2007 YAMAHA YBR250 tow bar

3-4
3
INSTRUMENT AND CONTROL FUNCTIONSthe “SELECT” button, and then push the
“RESET” button for at least one second.
If you do not reset the fuel reserve
tripmeter manually, it will reset itself
automatically and the display will return
to the prior mode after refueling and
traveling 5 km (3mi).
Clock mode
To set the clock:1. Push the “SELECT” button and “RESET” button together for at
least two seconds.
2. When the hour digits start flashing, push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and the minute digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release it to start the clock.
Fuel meter
With the key in the “ON” position, the
fuel meter indicates the amount of fuel
in the fuel tank. The display segments
of the fuel meter disappear towards “E”
(Empty) as the fuel level decreases. When the fuel level reaches the bottom
segment near “E”, the fuel level warning
indicator and the bottom segment will
flash. Refuel as soon as possible.
EAU12347
Handlebar switches1. Pass switch“
”
2. Dimmer switch “
/
”
3. Turn signal switch “
/
”
4. Horn switch “
”1
2
1. Engine stop switch “
/
”
2. Start switch ”
”
cap 3.pmd 24/1/2007, 14:37
4

3-5
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU12350
Pass switch “
”
Press this switch to flash the headlight.
EAU12400
Dimmer switch “
/
”
Set this switch to “
” for the high beam
and to “
” for the low beam.
EAU12460
Turn signal switch “
/
”
To signal a right-hand turn, push this
switch to “
”. To signal a left-hand turn,
push this switch to “
”. When released,
the switch returns to the center position.
To cancel the turn signal lights, push the
switch in after it has returned to the
center position.
EAU12500
Horn switch “
”
Press this switch to sound the horn.
EAU12660
Engine stop switch “
/
”
Set this switch to “
” before starting
the engine. Set this switch to “
” to stop
the engine in case of an emergency, such
as when the motorcycle overturns or
when the throttle cable is stuck.EAU12710
Start switch “
”
Push this switch to crank the engine with
the starter.
ECA10050
See page 5-1 for starting instructions
prior to starting the engine.
EAU12820
Clutch lever1. Clutch leverThe clutch lever is located at the left
handlebar grip. To disengage the clutch,
pull the lever toward the handlebar grip.
To engage the clutch, release the lever.
The lever should be pulled rapidly and
released slowly for smooth clutch
operation.
The clutch lever is equipped with a clutch
switch, which is part of the ignition circuit
cut-off system. (See page 3-12.)
cap 3.pmd 24/1/2007, 14:37
5

3-6
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU12870
Shift pedal1. Shift pedalThe shift pedal is located on the left side
of the engine and is used in combination
with the clutch lever when shifting the
gears of the 5-speed constant-mesh
transmission equipped on this
motorcycle.
EAU12890
Brake lever
1
1. Front brake leverThe brake lever is located at the right
handlebar grip. To apply the front brake,
pull the lever toward the handlebar grip.
EAU12941
Brake pedal
1
1. Brake pedalThe brake pedal is on the right side of
the motorcycle. To apply the rear brake,
press down on the brake pedal.
cap 3.pmd24/1/2007, 14:37
6