2008 Citroen C CROSSER DAG ECO mode

18
FAMILIARISATION
Cruise control
This maintains a constant vehicle speed
programmed by the driver.

1.
“ON/OFF” button: activation /
deactivation of the cruise control
mode.

2.
“COAST SET” button: storing of a
driving speed then decreasing of
the cruising speed.

3.
“ACC RES” button: increasing of
the cruising speed and recalling of
the stored speed.

4.
“CANCEL” button: switching off of
the cruise control.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h) with at least second
gear engaged. This detects any obstacle (person, ve-
hicle, tree, gate,...) located behind the
vehicle.
The vehicle is fi tted with four sensors:

D. two side sensors.

E. two central sensors.
Audible rear parking assistance

 114  116
DRIVING SAFELY
Four wheel drive system
Three transmission modes are avail-
able and can be selected manually by
the driver in accordance with his re-
quirements:

A. Two wheel drive (2WD),

B. Four wheel drive (4WD AUTO),

C. Four wheel drive (4WD LOCK),

 112
Also...
You can change transmission mode
when stationary or when driving at a
speed below 60 mph (100 km/h).

I N S T R U M E N T S a n d C O N T R O L S
I
19

1. Speedometer.

2. Left-hand direction indicator and
hazard warning lights indicator
light.

3. Main beam headlamps indicator
light.

4. Diesel pre-heating indicator light.

5. Side lights indicator light.

6. Front fog lamps indicator light.

7. Seat belt not fastened / unfastened
warning light.
DIESEL MANUAL GEARBOX INSTRUMENT PANEL

18. Instrument panel display:
- Warning and status displays.
- Total and trip distance recorders.
- Service indicator.
- Coolant temperature.
- Displaying of the trip computer information.
- Cruise control reference value.
- Fascia lighting and parameter settings.
- Fuel level.
- Exterior temperature.
- Transmission mode.

8. Rear fog lamps indicator light.

9. Anti-lock braking system (ABS)
warning light.

10. Battery charge fault warning light.

11. Handbrake applied and brake fl uid
level warning light.

12. Cruise control mode indicator light.

13. Air bags warning light.

14. Engine management warning light.

15. Indicator light for right-hand
direction indicator,
Hazard warning lights indicator
light.

16. Rev counter.

17. Fascia lighting rheostat.
Panel grouping together the dials and
warning/indicator lights. These inform
the driver of the activation of a system
(operation or deactivation indicator
lights) or of the occurrence of a fault
(warning lights).

I N S T R U M E N T S a n d C O N T R O L S
I
28
Prevention messages
Information messages (ignition at “ON”)

Message is on Status of the system
2WD two wheel
drive system Flashing When the “2WD” (2 wheel drive) mode is selected using the
transmission mode selector.
4WD four wheel
drive system Flashing When the “4WD” (4 wheel drive) mode is selected using the
transmission mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system Flashing When the “LOCK” (4 wheel drive) mode is selected using the
transmission mode selector.
Dynamic stability
control system (ASC) Fixed
When the dynamic stability control system (ASC) is active.
Exterior
temperature Fixed This indicates the exterior temperature.
When the vehicle is stationary or if the speed is below 12 mp
h
(20 km/h) the temperature displayed may not correspond to the
exterior temperature.

Display is on Cause Solution - action Observations
Service
indicator Fixed Informs the driver of
the time remaining
before the vehicle’s
scheduled service. Consult a
CITROËN dealer.
This is displayed for a few
seconds when the ignition is
switched on.
Break
advised Fixed Informs the driver that
he should stop to take
a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard every
5 minutes until the vehicle stops.

I N S T R U M E N T S a n d C O N T R O L S
I
32
System which provides current
information about the route travelled.
TRIP COMPUTER Average
consumption
(l/100km or km/l or
mpg)
This is the average
quantity of fuel consumed
since the last zero reset.
This fi gure may increase following a
change in the style of driving or the
relief resulting in a reduction in the
current consumption. Average speed
(km/h or mph)
This is the average
speed calculated since
the last zero reset. Resetting the information to
zero
Automatic
If the ignition remains in the “ACC”

(Accessories) position for at least
4 hours, the average consumption value
is reset to zero automatically.
If dashes “---” are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer. Current
consumption
(l/100km or km/l or
mpg)
This is the average
quantity of fuel
consumed during the
last few seconds of
driving.
Data displays
With the ignition on, press the
INFO
button on the fascia, to the left of the
instrument panel, several times in
succession to display the different
information:
- the average consumption,
- the average speed,
- the current consumption. When the required information is
displayed, press the
INFO button for
more than two seconds.
When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.

