2008 AUDI A4 AVANT warning

-Emergency situations PW--------=----=---------------
4. Connect clamp on opposite end of negative cable to the
negative(-) terminal© of the discharged vehicle battery
@.
- Check that all screw plugs on the battery cells are
screwed in firmly. If not, tighten plugs prior to
connecting clamp on negative battery terminal.
Starting the engine
-Start the engine of the vehicle with the booster battery.
Run the engine at a moderate speed.
- Start engine with discharged vehicle battery in the usual
manner .
- If the engine fails to start: do not keep the starter
cranking for longer than 10 seconds. Wait for about 30
seconds and then try again.
- With engine running, remove jumper cables from both
vehicles in exact
reverse order.
The battery is vented to the outside to prevent gases from entering
the vehicle interior.
Make sure that the jumper clamps are well connected with their
metal parts in full contact with the battery terminals .
& WARNING
To avoid serious personal injury and damage to the vehicle, heed
all warnings and instructions of the jumper cable manufacturer. If
in doubt, call for road service.
• Jumper cables must be long enough so that the vehicles do not
touch.
• When connecting jumper cables, make sure that they cannot
get caught in any moving parts in the engine compartment.
& WARNING (continued)
• Before you check anything in the engine compartment, always
read and heed all
WARNINGS:::::, page 265, "Engine compartment".
0 Note
Improperly connected jumper cables can damage or destroy the
generator .
• Always connect POSITIVE (+l to POSITIVE(+), and NEGATIVE (-l to
NEGATIVE (- l terminal.
• Check that all screw plugs on the battery cells are screwed in
firmly. If not, tighten plugs prior to connecting clamp on negative
battery terminal.
• Please note that the procedure for connecting a jumper cable as
described above applies specifically to the case of your vehicle
being jump started. When you are giving a jump start to another
vehicle, do not connect the minus 1-1 cable to the minus (-1 terminal
on the discharged battery @::::, page 331, fig. 234. Instead, securely
connect the minus (-l cable to either a massive metal component
that is firmly bolted to the engine block or to the engine block itself .
If the battery that is being charged does not vent to the outside,
escaping battery gas could ignite and explode! •
Emergency towing with commercial
tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by commercial tow truck
operators who know how to operate their equipment safely.
• Never tow your Audi, towing will cause damage to the engine
and transmission. .,_

Emergency situations -
----------------=-----'
• Never wrap the safety chains or winch cables around the brake
lines.
• To prevent unnecessary damage, your Audi must be transported
with a car carrier (flat bed truck).
• To load the vehicle on to the flat bed, use the towing loop found
in the vehicle tools and attach to the front or rear anchorage
=> page 333 and => page 334.
& WARNING
A vehicle being towed is not safe for passengers. Never allow
anyone to ride in a vehicle being towed, for any reason. •
Front towline eye
Do not install the front towline eye until it is needed.
Fig. 235 Front
bumper: removing the
cover cap Fig. 236 Front
bumper: towline eye
fully screwed in
The towline eye fits into the threaded hole located on the
right side of the front bumper and covered by a small cap
when not in use .
-Remove the towline eye from the vehicle tools
=} page 316.
-Press on the bottom edge of the cover cap to disengage
and take it out of the bumper. The cap remains
connected to the bumper :::} fig. 235.
-Insert the towline eye into the threaded hole:::} fig. 236
and turn it all the way in until it is seated securely, then
tighten it with the wheel bolt wrench.
When it is no longer needed, unscrew the towline eye and put it
back into the on-board toolkit. Make sure to have the towline eye
stored in the vehicle at all times. .,_
Do-it-yourse lf service irechnical data

ffl....__E_ m
_ e
_ r-=g '--e_ n_ c...:y _ s_ i_t _u _a _t_ i_o _n_ s _______________________________________________ _
& WARNING
If the towing loop is not screwed in as far as it will go, the thread
can pull out when the vehicle is towed
-potential risk of an
accident .•
Fixed rear towline eye
* ,-- -===================:---ii
Fig. 237 Rear bumper,
right side: location of
rear towline eye
The rear towing eye is welded to the chassis under the rear bumper
on the right side. •
Front hook up
These steps apply for winching the vehicle onto a car
carrier with the front first.
Fig. 238 Vehicle
secured to flatbed
truck
- Have the vehicle aligned centered with the car carrier
ramp.
- Attach the winch hook to the
front towl ine eye previously
installed=> page
333.
-Once the car is positioned on the car carrier, have safety
chain(s) attached to the rear towline eye and tightened.
[ i] Tips
Check careful ly to make sure the vehicle is hooked up securely
before moving the car up the car carrier ramp.•

