2008 GEELY CK warning light

275VIII. ABS ECU Connector Pin LayoutABS ECU Connector (End Views)
Electrical Wiring DiagramCombination MeterABS Warning Light
Drive ModuleABS ECU
ABS RR Wheel Sensor
ABS LR Wheel Sensor ABS RF Wheel Sensor
ABS LF Wheel Sensor
Brake Lamp Switch

283II. Non-DTC Problem Inspection Table1 With ignition s witch ON (Engine Off),
the AB S warning lig ht do e s no t g o o nLike ly Caus e s[De s cription] ABS Wa rning Light doe s not go
on, the like ly c a use ma y be the ope n in the
warning light powe r supply c irc uit, burne d bulb
or dama ged wa rning light drive module .z Burned fuse
z A B S W a r ning L ight B ulb bur ne d
z Power supply circuit open
z ABS Wa rning Light Drive Module da mage dCheck the ABS warning light
fuse in the fuse blockRemove the ECU connector,
does the warning light goes on
with the ignition switch ON? Check whether the ABS
warning light is burnedCheck whether the warn-
ing light power supply cir-
cuit and ground circuit in the
wire harness is openCheck the connector of the
warning light power supply
circuit and ground circuit in
the wire harness Does the fault reoccur?Abn.
Replace
Repair the wire harnessNo
Ye s
Abn.
Abn. Ok
Ye s No
Ok
OkReplace
Repair the wire
harness
Repair the connectorCheck whether the wire in the
ABS wire harness connecting
the ABS warning light drive
module and the ECU is short
to ground Ye s Replace the warning light
drive module Ye sNoRefer to "Occa-
sional Problem
Service Key Points"

284Note: This fault only applies to the condition that the system can communicate with the scan
meter (ABS ECU Power supply is normal), and there is no DTC set. 2 Afte r the e ngine is s tarte d, AB S
Warning Light is normally onLik e ly Caus e s
[De s cription]
One of the Likely Ca use s is tha t
ABS warning light drive module is da mage d or
there is a n ope n in the ABS wa rning light
circuit.z The warning light drive module is da mage d
z A B S w a r ning light dr ive module c ir c uit ope n
z ABS ECU is damagedRepair the wire harnessCheck whether there is an open circuit in the wire be-
tween the ECU and ABS warning light drive module Check the ABS warning light drive moduleReplace Abn. No Ye s Replace the ABS ECUOk

289III. ABS System CheckIte mIgnition
Switch ShiftTe rminal Pole Standard Unit
Battery Voltage OFF 25-8 10.1～
14.5 V
Battery Voltage
（
s ole noid va lve）OFF 9-24 10.1～
14.5 V
P owe r supply
in s ula t ionOFF 8-4 0.00～
0.5 V
Ground insula tion OFF 8-24 0.00～
0.5 V
P owe r supply
volta geON 8-4 10.1～
14.5 V
OFF Warning light goe s off Visua l inspec tion
ON Wa rning light goes on Visua l inspec tion
OFF Warning light goe s off Visua l inspec tion
ONWa rning light goes on
for a bout 1.7 se c onds
then goes offVisual inspection
B r a ke light s w it c h
peda l not de presse dON 8-18 0. 0～
0.5 V
B r a ke light s w it c h
peda l de pre sse dON 8-18 10. 0～
14.5 V
Diagnostic interface OFFDia gnostic inte rfa c e
K & 70.0～
0.5Ω
LF Wheel Speed
Sensor ResistanceOFF 1-20 1.2～
1.3 KΩ
RF Wheel Speed
Sensor ResistanceOFF 19-20 1.2～
1.3 KΩ
LR Wheel Speed
Sensor ResistanceOFF 5-6 1.0～
1.3 KΩ
RR Wheel Speed
Sensor ResistanceOFF 22-23 1.0～
1.3 KΩ
LF Whe e l Se nsor
Output VoltageOFF 1-2 3.4～
14.8 MV/Hz
RF Whe e l Se nsor
Output VoltageOFF 19-20 3.4～
14.8 MV/Hz
LR Whe e l Se nsor
Output VoltageOFF 5-6 >12.2 MV/Hz
RR Wheel Sensor
Output VoltageOFF 22-23 >12.2 MV/Hz
Spee d Se nsor Output
Voltage RatioABS Warning LightECU not connected
Connect ECUMaximum peak voltage
Minimum peak voltage≦2

295V. ABS Assembly ReinstallationNote: the plug of the ABS assembly hydraulic outlet can only be removed after the brake pipe is
installed, lest the foreign object will enter the brake system.1. Install the ABS assembly to the bracket, tighten the torque: 20+4Nm.
2. Remove the plug of the hydraulic outlet, installed the brake pipe. Make sure that the brake pipe is
correctly installed.
3. Install the brake pipe connected to the master cylinder.
4. The brake pipe torque is 12+4Nm (M10 x 1) and 15+3Nm (M12 x 1).
5. Fill the new brake fluid into the reservoir until the liquid level reach the MAX and bleed it as specified.
6. With the ignition switch ON, ABS Warning Light must goes on for 1.7 seconds then goes off.
7. Clear the DTC memory, check if there is DTC again.
8. Drive the vehicle to confirm the ABS function (you must feel that the pedal rebound).VI. ECU ProgramNote: when replacing the HECU or ECU, you shall program the new ECU, otherwise the ABS
Warning Light flashes and the system can not operate normally.Use the scan meter to program the ECU based on the following procedure:Connect the scan meter with the diagnostic interfaceSelect function 07, Press OK button to confirmEnter code 01901 and Press OK button to confirmSelect function 07, Press OK button to confirm, quit the diagnosticEnd

337(8) Make sure the warning light of the airbag system on for 6s and off.
If the warning light of the airbag system is not as specified, it means system fault. Check with the OBD (on-
board diagnostics).4.Rear Seat Belt Removal / InstallationWarning
Do not remove retractor.
(1) Fold rear seat back.
(2) Remove B pillar upper inside trim.
(3) Remove rear trunk partition.
(4) Remove bolt.
(5) Remove rear seat belt.
(6) The installation is in the reverse order of the removal.
5.Rear Seat Belt Buckle Removal / Installation
(1) Remove rear seat cushion.
(2) Remove the bolt.
(3) Remove rear seat belt buckle.
(4) The installation is in the reverse order of the removal.
6. Seat Belt Inspection
(1) Ensure correct installation of seat belt.
(2) Check the metal component of the seat belt for damage.
(3) If the vehicle has been vibrated during the accident, pull out the
seat belt from the retractor, observe by eye and touch the seat
belt with hand to ensure that there is no scratch (load limit retractor
does not operate).
zReplace the seat belt if it is not as specified in the technical specification.Seat BeltPullAnchorNickanchorage