I N S T R U M E N T S a n d C O N T R O L S
I
33

When the vehicle is
stationary , it allows
the user to change the
following parameters:
- the choice of the reini- tialisation of the aver-
age consumption and
average speed,
- the fuel consumption unit,
- the temperature display unit,
- the display language,
- activation/deactivation of the INFO
button sound,
- the break (rest) reminder display in- terval,
- restore the manufacturer’s param- eters.
FUNCTION PARAMETERS
System which provides access to
certain function parameters.
In order to change the settings,
it is essential that you stop
the vehicle and switch on the
ignition.
Apply the handbrake and place the
gear lever in neutral.

When the vehicle is moving ,
the functions setting display is not
displayed when you press the INFO
button.

With the ignition on , press the INFO
button on the fascia, to the left of the
instrument panel, several times in
succession until the “SETTING MENU”
screen is displayed. Operation

 press and hold the INFO button for
a few seconds to display the menus
screen. Press and hold the
INFO button
for a few seconds to return to the
previous screen.
When the menus screen is displayed,
if no operation is carried out within
15 seconds, the function parameters
screen is displayed.

 on the menus screen, press the

INFO button to select a function
from the list:

MENU 1/2 :
- 1 - 2 (choice of the reinitialisation of
the average consumption and aver-
age speed),
- UNIT (choice of the fuel consump-
tion units),
- choice of the temperature display
unit ,
- LANGUAGE (choice of the display
language),

MENU 2/2:
- a/b (choice of displaying a different
language on the instrument panel
display and the navigation display),
- activation / deactivation of the
INFO
button sound ,
- ALERT (changing of the “BREAK
ADVISED” break reminder display
interval),
- REINITIALISE (restore the manu-
facturer’s parameters). Choice of the reinitialisation of
the average consumption and
average speed
You can choose between two average
consumption and average speed
reinitialisation modes:
- automatic reinitialisation
( choice 1) ,
- manual reinitialisation (choice 2) .
On the menus screen:

 press the INFO button to select:

 press and hold the INFO button for
a few seconds to switch in succes-
sion from reinitialisation mode
1

(automatic) to reinitialisation mode

2 (manual) .
The mode selected is confi rmed.

I N S T R U M E N T S a n d C O N T R O L S
I
36
Restoring the manufacturer’s
parameters (REINITIALISE)
You can restore all of the manufacturer’s
settings for all of the functions.
On the menus screen:

 press the INFO button to select

“REINITIALISE”
(located on menu
2/2) .

 press and hold the INFO button for

at least 5 seconds .
An audible signal is heard and all of the
manufacturer’s settings are restored for
all of the functions. The manufacturer’s settings are: LIGHTING RHEOSTAT
With the lights on or off, press the button
to change the intensity of the lighting of
the instruments and controls in “day” or
“night” mode.
When the lighting reaches the maximum
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF. An audible signal is heard and the
intensity of the lighting increases
each time the button is pressed.
System for manual adjustment of the
brightness of the instruments and
controls in relation to the exterior
brightness.

Functions
Manufacturer’s
setting
Reinitialisation
of the average
consumption and
average speed
1 (automatic)
Fuel consumption
units
L/100 km
Temperature
display unit
°C
Display language ENGLISH
INFO button
sound
ON (activated)
Displaying of
the “BREAK
ADVISED”
message

OFF (deactivated)

I
37
MONOCHROME DISPLAY
This provides the following information:
- the time,
- the audio equipment displays (refer to the “Audio and Telematics” sec-
tion). Setting the time
The digital clock can be set in
automatic
mode or in
manual mode . Selecting the Setting
Select the
automatic mode or the

manual mode as follows:

 Press button A “PWR” to switch on
the audio system.

 Access the setting mode by press-
ing button B “TUNE” for approxi-
mately 2 seconds.

 Press button B “TUNE” several
times to scroll through the various
menus and select the CT menu
(clock time).
The order of the menus is the
following: AF / CT / REG / TP-S / PTY
display language / SCV / PHONE /
Functions setting mode OFF.
Automatic mode
This mode permits automatic setting of
the local time using the signal from the
RDS stations.
The symbol
“CT” appears on the
display.
Manual mode
This mode permits manual setting of
the time using the audio equipment
buttons.
It can also be used when the “Automatic
mode” displays an inaccurate time, when
the local RDS stations are broadcasting
from a different time zone.

I N S T R U M E N T S a n d C O N T R O L S
I
38
Set the time using the buttons as
indicated below:

 with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK button until the
time display fl ashes.
 Press the appropriate button to set
the time:

Button H: setting of the hour
The hours digits scroll when you press
this button.

Button M: setting of the minutes
The minutes digits scroll when you
press this button.

Button :00: resetting of the minutes to
zero.
- from 1 to 29 min
: rounded down to
the previous hour,
- from 30 to 59 min: rounded up to
the next hour.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
 After setting the time, press the

DISP button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the “minutes” display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.

 Turn button B “TUNE” to the left or
to the right to select “CT ON” (auto-
matic mode) or “CT OFF” (manual
mode).

 After selecting the mode, you can
exit the “Functions setting mode”
menu by pressing button B “TUNE”
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the “functions setting mode” menu
automatically.