2008 Acura MDX Owner's Manual

ÛÝÛÝ
CONT INUED
Adjust Alarm Volume
Select the warning alarm volume
f rom three levels.
You can choose this customize item
f rom ‘‘METER SETUP’’ by pressing
the INFO ( / ) button repeatedly.Press the SEL/RESET button to see
the selections.
Select the desired level by pressing
the INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST ALARM VOLUME’’ and
repeat the procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
93
\f—\f—\fy\f\fy
()-
\fy\f\fy
2008 MDX

µ
µ
µ
µ ÛÝ
ÛÝ
Elapsed Time Reset
There are f our elapsed time reset
choices you can make:
MANUAL ONLY You can reset
the elapsed time, when Trip
Computer’s Elapsed Time is
displayed (see page ).
IGN OFF The elapsed time is
reset when you turn the ignition
switch to the LOCK (0) position.
TRIP A The elapsed time is reset
when the Trip A is reset.
TRIP B The elapsed time is reset
when the Trip B is reset.You can choose this customize item
f rom ‘‘METER SETUP’’ by pressing
the INFO ( / ) button repeatedly.
Press the SEL/RESET button to see
the selections.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
79
Multi-Inf ormation Display
94
\f—\f—\fy\f
y
()-
\fy\f\fy
2008 MDX

ÛÝ
CONT INUED
Auto Interior Illumination
You can choose this customize item
f rom ‘‘METER SETUP’’ by pressing
the INFO ( / ) button repeatedly.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ELAPSED TIME RESET’’ and
repeat the procedure again. While the headlight switch is turned
on, the interior lights gradually dim,
as the outside light level gets low.
You can customize at which outside
light level the lights start to dim.
ThereareMAX,HIGH,MID,LOW
and MIN levels and OFF for the auto
interior illumination settings.
If you want the illuminations to start
dimming as early as possible, select
MAX. For illuminations to start
dimming as late as possible, select
MIN. Choose HIGH, MID, or LOW
f or levels in between.
To disable the auto interior
illumination f unction, select OFF.
Multi-Inf ormation Display
Inst rument s and Cont rols
95
\f—\f—\fy\fy
()-
\fy\f
\f\fy
2008 MDX

ÛÝWhen your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
INTERIOR ILLUMINATION’’ and
repeat the procedure again.
Press the SEL/RESET button to see
the selections.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
96
\f—\f—\fy\f\fy
()-
\fy\f
\f
y
2008 MDX

Û
Ý
ÛÝ
ÛÝ
CONT INUED
Here are the two custom settings for
the position setup:MEMORY POSITION LINK
AUTO TILT & TELESCOPE
STEERING WHEEL
While ‘‘POSITION SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Position Setup
Inst rument s and Cont rols
97
SEL/RESET
BUTTON
INFO ( or )
BUTTON
\f—\f—\fy\fy
()-
\fy\f
\fy
2008 MDX

ÛÝÛÝ
Memory Position Link
If ‘‘MEMORY POSITION LINK’’ is
set to ‘‘ON,’’ the driver’s seat, the
steering wheel, and outside mirror
positions move to the position stored
in the memory when you open the
driver’s door, using the remote
transmitter.
You can choose this customize item
f rom ‘‘POSITION SETUP’’ by
pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘MEMORY POSITION LINK’’ and
repeat the procedure again.
Multi-Inf ormation Display
98
\f—\f—\fy\fy
()-
\fy\f
\fy
2008 MDX

ÛÝÛÝ
CONT INUED
Auto Tilt & Telescope Steering Wheel
When ‘‘AUTO TILT & TELESCOPE
STEERING WHEEL’’ is set to ‘‘ON,’’
the steering wheel automatically
moves f ully in and up when you turn
the ignition switch to the LOCK (0)
position and remove the key.
You can choose this customize item
f rom ‘‘POSITION SETUP’’ by
pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
TILT & TELESCOPE STEERING
WHEEL’’ and repeat the procedure
again.
Multi-Inf ormation Display
Inst rument s and Cont rols
99
\f—\f—\fy\fy
()-
\fy\f
\fy
2008 MDX

Û
Ý
ÛÝ
ÛÝ
INTERIOR LIGHT
DIMMING TIME
HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
While ‘‘LIGHTING SETUP’’ is
shown, press the SEL/RESET
button to enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Here are the three custom settings
f or the lighting setup:
Lighting Setup
Multi-Inf ormation Display
100
SEL/RESET
BUTTON
INFO ( or )
BUTTON
\f—\f—\fy\f\fy
()-
\fy\f
\fy
2008 MDX