2007 RENAULT SCENIC service indicator

POWER-ASSISTED STEERING
Fault finding – Customer complaints
36B
36B-47V5 MR-372-J84-36B000$858_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Customer complaints
NOTESOnly refer to the customer complaints after performing a complete check using the
diagnostic tool.
NO DIALOGUE WITH THE COMPUTER ALP1
LOSS OF VEHICLE ASSISTANCE WITHOUT WARNING ALP2
POOR VEHICLE HANDLINGALP3
THE STEERING WHEEL DOES NOT RETURN BY ITSELF
TO THE CENTRE AT LOW SPEED: STEERING WHEEL
RETURN TO CENTRE POINT INACTIVE (ONLY FOR
VDIAG 05 AND 09)ALP4
UNDER-ASSISTANCE AT LOW SPEED AND OVER-
ASSISTANCE AT HIGH SPEED WITHOUT WARNINGALP5
TOO LITTLE ASSISTANCEALP6
ASSISTANCE AVAILABLE FOR 5 MIN. AFTER
SWITCHING OFF THE IGNITIONALP7
ASSISTANCE AVAILABLE BUT CHECK STEERING
WARNING MESSAGE DISPLAYED AND SERVICE
INDICATOR LIGHT CONTINUOUSLY LITALP8
THE VEHICLE PULLS TO THE RIGHT OR TO THE LEFT ALP9
SERVICE INDICATOR LIGHT AND CHECK STEERING
MESSAGE COME ON STRAIGHT AWAYALP10
STEERING ASSISTANCE IS AVAILABLE WITH IGNITION
ON AND ENGINE STOPPED, WITH NO WARNINGALP11
THE ENGINE DOES NOT START AND THE MESSAGE
"STEERING NOT UNLOCKED" IS DISPLAYED
OR
THE MESSAGE "STEERING NOT UNLOCKED" IS
DISPLAYED AFTER THE IGNITION IS SWITCHED OFFALP12
MR-372-J84-36B000$858_fra.mif

POWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
36B
36B-55V5 MR-372-J84-36B000$924_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
ALP8Assistance available but Check Steering warning message
displayed and Service indicator light continuously lit
NOTESNone.
Check the vehicle battery voltage and the condition of the electric power-assisted steering connector.
Repair and check the charge circuit if necessary.
Vdiag 05 and 09: Check status ET020 Steering wheel angle programming which should be STATUS 4. If not,
program the steering wheel angle sensor VP004 Steering wheel angle programming (see Configuration and
programming).
If the fault is still present, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ALP8/DAE_V09_ALP8/DAE_V0D_ALP8

POWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
36B
36B-57V5 MR-372-J84-36B000$924_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
ALP10The Service indicator light and the Check Steering message
come on straight away
NOTESNone.
Check the conformity of the battery voltage and carry out fault finding on the charge circuit if necessary.
Check the condition and conformity of the ABS computer connector and its clips.
Check that the ABS computer has an electrical feed (see wiring diagram for the ABS fitted on the vehicle).
Disconnect the 8-track electric power assisted steering computer connector.
Check the condition and conformity of the connector and its clips.
Repair if necessary.
Carry out fault finding on the multiplex network, and repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
EPAS computer
(8-track connector)UCH
(PE2 40-track
connector)Protection and
Switching Unit
(CT1 12-track
connector)
track 7 track 8
track 5 track 18
track 6 track 8
track 16 track 1
track 3 ABS computer
track 2 ABS computer
(see wiring
diagram of the ABS
system installed in
the vehicle)
Repair if necessary.
If the previously checked connections are in conformity, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ALP10/DAE_V09_ALP10/DAE_V0D_ALP10