Emergency situations -
----------------=-=---
Rear hook up
These s te p s app ly fo r w in chi ng the vehi cle on to a car
c arr ier w ith the re a r f ir st.
- Have the vehic le ali gne d cent ered wi th the ca r carr ier
r a mp.
- Attach the win ch hook to t he
rear to wline eye
=> pa ge 334, fig. 237 .
- On ce th e ca r is po sit io ned on t he car ca rrie r, ha ve safety
c hain (s ) a ttach ed t o the
fron t towline eye => pag e 333an d
ti ghte ned .
[ i] Tips
Chec k carefu lly to ma ke sure the veh icle is hoo ked up securel y
b ef ore mov ing the ca r up the ca r ca rrier r amp. •
Lifting the vehicle
Important safety precautions
Be aware of the following hazards before l ift ing the vehic le w ith a
w ork sho p ho is t or f lo or jack :
• The vehicle should never be lifted or jacked up from underneath
the engine oil pan, the transmission housing , the front or rear axle
or the body side members . This could lead to serious damage.
• Use lifting equipment with padded contact surfaces to avoid
damage to the underbody or chassis frame.
• Alternatively, cover the contact surfaces on workshop hoist or
floor ja ck with rubber pads before lifting.
• Before driving over a workshop hoist , check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist. •
Before driving over a workshop hoist , ensure that there is suffi ­
cient clearance between the hoist and low parts of the vehicle .
& WARNING
To reduce the risk of serious injury and vehicle damage:
• Always lift the vehicle only at the special workshop hoist and
floor jack lift points illustrated
=> fig . 239 and => fig . 240 .
• Failure to lift the vehicle at these points could cause the vehicle
to tilt or fall from a lift if there is a change in vehicle weight distri­
bution and balance . This might happen, for example, when heavy
components such as the engine block or transmission are
removed .
• When removing such heavy components, anchor vehicle to
hoist or add corresponding weights to maintain the center of
gravity . Otherwise , the vehicle might tilt or slip off the hoist ,
causing serious personal injury .
•
Do-it -yourself service

lll9....__E_ m_ e_ r
-' g==-- e_n _c_ y,__ s_ i_ t _u _a _ t_ i_o _n _ s _____________________________________________ _
Lifting points for workshop hoist or floor jack
If you must lift your vehicle with a floor jack to work
underneath, be sure the vehicle is safely supported on
stands designed for this purpose.
Lifting points, front and rear
~ w 00 CD
Fig. 239 Driver's side:
front lifting point
behind forward wheel
well
Fig . 240 Driver's side:
rear lifting point ahead
of rear wheel well
The positions of the front and rear lifting points are indicated by
small
raised triangular markings below the door sill on either side . The lifting points themselves are located on the floor pan reinforce­
ment ribs running along the length of the car.
Lifting with vehicle jack
Refer to=> page 321. •
Lifting with workshop hoist and with floor
jack
- Use lifting equipment with padded contact surfaces to
avoid damage to the underbody or chassis frame.
- Alternatively, cover the contact surfaces on workshop hoist or floor jack with rubber pads before lifting.
- Read and heed WARNING ::}
& in "Important safety
precautions" on page
335.
-Locate the proper lifting points ~ page 336, fig. 239 and
=} page 336, fig. 240 .
- Adjust the lifting arms of the workshop hoist or floor jack to align with the lifting points.

