2008 AUDI S8 engine

Instruments and warning/indicator lights
&, WARNING (continued )
extreme caution when working under the hood => page 299,
''Engine compartment "
[ i] Tips
Many functions are monitored by the Auto -Check system
=> page 28 . Ma lfunctions or faults wil l be identified either with a red
symbo l (pr iority 1
-Danger!) or with a yel low symbol (priority 2 -
Warning) .•
Electronic power control EPC
This warning/indicator light monitors the electronic
power control.
The EPC warning/indicator light (Electronic Power Control) i llumi ­
nates when you turn on the ignition as a function chec k.
[ i ] Tips
If this warning/indicator l ight i lluminates whi le you are driving, then
there is a malfunction in the engine electronics . Have the malfunc­
t ion corrected as soon as possible by your authorized Audi dea ler or
qualified repair facility .•
Generator D
This warning/indicator light detects a malfunction in the
generator or in the vehicle's electrical system.
The D warning/indicator light illuminates when you switch on the
igni tion and must go out a fter the engine has started.
If the
D warning/indicator light illuminates while you are driving,
you shou ld contact your authorized Audi dealer. Since the vehic le battery is discharging, you should switch off any unnecessary elec
­
t rical consumers (for example, the air conditioner).
0 Note
If the _f_ warning/indicator light (ma lfunction in the engine coo ling
system) in the instrument cluster shou ld
illuminate=> page 31, stop
the vehicle and turn off the engine . The water pump is not working
-this can cause engine damage. •
Electronic stabilization program (ESP) f1.
This warning/indicator light monitors the electronic stabi ­
lization program.
Th e warning/indicator light has the following functions:
• I t blinks while you are driving when the ESP is working .
• It illuminates when you switch on the ignition for approximate ly
2 seconds as a function check.
• It illuminates when there is a malfunction in the ESP. The
message
ESP fault! See owner's manual also appears in the instru­
ment cluster display and a warning tone sounds .
• It illuminates continuously when the ESP is switched off.
• It illuminates if there is a malfunction in the ABS, since the ESP
is part of the ABS sys tem.
If the battery terminals were disconnected and re-connected , the
vehic le was jump sta rted or the battery is very weak, the ESP sensor
system goes through a learning process for the first few yards. The
warning/indicator light illuminates. The warning/indicator light
goes out as soon as the learning process is complete.
If the ESP warning/indicator light illuminates and stays on after you
have started the engine, this may mean that the control system has
temporarily switched off the ESP . If this is case, you can reactivate
th e ESP by turning the ignition off and then on again . The
~

Instrum ents and warnin g/indi cat or li ghts
Significant loss of air pressure (l)
The warning/indicator light appears in the event of a
significant loss of air pressure .
The(!) warning/indicator light il luminates when you switch on the
ignit ion and must go out a fter the eng ine has started.
If the
U) symbo l appears, pressure is too low in at least one tire .
For more information
=> page 42 . •
Malfunction Indicator Lamp (MIL) 0
The Malfunct ion Indicator Lamp (M IU is par t of the On -Board Diag ­
nostic (OBD II) system . The symbol
O lights up when the ignition is
turned on and wi ll turn off after the engine has started and has
sett led at a constant id le speed. This ind icates that the M IL is
working proper ly .
The warning ligh t illum inates when there is a malfunction in the
engine electronic system . Contact your authorized Audi dealer and
have the mal function corrected.
An improperl y clos ed fuel filler c ap m ay als o cau se the MIL light t o
illuminate
=> page 303 .
For more information => page 27. •
Safety belts~
This warning/indica tor light reminds you to put on your
safety belt.
The t warning/indicator light i lluminates when the ignition is
sw itched on to remind the driver and any front passenger to put on
the safety belt . Add it ionally, an acoust ic warning (go ng) wi ll a lso
sound.
For more Information =>
page 209, "Safety belt warn ing light.(,..". •
Adaptive Air Suspension ~
The warning/indicator light ~ illuminates, when the jack ing mode
has been act ivated => page 188 . This warn ing/ indicator light has the
following functions:
• I t illuminates fo r a few seconds after the ignition is turned on as
function check and then goes out .
