2008 AUDI S8 ECO mode

The speed warning 2 symbol, 8, (USA models)/ 8, (Canada models)
appears in the disp lay when you exceed the stored speed limit.
Un like warning 1, it wil l not go out unti l the vehicle speed drops
below the stored speed limit .
Setting speed warning 2
=> page 37.
[ i J T ips
Even though your vehicle is equipped with a speed warning system,
you should still watch the speedometer to make sure you are not
driving faster than the speed limit. •
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the I CHECK) button.
(CHECK • fo.o'
Storing the maximum speed
- Drive at the desired maximum speed.
Fig . 19 C HEC K but ton
in th e inst ru m ent
c lu st er
- B riefly press the I CHECK) b utto n ~ fig. 19.
Rese tting the m aximum speed
- Drive the vehicle at a speed of at least 3 mph (5 km/h)
- Press the
I CHECK] button for more t han 1 second .
Controls and eq uip­
ment
Dr ive r inf ormati on d ispl ay
The speed warning symbol 8 (USA models)/ 8 (Canada mode ls) will
appear briefly in the display when you release the button to indicate
that the maximum speed has been stored successfully.
The maximum speed remains stored unti l it is changed by pressing
the button again briefly or unti l it is deleted by a lengthy push on the
button. •
Speed warning 2 : setting a speed limit
Warning threshold 2 is set, changed and deleted in MM/.
Fig. 20 MMI d isp lay :
Se t w arni ng thr esho ld
2
Switching spe ed warning on and off
- Press the
I CAR) function button.
- Select
System s in the CAR menu.
- Select
Instrume nt clus ter . The Instrument cluster menu
appea rs~ fig. 20.
- Select Speed warning
On to switch on the warn ing
threshold or
Off to turn off the warning threshold.
Setting and adju sting th e warning threshold
- Press the
I CAR I fu nction button.
Select
Systems in the CAR menu.
Vehicle care I I irechnical data

Driver information display
-Select Instrument cluster. The In strument cluster menu
appears .
Select the second item in the
Speed warning menu. The
submenu
Speed threshold appears ~ page 37, fig. 20.
Set the warning threshold you want .
Warning threshold 2 can only be set in a speed range from 20 to
150 mph (30 to 240 km/h). •
Trip computer
Introduction
The trip computer gives you information on current and
average fuel mileage, average speed, fuel range and
driving time.
Fig. 21 Trip comput er
di sp lay : Average fuel
mil eage
The following driving information is continuously evaluated by the
trip computer and can be displayed sequential ly in the instrument
cluster display.
Fuel range
The estimated cruising range in miles (km) appears in the display.
This tells you how far your vehicle will be able to travel on the current tank of fuel and with the same driving style. The display
changes in increments of 6 miles (10 kml.
The cruising range is calculated based on the fuel consumption for
the last 18 miles (30 km). If you drive conservative ly, the cruising
range will increase.
Average fuel mileage
The average fuel economy in MPG (1/100 km) since you last cleared
the memory appears in this display . You can use this disp lay to
adjust your driving technique to achieve a desired mileage .
Current fuel mileage
The instantaneous fuel consumption in miles per gallon (1/100 km)
is shown in this display. You can use this display to adjust your
driving technique to achieve a desired mileage.
Fuel consumption is recalculated at interva ls of 33 yards (30
metres). When the vehic le is stationary, the most recent fuel
consumption is displayed.
Average speed
The average speed in mph (km/h) since the last time the display was
reset appears in the display.
Elapsed time
The length of time that you have been driving since you last reset
the memory appears in this display .
[ i] Tips
• Fuel consumptions (average and current), range and speed are
displayed in metr ic units on Canadian models.
• All stored values will be lost if the vehicle battery is
disconnected .•

