2008 Citroen C CROSSER DAG ECU

6
FAMILIARISATION
Opening

 After unlocking the vehicle using the
remote control or the key, press the
handle A and raise the tailgate.
Tailgate Lower tailgate
Opening

 Push the handle C to the right and
tilt the tailgate D gently.
The maximum authorised
weight on the lower tailgate
when open is 200 kg . Spare wheel and tools
Access to the spare wheel

 Remove the plastic cover E to gain
access to the spare wheel fi xing
system.

 80
OPENING

 80  124
Closing

 Pull the handle B downwards. Closing

 Raise the tailgate D , push it to close
it, then check that it is secured
correctly. Access to the tools
The tools are stored in the storage
compartment
F in the boot right-hand
trim.

17
FAMILIARISATION
KEEPING YOUR PASSENGERS SAFE
Front passenger air bag Child lock

1. Insertion of the key.

2. Selection of the “OFF” position.

3. Removal of the key. This prevents opening of the door con-
cerned from the inside.
Lower or raise the control
A to lock or
unlock.

 106

 98 Isofix mounting
Two rings
A , located between the seat
back and seat cushion of the vehicle’s
seat, permit the securing of a child
seat.
A ring B permits securing of the upper
strap referred to as the TOP TETHER .

 95

C O M F O R T
II
48
FRONT SEATS
Manual mode
Forwards-backwards adjustment
Raise the control bar and slide the seat
forwards or backwards.
When your seat is at the correct dis-
tance, move it forwards and backwards
slightly without using the control bar to
check that it is secured correctly. Driver’s seat cushion height and
angle adjustment
Pull and/or push the control several
times to adjust the height of the seat.
Seat back angle adjustment
Pull the control upwards to adjust the
seat back.
When the seat back is at the correct
angle, release the control.
To prevent the seat back from
moving forward sharply and
knocking you, press on it with
your back or push it with your
hand while operating the lever.
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to your optimum driving
and comfort position.

C O M F O R T
II
51
REAR SEATS (ROW 2)
Seat back angle adjustment
Pull the control and adjust.
When the seat back is at the correct
angle, release the control.
Sit in the centre of the rear bench seat
to check that the two seats are at the
same level and that the angle of their
seat backs is the same.
Forwards-backwards adjustment
Pull the control towards the outside and
adjust.
When your seat is at the correct
distance, release the control.
To ensure that the seat is secured
correctly, move it forwards and
backwards slightly without using the
control. When manoeuvring the seats,
ensure that no person or ob-
ject is in the vicinity of the mov-
ing parts to avoid any risk of injury or
damage.
To prevent the seat back from mov-
ing forwards sharply and knocking
you, press on it with your back or
push it with your hand while operat-
ing the lever.
The rear seats can be folded in two
parts (1/3 - 2/3).

C O M F O R T
II
53
Folding the second row

1. Raise the rear seat lever A , or
Pull the button in the boot B for at least one second, or
Pull the rear seat releasing strap C towards you.

2. The seat backs fold forwards then the cushion rises and folds fo rwards.

3. After carrying out these operations, press on the seat lightly to check that it is secured correctly.
Before folding the seats, lower the head restraints fully.
Before folding the seat backs forwards, insert the seat belt b
uckles in the slots provided for this purpose in the rear seat
cushion.

Before folding the seats , ensure that no object or person is hindering the execution of the operatio ns.
Do not place luggage on the folded seats.

C O M F O R T
II
54
Returning the second row to the normal position

1. Lower the seat pulling simultane-
ously on the releasing strap
A lo-
cated at the rear of the cushion and
supporting the seat with your hand.
Force may be necessary to carry out these operations.
On vehicles fi tted with a third row, the rear of the cushio n of the second row is fi tted with a low light B .
When the releasing strap is pulled, the light comes on for approximately 10 seconds to light the fl oor at the base of t he
third row.
2. Press on the cushion to put it in
place until it engages.
3. Pull the seat back upright pulling si-
multaneously on the releasing strap
located at the rear of the seat back.

4. After putting the seat back back in
place, push the seat and the seat
back lightly to ensure that they are
secured correctly.

C O M F O R T
II
70
12 volt socket (120 W max)
This operates when the ignition switch
is in the “ON” or “ACC” position.
Lift the cover to gain access to the
socket. Check that the electrical equip-
ment operates with 12 volts
and that its maximum electri-
cal power is 120 W.
The prolonged use of electri-
cal equipment without running the
engine may discharge the battery. Stowing rings
There are four stowing rings in the boot
for securing luggage:
- two rings are located on the boot
fl oor,
- two rings are located on the rear side pillars.
* On 5-seat version only.
Raise the boot fl oor to gain access to
this compartment.
Right-hand side enclosed storage
compartment
This storage compartment contains the
tools for changing a wheel. Storage compartment in the fl oor *

C O M F O R T
II
71
Load space cover
Unroll the load space cover and install it
in the securing groove A .
To store the load space cover, release
it from the securing groove, it rolls up to
its initial position. Second installation position.
The load space cover can be secured
in two different positions
B , so that the
row 2 seat backs can be tilted.

1. Roll up the load space cover.

2. Move one of the slides C towards
the inside of the vehicle and insert
the tab D in the installation hole to
be used.
Move the opposite slide in the same
way.

3. After changing the position, check
that the load space cover is secured
correctly. Removing the load space cover.

1. Roll up the load space cover.

2. Move one of the slides C towards the
inside of the vehicle and raise it.
Release the opposite slide in the
same way.
To put the load space cover in place,
carry out the operations in reverse
order.
Take care not to place heavy
objects on the load space cover
when it is unfolded.
The load space cover can be stored
along the lower tailgate, unless audio
equipment is present.