• I f the war ning/ indicator l ight illuminates steadi ly, there is a
system fau lt in the Adaptive Air Suspension . A system fault can
r esu lt in limited ride comfort and
low ground clearan ce . The fau lt
should be corrected as soon as possib le by an authorized Audi
dea ler.
• If the warning/indicator light flashes, you should not drive the
vehic le . The flas hing warning/indicator light points to an extreme
High level. A very
pronounced lifting of the vehic le (extreme High
l evel) can resu lt, for examp le, when a heavy load is removed from
the veh ic le. As soon as the level has returned to norma l, the
warning/indicato r light stops f lashing, and you can d rive away.
• If the warning/indicator light flashes in con junction with the c;::.:,
warning/indicator light, you shou ld not drive off immediately in
order to prevent damage to the underbody. The two warn ing/ indi­
cator lights flashing together points to an extreme Low level. A very
pronounced lowering of the vehicle (extreme Low level) ca n result,
for example, from a heavy load. As soon as the level has returned to
n ormal, the warning/ind icator lights stop flash ing, and you can
drive away .
0 Note
If the warning/indicator light flashes in conjunction with the c;::.:,
warning/indicator l ight, you shoul d not drive the veh icle because
l ow -lying vehic le parts can bottom out as you drive over uneven
ground and be damaged as a result .•

Instruments and warning/indicator lights
M alfun cti on in the ele ctronic differential lo ck (EDL )
The ED L wor ks t oget her wi th the ABS. T he ABS wa rn ing light w ill
come on if there is a ma lfunction in the ED L
system=> page 269. See
you r au thor ized A ud i dea ler as soon as possible.
& WARNING
• If the ABS (USA models )/0 (Canada models) warning light
doe s not go out , or if it comes on while driving , the ABS system is
not working properly. The vehicle can then be stopped only with
the standard brake s (w ithout ABS ). You will not have the protec ­
tion ABS provides . Contact your Audi dealer as soon as po ssible .
• USA model s: If the BRAKE warning light , the~ warning light and
the ABS warning light come on together , the rear wheels could
lock up first under hard braking . Rear wheel lock -up can cause loss
of vehicle control and an accident . Have your vehicle repaired
immediately by your authorized Audi dealer or a qualified work ­
shop . Drive slowly and avoid sudden , hard brake applications .
• Canada models : If the brake warning light (CD), the f;. warning
light and the ABS warning light
080 come on together, the rear
wheels could lock up first under hard braking. Rear wheel lock -up
can cause loss of vehicle control and an accident . Have your
vehicle repaired immediately by your authorized Audi dealer or a qualified workshop . Drive slowly and avoid sudden, hard brake
appli cations .
•
Electromechanical parking brake
tffiE (USA models) /{®) (Canada models)
T he war nin g/in dic ator l ight mon it ors the ele ctro mech an­
ical park ing brake .
With the parking brake applied and the ignition turned on, the
wa rning/ ind icator lig ht illu min a te s. Afte r the ig nition has been
turned off, the warning/indicator light continues to i llum inate for
abo ut 30 seconds. If the parking bra ke is a pplied with the ignition turned off, the warning/indicator light i
lluminates for about 30
seco nds.
T he warnin g/ind icator lig ht wi ll go out w hen the parking brake is
r elea sed .
I f t he war ning/indic ator l ig ht fl ashes con tinuously
after applying the
par king brake, bra king force is not sufficient to p revent the vehicle
fr om rol ling u nint en tional ly . This ca n happen if the br ak es b eco me
too hot . Please note the fol lowing :
• I f the slope of the g rou nd is too steep to pa rk t he ve hicle, the
addi tiona l dr ive message a ppears
Caution: Vehicle parked too
steep.
• I n the event of a parking brake ma lfunction , the yel low ·~ symbol
appea rs in the inst rument c luster display and the driver message
Parking brake malfunction ! is d isplayed . Have t he m alfu ncti on
r epaired as soon as possib le by a q ualified Audi dealership .•
Brake system BRAKE (USA models) /(©) (Canada
models)
T he warn ing/ind icator I i ght flash es if br ake fluid level is
low, if th ere is an A BS sys tem m alfunc tion or a p arki ng
br ake malf u n ct ion.