is pressed. If the check light does not flash, the battery is dead and
has to be replaced .
In addition, when the battery is dead the
!i, symbol appears in the
instrument cluster display as well as the message:
!i, Pl ease chang e key batte ry
We recommend having the battery changed by an Audi Dealer .•
Electronic immobilizer
The immobilizer helps to prevent unauth orized use of
y o ur vehicle.
A computer chip inside your key automatica lly deactivates the e lec ­
t ronic immobilizer when you insert the key in the ignition lock, or on
vehic les with Advanced Key*, when the key is inside the vehicle .
When you remove the key from the ignition lock, or on vehicles with
Advanced Key, when you remove the key from the vehicle, the elec­
t ronic immobilizer is automatically activated once again.
If an unauthorized key was used,
S AFE is disp layed continuous ly in
the odometer disp lay field.
& WARNING
Alw ays tak e the k ey with you wh en you le ave th e vehicl e. The k ey
ca n di sarm th e ele ctr onic engin e immobili zer and permit an un au­
thorized p ers on to start th e eng in e and enable opera tion of the
v ehicle system s such as power window or power sunroof l eading
to ser iou s per son al in jur y.
[ i ] Tip s
• Your engine can on ly be started using the factory -equipped key.
• You may not be able to start your vehic le if an ignition key of a
different vehicle make is also located on your set of keys .•
Controls and equip­
ment
Openin g and clo sing
Certification
The remote control device comp lies with
• USA models: Part 15 of the FCC Rules .
• Can ad a m odels: RSS -210 of Industry Canada .
Operation is subject to the f ollowing conditi ons :
• this device may not cause harmful interference, and
• t his device must accept any interfere nce rece ived, i ncluding
interference that may cause undes ired operation.
0 Note
The manufacturer is not responsib le for ANY RA DIO OR TV interfer­
ence caused by unauthorized modifications to this equipment .
Changes or modifications to this unit not express ly approved by the
party responsible for compliance could void the user's authority to
operate the equipment. •
Power locking system
General description
The power locking system locks or unlocks all doors and
the rear lid simultaneously.
The power locki ng system in your veh ic le incorporates the following
functions:
• Central lock ing function
• Selective unlock
feature=> page 52
• Remote contro l feature=> page 48
• Advanced Key *=> page 59
• Anti -theft alarm system=> page 67

Le avi ng hom e
The Leaving home functions ensures that when unlocking the
vehicle periphery is i lluminated in the dark . In addition, the fron t fog
lights, the tai l lights and the license plate light a re turned on. Th is
function can be turned on and off .
High beam
With the switch in the AUTO position, the high beams can be turned
on only if the function is turned
on.
D aytime ru nning l ight s
USA models:
The daytime running lights can be turned on or off
using this function .
Canada models: The function cannot be tu rned off . It is activated
automatically each time t he ignition is turned on. This menu item is
shown "greyed out" .•
Front fog lights }0
Fi g. 58 Ins tru men t
pan el: lig ht swit ch
Switching on the front fog lights }D
- Do not turn the light switch -r:;_ -=> fig. 58 toward the fog
l ight symbol
- Tu rn t he light switch to
~oo: o r to fD .
Contro ls a nd eq uip­
ment
Clear vision
- P ull the ligh t switch to th e fi rst st op G) .
When the front fog l ights are on, the symbo l }D next to the ligh t
switch will illuminate .
[ i ] Tips
With the switch in AUTO front fog lights and rear fog lights cannot
b e turned on in addition .•
R ear fog lights 0$
Fig . 59 In strument
p an el: lig ht sw itc h
- Do not turn the light sw itch -r:;_ -=> fig. 59 toward the fog
light symbol
- Turn the light sw itch to
~oo: or to fD.
- Pull the light swit ch t o th e second stop 0-
W hen the rear fog lights are on, both the }D and
the light switch will i llum inate. symbols next to
~
Vehicle care I I irechnical data

