volta ge of powe r source Ye s
18 Low voltage of powe r sourc e Ye s
19Wa rning light trouble -c onne c te d to powe r sourc e or
short c ircuit of the light bulbYes
20 Wa rning light trouble -ground or fila me nt ope n c ircuit Ye s
21 Missing/mista ke of the algorithm parame te rs
No (replace SRS ECU (HAE2.5))
22 Previous crash recorde
dNo (replace SRS ECU (HAE2.5)) DTCs as re c ognize d by SRS ECU (HAE2.5)

246 The transmit of the DTCs are carried out in the way that the SRS ECU (HAE2.5) via serial data interface
of the maintenance procedures assign the codes to the diagnostic detector.23 C ommunication trouble Y e s
24 Inte rna l trouble (se e the follow ing ta ble )No (replace SRS ECU (HAE2.5))
25PADS （
passenger airbag deactivation
sw itch）
, connected to power source or open
circuitYes
26PADS （
passenger airbag deactivation
sw itch）
, ground or short c irc uitYes
27 PADS (passenger airbag switch), trouble Yes
28 C ra sh output pin, ground Y e s
29C ra sh output pin, short c irc uite d to pow e r
sourceYes
30PADI (passenger airbag deactivation switch
indic ator light) error, c onnected to pow er source
or light bulb short c irc uitYes
31PADI (passenger airbag deactivation switch
indic a tor light) e rror, ground or ope n c irc uitYes
32 Se a t be lt pre te nsione r se pa ra te ignition Y e s, up to 5 time s
33Se a t be lt pre te nsione r se pa ra te ignition for 6
time sNo (replace SRS ECU (HAE2.5))No. Trouble De sc ription DTC
1 Ignition c irc uit 1 (drive r a irba g), high re sistanc e or ope n circ uit B1 346
2 Ignition c irc uit 1 (drive r a irba g), low re sista nc e or short c irc uit B1 347
3 Ignition c irc uit 1 (drive r a irba g), groundB1 348
4 Ignition c irc uit 1 (drive r a irba g), c onne cte d to powe r sourc e B1 349
5 Ignition c irc uit 2 (pa sse nge r a irbag), high re sista nc e or ope n c ircuit B1 352
6 Ignition c irc uit 2 (pa sse nge r a irbag), low resista nce or short c irc uit B1 353
7 Ignition c irc uit 2 (pa sse nge r a irbag), groundB1 354
8 Ignition circuit 2 (passenger airbag), connected to power source B1 355
9 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), high re sista nc e or ope n c ircuit B1 361
10 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), low resista nce or short c irc uit B1 362
11 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), ground B1 363
12 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), c onne c t to power sourc e B1 364
13Ignition c ircuit 4 (passe nger se a t be lt pre tensione r), high re sista nc e or open
circuitB1 367 Diagnostic DTCs

259III. DIAGNOSIS OF CRASHED VEHICLEsWhether the SRS is deployed or not, the checking and maintenance of the crashed vehicle shall be carried
out according to the following procedures.
1. Check the diagnostic signal of ECU
(1) Connect the check connector of the Hi-DS T Scan Meter.
(2) Read out the diagnostic results from Hi-DS T Scan Meter.
2. Repair procedures
(1) When the SRS is deployed, the following parts shall be renewed.
1Passenger airbag assembly.
2ECU.
3Driver airbag assembly.
Check the following parts, if abnormal, replace with new ones.
1Clock spring.
2Steering wheel, steering column and steering lower shaft
component.
The installation status of driver airbag assembly in relation to steering wheel.
1Check and see if there is abnormal noise in the steering wheel, the action of the same is good,
or the clearance is normal.
2Check the union joint of the wire harness for damage and the terminal for distortion.
3. ECU
(1) Check the brackets of the ECU Case for recess, crack, distortion, etc.
(2) Check the union joint for damage and terminal for distortion.
(3) Check the installation status of he ECU brackets
1Check the hood for recess, crack, distortion, etc.
2Check the union joint for damage, terminal for distortion
and wire harness for seizure.
3Check the case of the gas generator for recess,
crack and distortion.NOTICE
Due to shock, when the battery power
supply is insufficient, the scan Meter
cannot communicate with ECU, the
instrument panel wire harness shall be
checked and maintained or external
power source shall be used.