_________________________________________________ G_ e_ n_ e_r _a _l_ i_n _f_o _ r_ m_ a_ t
_ i
_ o _ n
__ __
T he sa fe ty co mplia nce s ticke r
is your assurance t hat your new vehicle complies with a ll applicable
Federa l Motor Vehic le Safety Standards which were in effect at the
t ime the veh ic le was manufactured . You can find t his st icker on the
left door jamb. It shows the mon th and year of production and the
vehic le identification number of your vehic le (perforation) as well as
the Gross Veh icle Weight Rating (GVWR) and the Gross Axle Weight
Rating (GAWRl.
Th e high volt ag e wa rning la bel
is located on the lock carrier .
The spark ignition syste m mee ts all requirement s of the Canadi an
Interf ere nc e-C au si ng Equipm ent Regulati ons. •
Weights
Gross Veh icle Weight R ating
The G ross Veh ic le Weight Rat ing (GVWR), and the Gross Ax le Weight
Rating (GAWR) for front and rear are listed on a sticker on the left
door jamb .
The Gross Vehicle Weight Rating includes the we ight of the basic
vehic le plus fu ll fuel tank, oil and coolant, plus maximum load,
whic h inc ludes passenger weight ( 150 lbs/68 kg per designated
seating position) and luggage weight.
Gr oss Axle Weight Ra ting
The Gross Ax le Weight Rating is the maximum load that can be
app lied at each axle of the
veh ic le =:> & .
Vehicl e cap acit y w eight
The vehicle capacity weight (max. load) is listed either on the
driver's side 8 -pillar or inside the fuel fi ller f lap .
Controls and equip­
ment Safety first Vehicle operation
Roof
weight
The maximum permissible roof we ight is
165 lb (75 kg ). The roof
weight is made up of the weight of the roof rack system and the
weight of the object being
transported =:> page 117, "L oading the
roof rack".
LJ}. WARNING
• The actual Gr oss Axle Weight R atin g at the front and re ar ax les
s hould not ex ceed the permi ssible w eight s, and th eir combination
mu st not e xceed the Gr oss Vehicle Weight R atin g.
• Exceeding pe rmi ssible weight ratin gs can re sult in vehicle
d am age , acc ident s and per son al inju ry.
0 Note
• The vehicle capacity weight figures apply when the load is
distr ibuted even ly in t he ve hicle (passengers and l uggage). When
transporting a heavy load in the luggage compartment, carry the
load as near to the rear axle as possib le so that the vehic le's
handling is not impaired .
• Do not exceed the maxim um permissib le axle loads or the
maximum gross vehic le weight. Always remember that the vehic le's
handling wi ll be affected by the extra load . Therefore, adjust your
speed according ly.
• Always observe local reg ulations. •
Dimensions
The specifications refer to the basic mode l. Differences may occur
depending on the mode l type and options ordered, for example, tire
sizes.
..,
Vehicle care Do-it-yourself service Technical data

_______________________________________________ C
_ o_ n
_ s_u _ m_ e_ r_l_ n _f_o _ r_ m_ a_ t
_ i
_ o _ n
__ lllll
W For the sake of the environm ent
By regularly ma intain ing your vehicle, you help make sure that emis ­
sion standards are maintained, thus minimizing adve rse effects on
the e nv ironment. •
Important considerations for you and your
vehicle
T he increasing use of elec tronics, sophisticated fue l injection and
emission con trol systems, and t he gene rally increasing tec hn ical
complexity of today's automobiles, have steadily reduced the scope
of maintenance and repai rs which can be carried ou t by vehic le
owners.
Also , safety and environmental concerns p lace very strict
limits on the nature of repairs and adjustments to engine and trans ­
m iss ion parts whic h an owne r can perform.
Maintenance , adjustments and repairs usua lly require special tools ,
t es ting dev ices a nd othe r eq uipment availab le to s pec ial ly t rai ned
workshop personne l in order to assure proper performance , reli ­
abil ity and safe ty of the vehicle and its many sy stems .
Im proper maintena nce, adjustments and repairs can impa ir the
operation and reliability of your vehicle and even void your vehicle
wa rranty. T here fore, proof o f servic ing in acc orda nce with the main­
tenance schedule may be a condition for upholding a possib le
warranty cla im made with in t he war ran ty per iod .
Above all, operationa l safety can be adversely affected, creating
unnecessary risks for you and your passengers.
I f in doubt about any servicing, have it do ne by your auth orized Audi
dea ler or any other properly equipped and qua lified workshop . We
str ongly u rge y ou to give yo ur auth orized Au di d ealer the oppo rtu ­
n ity to perform all scheduled maintenance and necessary repairs .
Yo ur dealer has the faci lit ies, origi nal par ts an d trained specia lis ts
to keep your vehic le running proper ly.
Controls and equip­ ment Safety first
Vehicle operation
Performing limited maintenan ce yourself
The following pages des cribe a li mi ted numbe r of proced ures wh ic h
can be performed on your vehicle with ordinary tools, should the
need a rise a nd trained pers onnel be unavaila ble. Before perfo rm ing
any of these procedures, a lways t horoughly read all o f the app li­
cable text and carefu lly fo llow the instructions given. Always rigor ­
ously observe the
WARNINGS provided.
Before you check anything in the engine compartment , always read
and heed all
WARNINGS ~ & and~ & in "Wo rking i n th e engine
compartment" on
page 273.
& WARNING
• Serious personal injury may occur as a result of improperly
performed maintenance , adjustments or repairs .
• Always be e xtremely careful when working on the veh icle .
Always follow commonly accepted safety practice s and general
common sense . Never risk personal injury .
• Do not attempt any of the maintenance, checks or repairs
described on the following pages if you are not fully familiar with
the se or other procedures with respect to the vehicle , or are uncer ­
tain how to pro ceed .
• Do not do any work without the proper tools and equipment .
Have the necessary work done by your authorized Audi dealer or
another properly equipped and qualified work shop .
• The engine compartment of any motor vehicle is a potentially
hazardous area . Never reach into the area around or touch the
radiator fan . It is temperature controlled and can switch on
s uddenly -even when the engine is off and the ignition key has
been removed . The radiator fan swit ches on automat ically when
the coolant reaches a certain temperature and will continue to run
until the coolant temperature drops .
• Alway s remove the ignition key before anyone gets under the
vehi cle .
.,_
Vehicle care Do-it-yourself service Technical data

