2007 RENAULT SCENIC service indicator

POWER-ASSISTED STEERING
36B
36B-11V5 MR-372-J84-36B000$330_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Configurations and programming
Summary table of configurations and configuration readings
GENERAL INSTRUCTIONS:
After replacing the EPAS computer/steering column unit, configure the computer's assistance strategy and program
the steering wheel angle sensor (only for Vdiag 05 and 09).
The following procedure must be followed in order to carry out the above configuration and programming:
–connect the diagnostic tool,
–switch on the ignition and establish dialogue with the electric power-assisted steering computer,
–select the "Repair mode" menu,
–configure the computer's assistance strategy and program the steering wheel angle sensor (see below),
–exit fault finding mode: stop dialogue with the electric power assisted steering computer without switching off the
CLIP tool,
–switch off the ignition for at least 15 seconds, without disconnecting the battery, for the configuration to be taken
into account by the EPAS computer,
–switch on the ignition again and establish dialogue with the electric power assisted steering computer,
–make sure the configuration readings have been properly registered,
–check that the system is operating correctly (steering assistance available when the engine is running).
A. STEERING WHEEL ANGLE SENSOR PROGRAMMING (only for Vdiag 05 and 09)
PROCEDURE COMPLETE:
(following replacement of the computer/steering column assembly).
Status ET020 Steering wheel angle sensor programming is STATUS 1 (SERVICE indicator light is continuously
lit, see interpretation of status).
–with the ignition on, connect the diagnostic tool and establish dialogue with the electric power assisted steering
computer,
–with the engine stopped or running (to obtain maximum steering assistance), turn the steering wheel to full left lock
and then to full right lock,
–set the vehicle wheels straight ahead, with the steering at the centre point (driving in a straight line),
–run command VP004 Steering wheel angle sensor programming by pressing the CONFIRM button,
–turn the steering wheel to full left lock and then to full right lock,
–Status ET020 Steering wheel angle sensor programming must be STATUS 4 (normal operational status),
–check that parameter PR121 Steering wheel angle varies within the limits indicated in the Conformity check
section and that DF038 Angle sensor is not present. VP001 Enter VIN ID010 VIN code
VP004Steering wheel angle sensor programming
(only for Vdiag 05 and 09)ET020Steering wheel angle sensor programming
(only for Vdiag 05 and 09)
VP005 Enter the APV* operation date ID018 Read last APV* operation date
SC001 Computer calibration ET026 Computer calibration
Note:
To obtain a precise wheels straight ahead position (straight line driving), carry out this operation on a front axle
adjustment bench (especially for vehicles fitted with ESP).
IMPORTANT
If the vehicle is fitted with ESP, establish dialogue with the ABS/ESP computer after the operation; if the function
is available (depending on the computer version) clear the ESP sensor programming using command RZ003.
Make sure there are no ESP faults: carry out the necessary operations by referring to the Fault Finding Manual.
MR-372-J84-36B000$330_fra.mif

POWER-ASSISTED STEERING
36B
36B-13V5 MR-372-J84-36B000$396_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Fault summary table
Tool
faultDiagnostic tool titleAssociated
DTCCustomer complaints and warning light
coming on
DF001Motor thermal protection5614Steering assistance intermittent reduction.
DF002Computer5608Assistance limited to 30% (with SERVICE
warning light + message) or no assistance
(with STOP warning light + message)
depending on the internal fault code.
DF020Computer supply5601Degraded assistance (no warning light or
message) until a loss of assistance below
9 V or above 17 V with STOP indicator light
+ Message.
DF021Steering wheel angle sensor
programming (only for Vdiag 05 and 09)5612Degraded steering wheel recall (with
SERVICE indicator light + message). ESP
fault, if present.
DF023+ after ignition feed5613Assistance gradually cuts out (within
5 minutes). When the ignition is next
switched on there is no steering
assistance.
DF033Multiplex networkD000Inappropriate level of assistance:
SERVICE indicator light + Message.
DF035Variable power assisted steering motor5606Assistance limited to 30% (with SERVICE
warning light + message) or no steering
assistance (with STOP warning light
+ Message).
DF038Angle sensor (only Vdiag 05 and 09) 5605Steering wheel recall degraded
(no warning light or message). ESP fault,
if present.
DF053Computer configuration5602Defect mode assistance (no message
or warning light).
DF054Torque sensor5604Steering assistance loss or absence with
STOP indicator light + Message.
DF055Computer memory5607Degraded assistance (without warning
light or message) or assistance limited to
10% with SERVICE warning light
+ Message.
Risk of ESP fault.
DF057Vehicle speed multiplex signalD200Inappropriate level of assistance:
SERVICE indicator light + Message.
Note:
Warning light/message
SERVICE + "Check steering" or,
STOP + audible warning + "Faulty steering" or "EPAS fault", depending on the type of instrument panel.
MR-372-J84-36B000$396_fra.mif

