2007 PONTIAC GRAND PRIX start stop button

If the ignition or radio is turned off with a CD in
the player it stays in the player. When the ignition
or radio is turned on, the CD starts to play
where it stopped, if it was the last selected audio
source.
As each new track starts to play, the track number
appears on the display.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There may be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check the
bottom surface of the CD. If the surface of the CD
is damaged, such as cracked, broken, or
scratched, the CD will not play properly. If the
surface of the CD is soiled, seeCare of Your CDs
on page 279for more information.
If there is no apparent damage, try a known
good CD.Do not add any label to a CD, it could get caught
in the CD player. If a CD is recorded on a
personal computer and a description label is
needed, try labeling the top of the recorded CD
with a marking pen.
Notice:If you add any label to a CD, insert
more than one CD into the slot at a time, or
attempt to play scratched or damaged CDs, you
could damage the CD player. When using the
CD player, use only CDs in good condition
without any label, load one CD at a time, and
keep the CD player and the loading slot free of
foreign materials, liquids, and debris.
If an error appears on the display, see “CD
Messages” later in this section.
\1 (Forward):Press and hold this pushbutton
to advance quickly within a track. Press and
hold this pushbutton for less than two seconds to
advance at 10 times the normal playing speed.
Press and hold it for more than two seconds
to advance at 20 times the normal playing speed.
Release this pushbutton to play the track. FWD
and the elapsed time of the track appears on the
display.
272

RDM 2 (Random):To repeat the tracks in the
current folder or playlist, press and release
this pushbutton. FOLDER RANDOM displays.
Once all of the tracks in the current folder
or playlist have been played, the system moves
on to the next folder or playlist and plays all of the
tracks in random order.
To repeat the tracks on the CD, press and hold
this pushbutton for two seconds. A beep sounds
and DISC RANDOM displays. This feature
does not work with playlists.
When in random, pressing and releasing either
SEEK arrow takes you to the next or previous
random track.
Press and release this pushbutton again to turn off
random play. NO RANDOM displays.
3
#(Next Folder):Press this pushbutton to go
to the rst track in the next folder or playlist. If
the disc contains playlists, it goes through
the playlist, then the folders. Pressing this button
while in folder random mode takes you to the
next folder and random the tracks in that folder.
This function does not work on a CD that does not
contain folders or playlists.4 REV (Reverse):Press and hold this pushbutton
to reverse quickly within a track. Press and hold this
pushbutton for less than two seconds to reverse at
10 times the normal playing speed. Press and hold
it for more than two seconds to reverse at 20 times
the normal playing speed. Release this pushbutton
to play the track. REV and the elapsed time of the
track appears on the display. If this pushbutton is
pressed for more than 20 seconds, the radio stops
reversing and begins to play.
6
!(Previous Folder):Press this pushbutton
to go to the rst track in the previous folder or
playlist. If the disc contains playlists, it goes
through the playlist, then the folders. Pressing this
pushbutton while in folder random mode takes
you to the previous folder and random the tracks
in that folder. This function does not work on
a CD that does not contain folders or playlists.
wSEEKx:Press the up arrow to go to the start
of the next track. Press the down arrow to go to
the start of the previous track. Pressing either
arrow for more than two seconds searches
the previous or next tracks at two tracks per
second. When the track number that you would
like to play appears on the display, release
the arrow to stop searching and to play the track.
273

TPMS Sensor Identication Codes
Each TPMS sensor has a unique identication
code. Any time you replace one or more of
the TPMS sensors or rotate the vehicle’s tires,
the identication codes need to be matched to
the new tire/wheel position. The sensors are
matched, to the tire/wheel positions, in the
following order: driver side front tire, passenger
side front tire, passenger side rear tire, and driver
side rear tire using a TPMS diagnostic tool.
See your dealer for service.
The TPMS sensors may also be matched to each
tire/wheel position by increasing or decreasing
the tire’s air pressure. When increasing the tire’s
pressure, do not exceed the maximum ination
pressure indicated on the tire’s sidewall.
You have two minutes to match each tire and
wheel position. If it takes longer than two minutes
to match any tire and wheel position, the
matching process stops and you need to
start over.The TPMS matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to RUN with the
engine off.
3. Press the Remote Keyless Entry (RKE)
transmitter’s Lock and Unlock buttons at
the same time for approximately ve seconds.
The horn sounds twice to signal the receiver
is in relearn mode and the TPMS sensor
matching process can begin.
4. Start with the driver’s side front tire.
5. Remove the valve cap from the tire’s valve
stem. Activate the TPMS sensor by
increasing or decreasing the tire’s air
pressure for ten seconds, or until a horn
chirp sounds. The horn chirp, which
may take up to 30 seconds to sound,
conrms that the sensor identication code
has been matched to the tire/wheel
position. To decrease the tire’s air-pressure
use the pointed end of the valve cap,
a pencil-style air pressure gage, or a key.
412