2007 RENAULT SCENIC display

POWER-ASSISTED STEERING
Fault finding – Introduction
36B
36B-3V5 MR-372-J84-36B000$066_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
Faults
Faults are declared present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but are not diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is switched on
after the + after ignition feed (without any system components being active).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the instructions in the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with
the fault.
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors for these lines (for oxidation, bent pins, etc.),
–the resistance of the component detected as defective,
–the condition of the wires (melted or split insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool because the
data is inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaints.
A synopsis of the general procedure to follow is provided on the following page in the form of a flow chart.

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-28V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Conformity check
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: engine stopped with the ignition on, without moving the
steering wheel, WHEELS STRAIGHT AHEAD (straight line driving).
FunctionParameter or Status Checked
or ActionDisplay and
notes Fault finding
Computer
electrical supplyPR108:Computer feed voltage10 V < X < 13 VIn the event of a fault with this
parameter, check the insulation,
continuity and absence of
interference resistance on the
computer earths and feeds (see
wiring diagrams). If the fault is still
present, carry out fault finding
on the charge circuit.
Steering wheel
angle (only for
Vdiag 05 and 09)ET020:Steering wheel angle
sensor programmingSTATUS 4In the event of a fault, apply the
interpretation of status ET020.
Multiplex signalsET023:Engine operationSTOPPED or
STALLEDIn the event of a fault, carry out
fault finding on the injection
system and the multiplex
network.
PR003:Vehicle speed0 mphIn the event of a fault, carry out
fault finding on the ABS and the
multiplex network.
Steering motor
powerPR012:Current absorbed by
the motor0 A (+ 1 A)In the event of a fault, apply the
interpretation of parameter
PR012.
AssistancePR014:Level of assistance
available100% (but
assistance
unavailable)In the event of a fault, apply the
interpretation of parameter
PR014.
TemperaturePR008:Computer temperature0˚C < X < 75˚CIn the event of a fault, apply the
interpretation of fault DF001
Motor thermal protection.
DAE_V05_CCONF/DAE_V09_CCONF/DAE_V0D_CCONF
MR-372-J84-36B000$528_fra.mif

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-29V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
Sub-function: assistance
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: engine stopped with the ignition on, without moving the
steering wheel, WHEELS STRAIGHT AHEAD (straight line driving).
FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
Steering wheel
angle (only for
Vdiag 05 and 09)ET020:Steering wheel angle
sensor programmingSTATUS 4In the event of a fault,
apply the interpretation
of status ET020.
PR121:Steering wheel angle- 10 d˚ < X < 10 d˚In the event of a fault,
apply the interpretation
of parameter PR121.
PR007:Steering wheel angle
drift compensation- 10 d˚ < X < 10 d˚In the event of a fault,
apply the interpretation
of parameter PR007.
TorquePR001:Torque applied to the
steering wheel0 Nm (+ 0.2 Nm)In the event of a fault,
apply the interpretation
of parameter PR001.
PR006:Steering motor torque
setpoint0 Nm (+ 0.2 Nm)In the event of a fault,
apply the interpretation
of parameter PR006.
AssistancePR014:Level of assistance
available100% (but assistance
unavailable)In the event of a fault,
apply the interpretation
of parameter PR014.
ComputerET026:Computer calibrationConfig. 1 < X < Config. 5In the event of a fault,
apply the interpretation
of status ET026.

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-30V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
Sub-function: assistance (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: engine stopped with the ignition on, without moving the
steering wheel, WHEELS STRAIGHT AHEAD (straight line driving).
FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
Multiplex signalsPR003:Vehicle speed0 mphIn the event of a fault,
carry out fault finding on
the ABS and the
multiplex network.
Steering motor
powerPR013:Setpoint for current
absorbed by the motor0 A (+ 1 A)In the event of a fault,
apply the interpretation
of parameter PR013.
PR012:Current absorbed by
the motor0 A (+ 1 A)In the event of a fault,
apply the interpretation
of parameter PR012.