Th e li ght illu mi nates w hen t he ignit io n i s tur ned o n. It goes out afte r
the e ngine has been started . T his indicates that the bra ke warning
li ght is fu nct ioni ng prope rly.
If the brake warning light does not light up when the engine is
cranking , there may be a malfunction in the electrical system . In this
case , contact your Audi dealer.
If the brake system warning/indicator light flashes, there is a brake
syste m malfu nct ion . B y press ing th e
I CHECK ] butto n, you ca n brin g
up a driver message which exp lains the ma lfunction in more detail
::::> p~e~ ~

fl::. WARNING (c o ntinue d)
• Wo rk with d ue care when handl in g th e high -v o lt age secti on of
gas disc harge !xe non) lig ht s. Fa ilur e to d o so c ould re sult i n de ath
or seriou s injur y.
[ i J Tips
Have the bulb replaced or the connection repaired by your autho ­
rized Aud i Service department .•
Service interval display
The service interval display reminds you when your next
service is due.
Fi g. 14 D isplay:
Se rvice i nterval displ ay
The date for service is calculated automa tically. Based on the
average distance driven in previous months, a monthly driving
distance is calculated. As soon as the distance remaining to the next
service drops below the distance driven monthly, the service
reminder is initiated. The maximum period from one service to the
next is one year.
S erv ice reminder
30 days before the next service is due, a service reminder appears
in the display when you turn on the
i gnition => fig. 14.
Contro ls a nd eq uip­
ment
Dr ive r inf ormati on d ispl ay
After about 5 seconds the display switches back to normal. The
distance and time remain ing are updated each time the ignition is
turned on unti l the date due for service is reached.
Servi ce
When the due date for service is reached, the message Serv ice due
! appears in the disp lay immediately after you turn on the ignition.
Additionally, a warning tone sounds. After about 5 seconds the
display switches back to normal.
0 Note
I f you disconnect the battery terminals, no calculations can be
made for the service interval display during this time and no service
reminder will appear. Remember that observing the proper service
intervals is vita lly important to extending the life of you r vehicle,
particularly the engine, and maintaining its value. Even if the
mileage driven is low, the maximum period of one year from one
service to the next must not be exceeded. •
On-Board Diagnostic system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIU in the instrument cluster
=> page 16, fig. 7 is part of the On -Board Diagnostic (OBD II) system.
The warn ing/indicator light illum inates when the ignition is
switched on and goes out after the engine starts and the idle has
stabilized . This indicates that the MIL is working properly.
If the light d oes not go out after the engine is started, or illuminates
while you are driving, a ma lfunction may exist in the engine system.
If the light starts flashing, the catalytic converter cou ld be damaged.
Continue driving
w ith redu ced po wer (avoiding sustained high
speeds and/or rapid accelerat ions) and have the condition
corrected. Contact your authorized Audi dea ler.
Vehicle care I I irechnical data

Driver inf ormation displ ay
If the light illuminates, the e lectronic speed limiter may also be
malfunction ing. For more
information => page 28, "Electronic speed
limiter".
An impro perl y c los ed fu el fi ller c ap m ay also ca use the MIL light t o
illumina te
=> page 303. •
On-Board Diagnostics
Fig . 15 Locatio n of
D ata Link Connecto r
(DL Cl
On-Board Diagnost ics mon itors the components of your emission
control system. Each monitored component in your engine system
has been assigned a code . In case of a malfunction, the component
wi ll be identified and the fault stored as a code in the control
module memo ry.
The MIL light may a lso illuminate if there is a leak in the on-board
fue l vapor recovery system . If the light ill uminates after a refue lling,
stop the vehicle and make sure the fue l fi ller cap is proper ly closed
=> page 303.
In order to make an accurate diagnosis, the stored data can o nly be
displayed using special diagnostic equipment (generic scan tool for
OBD).