Clear vision
Fig. 75 Left rear roof­
lining: Vanity mirror
folded down
-To fold down, tap the rear edge of the mirror as indicated
by
arrow~ page 79, fig. 74.
As the mirror folds down, it automatically il lumina tes.•
Wiper and washer system
Windshield wiper ~
The windshield wiper lever controls both the windshield
wipers and the washer system.
Fig. 76 Windshield
wiper lever
The windshield wiper lever~ fig. 76 has the following posi ­
tions:
One-touch wiping
-Move the lever to position G) , when you want to wipe the
windshield
briefly.
Intermittent wiping <:S;)l (activating rain sensor)
-Move the lever up to position ®·
-Move switch © up or down, to adjust the sensitivity of
the rain sensor.
Low wiper speed
-Move the lever up to position G).
High wiper speed
-Move the lever up to position @.
Automatic wiper/washer
-Pull the lever to position© (toward the steering wheel)
and hold.
-Release the lever. The washer stops and the wipers keep
going for about four seconds.
Turning off the wipers
-Move the lever back to position @.
The windshield wipers and washer only work when the ignition is
turned on.
The rain sensor is only activated with the wiper leve r set to position
G) . When it starts to rain, the rain sensor will automatically activate
the intermittent wiping mode.
To reduce the sensitivity of the sensor, move switch
@ down. To
increase the sensitivity, move the switch up. The higher you adjust
the sensitivity, the faster the sensor will react when it senses mois-
.,_

________________________________________________ S_ e_ a_t _
s _a_ n_d _ s_t _o _ r_ a_ g~ e __ _
& WARNING
• The ski sack is intended only for the transportation of skis and
other light objects. To reduce the risk of serious personal injury,
never transport heavy or pointed objects in the ski sack.
• When braking rapidly or during an accident, the load could be
displaced and cause injury to occupants.
• Sharp edges on the load must be covered for protection.
Always fasten the belt tightly around the sack and its contents
=:> page 102, fig. 108.
[ i] Tips
Never stow the ski sack away when it is still wet or damp (for
example, snow melting from skis). Allow i t to dry completely before
stowing it away. •
Roof rack
First things first
A roof rack can be fitted to carry additional luggage on
the roof.
- Always read and follow the instructions provided by the
roof rack manufacturer when the roof rack system must
be installed.
If a roof rack or similar luggage carrying equipment is to be
installed, please note the following:
• To enhance the vehicle's streamlined design, rain gutters have
been molded into the roof. It is not possible to use normal roof
racks. Only install a roof rack specifically designed for your model
A8. Contact the nearest Audi dealer for information on approved modular roof racks for your vehicle.
Controls and equip­
ment
• These approved roof racks are the basis for a complete roof rack
system. Additional attachments for the basic roof rack are neces ­
sary to safely transport luggage, bicycles, surf boards, skis or small
boats. All necessary hardware for these systems is available at your
authorized Audi dealer.
• We recommend that you keep the installation instructions for
your roof rack system together with your Owner's l iterature in the
vehicle.
When should the roof rack be removed?
• Before going through an automatic car wash (it is best to ask the
car wash operator for advice)
• When not in use, to reduce fuel consumption, wind noise and to
guard against theft.
& WARNING
• Use of an unapproved roof rack or incorrect mounting of an
approved roof rack can cause the roof rack or the items attached
to it to fall off the roof onto the road.
• Objects falling from the roof of a vehicle can cause a crash and
personal injury.
• Only mount the system between the markings shown in
~ page 104, fig. 109.
• The roof rack system must be installed exactly according to the
instructions provided.
(D Note
• Your vehicle warranty does not cover any damages to the vehicle
caused by using roof racks or mounting struc tures not approved by
Audi for your vehicle. The same applies to damage resulting from
incorrect roof rack installation.
• Always check the roof rack mountings and hardware before each
trip and during a trip to make sure everything is securely tightened.
~