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-15V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF002
PRESENT
OR
STOREDCOMPUTER
DEF: Computer fault
NOTESPriority in the event of a number of faults:
In the event of an accumulation of faults, deal with the other present and stored faults
before applying the interpretation for this fault.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
–This fault causes an absence of steering assistance or a loss of steering assistance
and also illuminates the STOP indicator light + Message or assistance is limited to
30% and the SERVICE indicator light + Message come on.
Disconnect the 2 black connectors from the EPAS computer.
Check the condition and conformity of the connectors and their clips.
Check the conformity of the electrical supplies (they must be equal to the battery voltage).
In the event of a fault, check the insulation, continuity and the absence of interference resistance on the
following connections:
8-track connector track 8 + 12 V after ignition
2-track connector track 1 + 12 V before ignition feed
2-track connector track 2 Earth
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF002/DAE_V09_DF002/DAE_V0D_DF002

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-20V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF033
PRESENT
OR
STOREDMULTIPLEX NETWORK
DEF: CAN connection fault
NOTESConditions for applying the fault finding procedure to stored faults:
Apply this fault finding procedure.
Priority in the event of a number of faults:
Apply the interpretation of faults DF020 Computer supply and DF023 + after ignition
supply first, if they are present or stored.
Notes:
This fault may cause a reduction in steering assistance with the SERVICE indicator
light + Message.
Run fault finding on the multiplex network.
Carry out the necessary repairs.
Disconnect the 8-track connector from the EPAS computer.
Check the condition and conformity of the connector and its clips (terminals).
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
8-track connector of the EPAS computer
track 5 UCH
track 7 UCH
track 4 Instrument panel
track 6 Instrument panel
(see wiring diagram)
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF033/DAE_V09_DF033/DAE_V0D_DF033

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-21V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF035
PRESENT
OR
STOREDVARIABLE POWER ASSISTED STEERING MOTOR
DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
This fault causes a loss of assistance or an absence of steering assistance and also
illuminates the STOP warning light + Message, or assistance is limited to 30% and
the SERVICE indicator light + Message come on.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 3, 33, 34, 35, 50, 51, 112, 113, 128, 145 of PR143.
Contact Techline.
Procedure to apply for internal fault codes 4, 5, 100, 114, 115, 129, 130 and 131 of PR143.
Check the condition of the wiring inside the EPAS and make sure that the 3 white EPAS connectors are correctly
locked.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF035/DAE_V09_DF035/DAE_V0D_DF035

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-26V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF: EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault leads to degraded assistance with no warning light or message or an
assistance that is limited to 10% with the SERVICE indicator light + Message.
–Risk of ESP fault.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 83 and 85 of PR143.
Only for Vdiag 05 and 09:
Check status ET020 Steering wheel angle programming which should be STATUS 4; if not, program the
steering wheel angle sensor VP004 Steering wheel angle programming (see Configuration and
programming).
If the fault is still present after the ignition has been switched on several times, contact the Techline.
Procedure to apply for internal fault codes 84 and 86 of PR143.
Contact Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF055/DAE_V09_DF055/DAE_V0D_DF055

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-27V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF057
PRESENT
OR
STOREDMULTIPLEX VEHICLE SPEED SIGNAL
DEF: Invalid signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Notes:
This fault causes an unsuitable level of assistance and the SERVICE indicator light
+ Message come on.
Carry out fault finding on the multiplex network, and repair if necessary.
Carry out fault finding on the ABS (see 38C, Anti-lock braking system). If the ABS signals no fault and the EPAS
is the only system signalling the fault, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF057/DAE_V09_DF057/DAE_V0D_DF057

POWER-ASSISTED STEERING
Fault finding – Interpretation of statuses
36B
36B-37V5 MR-372-J84-36B000$660_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Interpretation of statuses
ET020
PROGRAMMING THE STEERING WHEEL ANGLE SENSOR
NOTESSpecial note:
–This status is declared correct when it is STATUS 4 (normal mode); in any other
case, apply this fault finding procedure.
–The SERVICE indicator light will come on if the steering wheel angle calibration has
not been carried out.
VARIOUS POSSIBLE STATUS VALUES (with the meaning):
STATUS 1:
–Straight ahead wheel position not programmed.
–Invalid angle value.
PROGRAMMING NOT COMPLETE.STATUS 3:
–Straight ahead wheel position not programmed.
–Invalid angle value.
–Steering wheel out of range ± 120˚ when after ignition
is switched on.
PROGRAMMING COMPLETE, ANGLE TO BE
CONFIRMED.
STATUS 2:
–Straight ahead wheel position not programmed.
–Invalid angle value.
PROGRAMMING NOT COMPLETE.STATUS 4:
–Straight ahead wheel position not programmed.
–Valid angle value.
PROGRAMMING COMPLETE.
STATUS 1 or STATUS 2
If the status is STATUS 1 or STATUS 2, program the steering wheel angle (see Configuration and
programming).
STATUS 3
If the status is STATUS 3, turn the steering wheel from right lock to left lock then slowly return it to slightly beyond
the centre point (PR135 "Column rotation speed" less than 200˚/s). The status should become STATUS 4.
Note:
A present or stored fault can impede STATUS 4 (carry out the necessary operations by referring to the Fault
Finding Manual).
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ET020/DAE_V09_ET020/DAE_V0D_ET020
MR-372-J84-36B000$660_fra.mif