In order to connect the spec ial diagnostic equipment, push the p lug
into the Data Link Connector (DLC). The DLC is located to the right of
the hood re lease
=> fig. 15. Your authorized Audi dealer or a qua
lified service station can inter­
pret the code and perform the necessary repair. •
Electronic speed limiter
Your vehicle may be factory equipped with tires t hat are rated for a
maximum speed of 130 mph (210 km/h). This is less than the
maximum speed of your vehicle. To reduce the risk of sudden t ire
failure and loss of control if the vehicle is operated at excessive
speeds, your vehicle also has an electronic speed limiter. The e lec­
tronic speed limiter prevents your vehic le from going faster than the
tire speed rating . For more
information => page 336.
lf the veh ic le approaches the tire speed rating, the engine control
unit wi ll turn off the fue l injectors. You will notice an immediate loss
of engine power and a drop in road speed.
If the engine contro l unit receives faulty vehic le road speed signals,
the Ma lfunction Indicator Lamp (MIU
C:, wi ll i lluminate . If this
occurs, contact the nearest authorized Audi dealer for ass istance.
& WARNING
Al ways obser ve the po ste d speed limit s and adju st yo ur speed to
s uit prevailing road , traffic and we ath er condition s. N ever driv e
yo ur ve hicle f aster than the m aximum speed rating of the tire s
i nstalled .•
Auto Check Control
Introduction
T he Auto -Check contro l monitors the function of certain vehic le
features and components. I t simply makes sure these features and
components are working properly. The Auto -Check control works as
l ong as t he igni tion is on, as wel l as whenever the vehicle is
driven. ~

If a component is malfunctioning or if the need for an urgent repair
has been detected, this will appear in the instrument clus ter display .
You will a lso hear an audible warning tone . The displays are co lor
coded in either red or yellow depending on their level of priority.
A red symbol means
D anger , a yellow symbo l ind icates W arning . In
certain situations, information message for the driver appear in
addit ion to the red and yellow symbo ls .
Fun ction t est: au tom atic transmission
The Auto-Check Contro l will automat ically perform a test each time
you switch on the ignition. With the selector lever in
P or N , the
f ollowing message appears in the display:
When stati onar y appl y fo ot brake while selecting gea r.
When you a select a different gear (for example : R, D , etc.l, the
message will disappear and the Auto -Check function is disp layed.
If there is a malfunction , then the malfunction message will appear
about 15 seconds after the you start the vehicle . At the same time
you will hear a warning tone .•
Driver information messages
Driver i nfo rmation messages are shown in the instrument
cluster display in addition to the red and yellow symbols.
Controls and equip­ ment
Fig. 16 CHEC K button
in th e instru ment
c lu ster
Driv er information di splay
For example, if the transmission selector lever is not in the P posi­
ti on when the engine is turned off, the following message appears:
Shift t o P, otherwi se ve hic le can roll away. Doors do not lo ck if
le ver i s not in P .
The igni tion key can only be removed with the selector in this pos i­
tion. This and other messages are brought up if a function cannot
be car ried ou t.
Dri ver messa ges and r ed symbols
If a red symbo l appears in the display, a driver message can be
shown by pressing the [ CH ECK] button.
For example, the symbol f or a problem with engine oi l
pressure~
appears in the disp lay . If you then press the [ CHECK] button , the
fo llowing driver message appears in the d isp lay:
S witch off engine and che ck oil level
The driver message in the display goes out after about 5 seconds .
The dr iver message can be d isplayed aga in by briefly pressing the
[ CHECK] button .
Driver me ssages and yellow symbols
If a yellow symbol appears in the display, a driver message is also
displayed automat ica lly .
For examp le, the symbol
G> appears in the disp lay, indicating low
windshield washer fluid level. The following message also appears :
Please top up wa sher fluid
The driver message disappears after a few seconds . The driver
message can be d isplayed aga in by briefly pressing the [ CHECK]
button. •

Driver inf orma tio n displ ay
Red symbols
A red symbol means DANGER.
Pull off the road.
-Stop the vehicle .
-Turn off the engine.
Fig . 17 Dis play: en gine
co ola nt leve l warnin g
(pr iori ty 1)
-Check the malfunctioning system. Contact your aut ho-
rized Audi dea ler or a qua lified workshop for assistance.
Red symbols indicate a prio rity malfunction -Danger!