___ w_ a
_ r_m _ a_ n_d_ c_ o_ ld __________________________________________________ _
Warm and cold
Climate controls
Description
The air conditioner is fully automatic and is designed to
maintain a comfortable and uniform climate inside the
vehicle.
We recommend the following settings:
- Set the temperature to 75 °F (+23 °C).
- Press the !AUTO
I button.
With this setting, you attain maximum comfort in the least amount
of time. Change this setting, as desired, to meet your personal needs.
The climate controls are a combination of heating, ventilation and cooling systems, which automatically reduce humidity and cool the
air inside your vehicle.
The air temperature, air flow and air distribution are automatically
regulated to achieve and maintain the desired passenger compart­
ment temperature as quickly as possible.
The system automatically compensates for changes in outside
temperature and for the intensity of the sunlight entering the
vehicle. We recommend you use the
Automatic mode=> page 117
for year -round comfort.
Please note the following:
Turn on the air conditioner to reduce humidity in the vehicle. This also prevents the windows from fogging up.
When the outside temperature is high and the air is very humid ,
condensation from the evaporator may drip under the vehicle. This
is normal and does not indicate a leak. If the outside temperature is
low, the fan normally only switches to
a higher speed once the engine coolant has warmed up sufficiently.
The air conditioner temporarily switches off when you drive off from
a standstill using full throttle to save engine power.
The compressor also switches off if the coolant temperature is too high, so that the engine can be adequately cooled under extreme
loads.
Air pollutants filter
The air pollutants filter (a combined particle filter and activated
charcoal filter) reduces or prevents outside air pollution (dust, or pollen) from entering the vehicle.
The air pollutants filter must be changed at the intervals specified
in your Warranty
& Maintenance booklet, so that the air conditioner
can properly work.
If you drive your vehicle in an area with high air pollution, the filter
may need to be changed more frequently than specified in your
Audi Warranty
& Maintenance booklet. If in doubt, ask your autho­
rized Audi Service Advisor for advice.
Key coded settings
The air conditioner settings selected are automatically stored and
assigned to the key being used. When the vehicle is started, the air
conditioner automatically selects the settings assigned to that key.
This way every driver will maintain his/her own personal settings
and does not have to reset them manually.
If a different driver uses your key and changes the air conditioner
settings, the latest adjustments will erase and replace the settings
you have stored.
Energy management
To prevent the battery from being discharged and to restore the
balance of energy, components which require large amounts of

___ w_ a_ rm __ a_ n_ d_ c_ o_ ld __________________________________________________ _
Controls
This overview will help you to familiarize yourself with the
air conditioning controls.
Fi g. 1 29 Air cond it io ning co ntrol e lements
The left display indicates the temperature selected for the driver's
side, the right display indicates the temperature selected for the
passenger 's side.
The settings you make are shown in the MMI disp lay for a few
seconds when
MMI is turned on.
Each function is turned on or off by briefly pressing the corre ­
sponding button . The indicator light in the button illuminates when
the function is active. But- Fun
ction
II Page
ton (s )
ION/OFF) Turning on and off ~ page 117
Automatic mode ~ page 117
Contro l Temperature selection ~ page 717
knob
Q) Heated seats* ~ page 118
8 @ Ventilated sea ts* => page 118
00 Air distribution => page 120
~ Defrost ~ page 120
=> page 723
00 Fan => page 120
~ Manual recirculation ~ page 721
@@ Heated rear window ~ page 124
!SETUP) Basic settings => page 126
[ i ] Tip s
• Residual h eat : With the ignition turned off, you can activate the
residual heat function by pressing the
I ON/OFF ) button. The
residual heat from the coo lant can be used to heat the vehicle inte ­
rior. The residua l heat function is turned off automatically after 30
minutes.
• Synchroniz ing clim ate control: By press ing and ho lding the
control knob on the driver's side, the temperature setting on the
driver's side can be switched to the passenger's side , and vice versa.
In the case of vehicles with rear air conditioning*, the selected
t emperature setting is also app lied to the o uter rear seats. The new
temperature is shown in the display. •