2007 TOYOTA CAMRY headlight bulb

’07Camry_U (L/O 0608)
122
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
HighLow beams—For high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)—Pull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
even when the headlights are off.TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to position
1.
The ignition switch must be set at ON.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument panel flash faster
than normal, a front or rear turn signal
bulb is burned out. See “Replacing light
bulbs” on page 400 in Section 7−3.HEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1—Parking, tail, license plate,
side marker and instrument panel lights
The tail light indicator (green light) on the
instrument panel will tell you that the tail
lights are on.
Position 2—Headlights and all of the
above
Position 3 (“AUTO”)—Headlights and all of
the lights in the position 1
They automatically turn on or off depend-
ing on the darkness of the surroundings.
Headlights and turn signals
(for Canada)

’07Camry_U (L/O 0608)
125
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to position
1.
The ignition switch must be set at ON.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument panel flash faster
than normal, a front or rear turn signal
bulb is burned out. See “Replacing light
bulbs” on page 400 in Section 7−3.To turn on the emergency flashers,
push the switch.
All the turn signal lights will flash. To turn
them off, push the switch once again.
Turn on the emergency flashers to warn
other drivers if your vehicle must be
stopped where it might be a traffic hazard.
Always pull as far off the road as pos-
sible.
The turn signal light switch will not work
when the emergency flashers are operat-
ing.
NOTICE
To prevent the battery from being dis-
charged, do not leave the switch on
longer than necessary when the en-
gine is not running.
Emergency flashers

’07Camry_U (L/O 0608)
400
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the
wattage ratings given in the table.
The high mounted stoplight consists of a
number of LEDs. If any of the LEDs burn
out, take your vehicle to your Toyota deal-
er to have the light replaced.
CAUTION
To prevent burning yourself, do not
replace the light bulbs while they
are hot.
Halogen bulbs have pressurized gas
inside and require special handling.
They can burst or shatter if
scratched or dropped. Hold a bulb
only by its plastic or metal case.
Do not touch the glass part of a
bulb with bare hands.
NOTICE
Only use a bulb of the listed type.
The inside of the lens of exterior lights
such as headlights may temporarily fog up
when the lens becomes wet in the rain or
in a car wash. This is not a problem
because the fogging is caused by the
temperature difference between the outside
and inside of the lens, just like the
windshield fogs up in the rain. However, if
there is a large drop of water on the
inside of the lens, or if there is water
pooled inside the light, contact your
Toyota dealer.Light bulbsBulb
No.WTy p e
Headlights
(high)900560A
Headlights (low)—55B
Front side
marker lights—5C
Front turn
signal/parking
lights
3457NAK30/8D
Rear turn signal
lights—21D
Stop/tail and
rear side
marker lights
744321/5C
Tail lights
(type A)—5C
Tail lights
(type B)1943.8C
License plate
lights—5C
Back−up lights92116C
Front fog lights—55B
Front personal
lights—5C
Replacing light bulbs—

’07Camry_U (L/O 0608)
401
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Light bulbsBulb
No.WTy p e
Rear personal
lights—8C
Interior light—8E
Door courtesy
lights1685C
Vanity lights—8C
Glove box light—1.2C
Trunk light—3.8C
A: HB3 halogen bulbs
B: H11 halogen bulbs
C: Wedge base bulbs (clear)
D: Wedge base bulbs (amber)
E: Double end bulbsIf either the left or right front fog, front
turn signal/parking, front side marker,
tail or backup lights, or LED
∗ type
high mounted stoplight burns out, con-
tact your Toyota dealer.
NOTICE
Do not try to replace the front fog,
front turn signal/parking, front side
marker, tail or backup light bulbs by
yourself. You may damage the ve-
hicle.
∗: Light−emitting Diode3.5 L V6 (2GRFE) engine only—
Before replacing the headlight bulbs,
remove the cover clips and take off the
cover.
Remove and install the cover clip as
shown in the following illustrations.
—Front fog, front turn
signal/parking, front side
marker, tail and backup
lights, and LED
∗ type high
mounted stoplight —Headlights

’07Camry_U (L/O 0608)
402
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Removing clip
Installing clip
Low beam (outside)
High beam
(inside)
1. Open the hood. Turn the bulb base
counterclockwise to the front of the
vehicle as shown.
The above illustration shows the left−hand
headlight.2. Unplug the connector while depress-
ing the lock release.
If the connector is tight, wiggle it.