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-31V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
Sub-function: power
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: engine stopped with the ignition on, without moving the
steering wheel, WHEELS STRAIGHT AHEAD (straight line driving).
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Computer
electrical supplyPR108:Computer feed
voltage10 V < X < 13 VIn the event of a fault with this
parameter, check the insulation,
continuity and the absence of
interference resistance on the
computer earths and feeds (see
wiring diagrams). If the fault is
still present, carry out fault
finding on the charge circuit.
TemperaturesPR008:Computer
temperature0˚C < X < 75˚CIn the event of a fault, apply the
interpretation of fault DF001
Motor thermal protection.
PR009:Steering motor
temperature0˚C < X < 130˚CIn the event of a fault, apply the
interpretation of fault DF001
Motor thermal protection.
Multiplex signalsET023:Engine operationSTOPPED or
STALLEDIn the event of a fault, carry out
fault finding on the injection
system and the multiplex
network.

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-32V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Test conditions: engine at idling speed.
STRAIGHT WHEELS (driving in a straight line).
FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
Computer
electrical supplyPR108:Computer feed
voltage12 V < X < 16 VIn the event of a fault with this
parameter, check the insulation,
continuity and absence of
interference resistance on the
computer earths and feeds (see
wiring diagrams). If the fault is still
present, carry out fault finding on
the charge circuit.
Steering wheel
angle (only for
Vdiag 05 and 09)ET020:Steering wheel
angle sensor
programmingSTATUS 4In the event of a fault, apply the
interpretation of status ET020.
Multiplex signalsET023:Engine operationRUNNINGIn the event of a fault, carry out
fault finding on the injection system
and the multiplex network.
PR003:Vehicle speed0 mphIn the event of a fault, carry out
fault finding on the ABS and the
multiplex network.
Steering motor
powerPR012:Current absorbed
by the motorWithout any action
on the steering
wheel:
0 A (± 1 A)
With action on the
steering wheel:
- 96 A < X <96 AIn the event of a fault, apply the
interpretation of parameter PR012.
AssistancePR014:Level of assistance
available100% (maximum
assistance)In the event of a fault, apply the
interpretation of parameter PR014.
TemperaturePR008:Computer
temperature0˚C < X < 7˚CIn the event of a fault, apply the
interpretation of fault DF001 Motor
thermal protection.

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-33V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
Sub-function: assistance
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Test conditions: engine at idling speed.
FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
Steering wheel
angle (only for
Vdiag 05 and 09)ET020:Steering wheel
angle sensor
programmingSTATUS 4In the event of a fault,
apply the interpretation
of status ET020.
PR121:Steering wheel
angle- 10 d˚ < X < 10 d˚
With action on the steering
wheel:
- 585˚ < X < + 585˚In the event of a fault,
apply the interpretation
of parameter PR121.
PR007:Steering wheel
angle drift
compensation- 10 d˚ < X < 10 d˚In the event of a fault,
apply the interpretation
of parameter PR007.
TorquePR001:Torque applied to
the steering wheelWithout any action on the
steering wheel:
0 Nm (± 0.2 Nm)
With action on the steering
wheel:
- 14 Nm < X <+ 14 NmIn the event of a fault,
apply the interpretation
of parameter PR001.
PR006:Steering motor
torque setpointWithout any action on the
steering wheel:
0 Nm (± 0.2 Nm)
With action on the steering
wheel:
- 5 Nm < X <+ 5 NmIn the event of a fault,
apply the interpretation
of parameter PR006.
AssistancePR014:Level of assistance
available100% (maximum
assistance)In the event of a fault,
apply the interpretation
of parameter PR014.
ComputerET026:Computer
calibrationConfig. 1 < X < Config. 5In the event of a fault,
apply the interpretation
of status ET026.

POWER-ASSISTED STEERING
Fault finding – Conformity check
36B
36B-34V5 MR-372-J84-36B000$528_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
Sub-function: assistance (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Test conditions: engine at idling speed.
FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
Multiplex signalsPR003:Vehicle speed0 mphIn the event of a fault,
carry out fault finding on
the ABS and the
multiplex network.
Steering motor
powerPR013:Setpoint for current
absorbed by the
motorWithout any action on the
steering wheel:
0 A (± 1 A)
With action on the steering
wheel:
- 96 A < X < 96 AIn the event of a fault,
apply the interpretation
of parameter PR013.
PR012:Current absorbed
by the motorWithout any action on the
steering wheel:
0 A (± 1 A)
With action on the steering
wheel:
- 96 A < X < 96 AIn the event of a fault,
apply the interpretation
of parameter PR012.