2008 Acura MDX Owner's Manual

CONT INUED
Remove the bolt and use the f lat-
tip screwdriver to remove the
holding clips located under the
f ront bumper.
Push down the inner f ender.
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
1.
2.
Lights
Replacing Front Fog/Daytime
Running L ight Bulbs
Maint enance
405
SIDE MARKER LIGHT BOLT
HOLDING
CLIPS
BULB
SOCKET
Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the
glass can cause the bulb to overheat
and shatter.
\f—\f—\fy
\f

y
()-
\fy\f
\fy
2008 MDX

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Remove the two bolts, and remove
the rear light assembly f rom the
rear pillar.
Open the tailgate. Use a flat-tip
screwdriver protected with a cloth
to pry open the two covers.
Determine which of the two bulbs
is burned out: turn signal/hazard
lights or side marker light.
1. 2.
3.
3.
4.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
406
CONNECTOR
INNER FENDER COVER
BOLT
BOLT
\f—\f—\fy
\f
y
()-
\fy\f

y
2008 MDX

CONT INUED
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Install the rear light assembly in
the rear pillar. Tighten the two
bolts. Snap the bolt covers into
position.
Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
1.
4.
5. 6.
7.
8.
9.
Lights
Replacing a Back-up L ight Bulb
Maint enance
407
COVER
BULB SOCKET
\f—\f—\fy
\f
y
()-
\fy\f
y
2008 MDX

Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working. Place the cover back into the light
assembly. Push it up until it locks
in place.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
4.
5. 6.
2.
3. 7.
Lights
Side T urn Signal L ight
Rear L icense Plate Bulb
408
BULB
SOCKET
\f—\f—\fy
\f
y
()-
\fy\f
y
2008 MDX

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the climate control
system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.
Dirt build-up around the openings of
the seat belt anchors can cause the
belts to retract slowly. Wipe the
openings with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
Cleaning the Seat Belts
Dust and Pollen Filter
Dust and Pollen Filter, Cleaning the Seat Belts
Maint enance
409
OPENING
\f—\f—\fy
\f
y
()-
\fy\f
y
2008 MDX

The floor mats that came with your
vehicle hook over the f loor mat
anchors. This keeps the f loor mats
f rom sliding f orward, possibly
interf ering with the pedals, or
backwards, making the f ront
passenger’s weight sensors
inef f ective.
If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
Floor Mat s
410
Rear
Front
\f—\f—\fy
\f
y
()-
\fy\f
y
2008 MDX

Check the condition of the wiper
blades at least every 6 months.
Replace them if you f ind signs of
cracking in the rubber, and areas
that are getting hard or if they leave
streaks and unwiped areas when
used.To replace the f ront wiper blades:Raise each wiper arm of f the
windshield, lif ting the driver’s side
first, then the passenger’s side. Disconnect the blade assembly
from the wiper arm:
Press and hold the lock tab.
Slide the blade assembly toward
the lock tab until it releases
from the wiper arm.
When replacing a wiper blade, make
sure not to drop the wiper blade or
wiper arm down on the windshield.
2.
1.
CONT INUED
Wiper Blades
Maint enance
411
WIPER ARMS
LOCK TAB
Do not open the hood when the wiper
arms are raised, or you will damage the
hood and the wiper arms.
\f—\f—\fy
\f
\fy
()-
\fy\f
y
2008 MDX

Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm against the
window.
Windshield: Lower the passenger’s
side first, then the driver’s side.
Remove the blade f rom its holder
by grabbing the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder. 6.
7.
4. 5.
3.
Wiper Blades
412
BLADE BLADE
REINFORCEMENT
\f—\f—\fy
\f

y
()-
\fy\f
y
2008 MDX