2007 YAMAHA YBR250 key

3-13
3
INSTRUMENT AND CONTROL FUNCTIONS
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The system is OK. The motorcycle can be ridden.
This check is most reliable if performed with
a warmed-up engine.The neutral switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
The sidestand switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
The clutch switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
YES NO YES NO YES NO NOTE:
cap 3.pmd
24/1/2007, 14:37
13

5-1
5
OPERATION AND IMPORTANT RIDING POINTS
EAU15950
EWA10270
l
l l
l
l
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or function
that you do not thoroughly
understand.
l
l l
l
l
Never start the engine or operate
it in a closed area for any length
of time. Exhaust fumes are
poisonous, and inhaling them
can cause loss of
consciousness and death within
a short time. Always make sure
that there is adequate
ventilation.
l
l l
l
l
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised
completely, it could contact the
ground and distract the operator,
resulting in a possible loss of
control.
EAUW0090
Starting the engineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:l
The transmission is in the neutral
position.
l
The transmission is in gear with the
clutch lever pulled and the
sidestand up.
EWA10290
l
l l
l
l
Before starting the engine, check
the function of the ignition
circuit cut-off system according
to the procedure described on
page 3-12.
l
l l
l
l
Never ride with the sidestand
down.
1. Turn the key to “ON” and make sure
that the engine stop switch is set
to “
”.
ECAW0041
l
l l
l
l
The engine trouble warning light
should come on for a few
seconds, then go off. If the warning light does not go off,
ask a Yamaha dealer to check the
motorcycle.
l
l l
l
l
The speedometer needle will
sweep across the speed range
and then return to zero. The
tachometer needle will sweep
across the r/min range and then
return to zero. If either needle
does not sweep across their
ranges, ask a Yamaha dealer to
check the motorcycle.
2. Shift the transmission into the
neutral position.When the transmission is in the neutral
position, the neutral indicator light should
be on, otherwise have a Yamaha dealer
check the electrical circuit.3. Start the engine by pushing thestart switch.If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to
cap 5.pmd 24/1/2007, 14:37
1

5-4
5
OPERATION AND IMPORTANT RIDING POINTS
EAU17212
ParkingWhen parking, stop the engine, and then
remove the key from the main switch.
EWA10310
l
l l
l
l
Since the engine and exhaust
system can become very hot,
park in a place where
pedestrians or children are not
likely to touch them.
l
l l
l
l
Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.
ECA10380
Never park in an area where there are
fire hazards such as grass or other
flammable materials.
cap 5.pmd 24/1/2007, 14:37
4

6-26
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23624
Replacing the fusesThe main fuse and the fuse box, which
contains the fuses for the individual
circuits, are located under the seat. (See
page 3-9.)
20
1
2
1. Main fuse
2. Spare fuse1. Fuse box cover
2. Headlight fuse
3. Signaling system fuse
4. Fuel injection and ignition fuse
5. Display backup fuse
6. Spare fuse
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage.Specified fuses:
Main fuse:20.0 A
Headlight fuse: 10.0 A
Signaling system fuse:
10.0 A
Ignition and fuel injection fuse: 10.0 A
Backup fuse: 10.0 A
Spare fuses:
10.0 A and 20.0 A
ECA10640
Do not use a fuse of a higher
amperage rating than recommended
to avoid causing extensive damage
to the electrical system and possibly
a fire.3. Turn the key to “ON” and turn on
the electrical circuit in question to check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer check
the electrical system.
cap 6.pmd 24/1/2007, 14:38
26

9-1
CONSUMER INFORMATION
9
EAU26351
Identification numbersRecord the key identification number,
vehicle identification number and model
label information in the spaces provided
below for assistance when ordering
spare parts from a Yamaha dealer or for
reference in case the vehicle is stolen.
VEHICLE IDENTIFICATION NUMBER:MODEL LABEL INFORMATION:
EAU26400
Vehicle identification number
12
1. Vehicle identification number
2. Model yearThe vehicle identification number is
stamped into the steering head pipe.
Record this number in the space
provided.The vehicle identification number is used
to identify your motorcycle and may be
used to register your motorcycle with
the licensing authority in your area.
EAU33941
Model label1. Model labelThe model label is affixed to the frame
under the passenger seat. (See page
3-9.) Record the information on this label
in the space provided. This information
will be needed when ordering spare parts
from a Yamaha dealer.
cap 9.pmd
24/1/2007, 14:38
1