With a priority 1 malfunction, a large symbol appears in the center area of the
disp lay => fig. 17. When the symbol appears, three
warning tones sound in succession . The symbol continues to blink
until the malfunction has been repaired .
After a few seconds, the large symbol is replaced by a small symbol shown at the top left of the display. This symbol is displayed until
the fault is corrected.
If there are more than one priority 1 malfunctions, the symbo ls
appear one after the other for about 2 seconds .
An additional driver message can a lso be d isplayed by briefly
pressing the
( CHECK) button .
The red symbols mean:
BRAKE
-
((l))
©
.....
[ i ] Tips
U SA m od els: => page 30
Brake system malfunction
C anad a mod els:
B rake system malfunction
II=> page 30
Engine coolant level too
=> page 31
low/engine coolant temperature
too high
En gine o il p ress ure too lo w
=> page 32
Faulty steering
=> page 33
Fa ult y ig nition s witch
=> page 33
• If the warning/indicator light
BRAKE (USA mode ls)/ <@ (Canada
models) in the instrument cluster flashes, there is a brake system
malfunction. By pressing the [
CHECK) button, you can bring up a
driver message which exp lains the malfunction in more detail.
Please
note=> page 30.
• Speed warnings threshold 1
8 (USA modelsl /8 (Canada
models) and threshold 2
8 . (USA models)/ 0, (Canada models) are
also shown as red symbo ls . The warning is a lways shown as a small
symbol in the upper area of the
display => page 36 . •
Brake system malfunction
A malfunction in the brake system must be repaired as
soon as possible.
If the warning /indi cator light BRAKE (USA models)/ ((D)
(Canada models) in the instr ument cluster flashes, there is
a brake system malfunction . By pressing the [
CHECK] ~

button, you can bring up a driver message which explains
the malfunction in more detail.
Stop vehicle and check brake fluid level
- Pull off the road.
- Stop the vehicle.
- Turn off the engine.
- Check the brake fluid level ::::>
page 317.
-Contact your nearest authorized repair facility if neces-
sary.
Brake fault ! Drive carefully to nearest workshop
- Drive carefully to the nearest authorized repair facility
and have the malfunction corrected
=> &.
Parking brake ! Please contact workshop
- If the warning/indicator light flashes when the vehicle is
stationary or after the ignition is turned on, check to see
if the parking brake can be released. Drive to an autho­
rized repair facility as soon as possible and have the
malfunction corrected. If the parking brake cannot be
released, contact your nearest authorized repair facility.
- If the warning/indicator light flashes while you are
driving, it is possible that the traction control or the
emergency brake has malfunctioned. It is possible that
the parking brake cannot be applied. It is also possible
that the parking brake cannot be released after it has
been applied. Drive to an authorized Audi dealer to have
the malfunction corrected.
Controls and equip­
ment
Driver information display
If the ABS, ESP and the brake force distribution fail , the ABS
warning/indicator light and the ESP warning/indicator light come
on along with the brake system malfunction warning/indicator light
=>& .
& WARNING
• Always observe the warnings in => page 299, "Engine compart­
ment", before opening the hood and checking the brake fluid.
• Driving with low brake fluid is a safety hazard. Stop the car and
get professional assistance .
• USA models: If the BRAKE warning light, the !';. warning light and
the ABS warning light come on together, the rear wheels could
lock up first under hard braking. Rear wheel lock-up can cause loss
of vehicle control and an accident. Have your vehicle repaired
immediately by your authorized Audi dealer or a qualified work­
shop. Drive slowly and avoid sudden, hard brake applications.
• Canada models: If the brake warning light ((D), the 1$ warning
light and the ABS warning light
0 come on together, the rear
wheels could lock up first under hard braking. Rear wheel lock-up can cause loss of vehicle control and an accident . Have your
vehicle repaired immediately by your authorized Audi dealer or a qualified workshop . Drive slowly and avoid sudden, hard brake
applications. •
Engine cooling system malfunction -L
A malfunction in the engine cooling system must be
repaired as soon as possible.
When the -L symbol in the display blinks, then either the
engine coolant
temperature is too high, or the coolant level
is too low. An additional driver message can also be
displayed by pressing the
[CHECK] button:
Switch off engine and check coolant level