llffl _ __::C:::.::: o:.:.n.:.: s:::.::: u:.:.m .:.:.: e:.: r~ I n:..:.:. f.::
o :.:.r .:.m :.:.:: a:.: t:.:. i.::o :.:.n.:.... _____________________________________________ _
&, W ARNING (continued )
• Always support your vehicle with safety stands if it i s neces­
sary to work underneath the vehicle. The jack supplied with the
vehicle is not adequate for this purpose and could collapse
causing serious personal injury .
• If you must work underneath the vehicle with the wheels on
the ground , always make sure the vehicle is on level ground , that
the wheels are always securely blocked and that the engine
cannot be started .
• Always make sure the transmission selector lever (automatic
transmission) is in
" P " (Park position) and the park brake is firmly
applied.
ffi For the sake of the environment
• Changing the engine settings wi ll adverse ly affect emission
l eve ls . T hi s is detri menta l to th e envi ro nm ent and increas es fu el
consumption .
• Always observ e env ironmenta l re gulations w hen disposing of
old e ngine oil, used brake f luid, dirty engine coo lant, spent batteries
or worn out tires .•
Additional accessories,
modifications and parts replacement
Additional accessories and parts
replacement
Alway s co nsult an autho rized Audi de aler before
pu rchasing acc essories .
Your vehicle incorporates t he latest safety d esig n f eatures ensuring
a high standa rd of active and pas sive safety . Th
is saf ety could be compromised by non -approved changes to the
v ehi cle . F or thi s re aso n, if par ts have to be re pla ced , pl ease obs erve
th e fo llow ing points when insta lling add itional acc essories :
A pproved Aud i accesso ries and gen uine Audi pa rts a re avai la bl e
fr om authori zed Aud i dea lers .
Th ese dealers also have the necessary faci lities, tools and tra ined
spec ia li sts to in sta ll th e parts an d acce ssor ies pr op erly .
& WARNING
Using the wrong spare parts or using non -approved accessories
can cause serious personal injury .
• Use only accessories expressly approved by Audi and genuine
Audi spare parts .
• These parts and accessories have been specially designed to
be used on your vehicle .
• Never install accessories such as telephone cradles or
beverage holders on airbag covers or within the airbag deploy­
ment zones . Doing so will increase the risk of injury if airbags are
triggered in an accident!
• Before you check anything in the engine compartment , always
read and heed all WARNINGS
=> page 265.
0 Note
• I f item s ot her than ge nuin e Audi s pa re pa rts, add- on eq uipment
and accessory items are us ed or if r epair wor k is not performed
according to s pecified methods, thi s can re sult in severe damage to
your v ehicle's eng ine and body (suc h as c orros io n) a nd advers ely
affect yo ur vehic le 's wa rranty.
• Th e manufacturer cannot be held liable for damage w hich occurs
d ue t o fa ilur e to comply w it h these stipu lation s.•