2007 PONTIAC GRAND PRIX ECO mode

Power Door Locks
To lock or unlock all
doors from inside the
vehicle, use the
power door lock switch
located on either
front door.
Move the switch on the driver’s door to the right to
lock or to the left to unlock the doors. Move the
switch on the passenger’s door to the left to lock or
to the right to unlock the doors.
If the vehicle has the content theft-deterrent
system, the vehicle may be programmed to arm
the system with the power door lock switch.
See “Lock Switch Arm” underDIC Vehicle
Customization on page 226for more information
on programming the system.
Delayed Locking
This feature delays the locking of the vehicle’s
doors for ve seconds after the last door is closed.
Two chimes will sound when the power door
lock switch or the LOCK button on the remote
keyless entry transmitter is pressed when a door
is open. The chimes indicate that the delayed
locking feature is on.
The doors can be locked immediately by pressing
the power door lock switch or the LOCK button
on the transmitter a second time.
The delayed locking feature will not activate when
the ignition is in RUN or ACC.
You can program this feature on or off through the
Driver Information Center (DIC) See “Personal
Programming Mode Screens” underDIC Vehicle
Customization on page 226.
Driver’s Side
94

Disarming with Your Key
The alarm system will disarm when the key is
used to unlock the doors. The red light will stop
ashing when the system is disarmed. If you would
like the key to disarm the alarm system, see
“Personal Programming Mode Screens” underDIC
Vehicle Customization on page 226for more
information.
PASS-Key®III
Your PASS-Key®III system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry
Canada.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
Changes or modications to this system by other
than an authorized service facility could void
authorization to use this equipment.
PASS-Key®III uses a radio frequency transponder
in the key that matches a decoder in your
vehicle.
102

To Use the Engine Coolant Heater
1. Turn off the engine.
2. Open the hood and unwrap the electrical
cord. The cord is located above the engine
air cleaner/lter. SeeEngine Compartment
Overview on page 346for more information on
location.
3. Plug the cord into a normal, grounded
110-volt AC outlet.
{CAUTION:
Plugging the cord into an ungrounded
outlet could cause an electrical shock.
Also, the wrong kind of extension cord
could overheat and cause a re. You
could be seriously injured. Plug the cord
into a properly grounded three-prong
110-volt AC outlet. If the cord will not
reach, use a heavy-duty three-prong
extension cord rated for at least 15 amps.4. Before starting the engine, be sure to unplug
and store the cord as it was before, making
sure to keep it away from moving engine parts.
If this is not done, the cord could be damaged.
How long should the coolant heater be kept
plugged in? The answer depends on the outside
temperature, the kind of oil that is in the vehicle,
and some other things. Instead of trying to list
everything here, we ask that you contact your
dealer in the area where the vehicle will be parked.
The dealer can give you the best advice for that
particular area.
Active Fuel Management™
Your vehicle’s engine may be equipped with
Active Fuel Management™. This system allows
the engine to operate on either all or half of
its cylinders, depending on your driving conditions.
When less power is required, such as cruising
at a constant vehicle speed, the system will
operate in the half cylinder mode, allowing your
vehicle to achieve better fuel economy. When
greater power demands are required, such
as accelerating from a stop, passing, or merging
onto a freeway, the system will maintain
full-cylinder operation.
109

4. Push either paddle once to up-shift to the next
gear. Pull either paddle once to down-shift to
the next gear.
The vehicle will begin moving in rst gear upon
acceleration. For better control in icy or slippery
conditions, the vehicle may start out in
SECOND (2), rather than FIRST (1). This
will only occur if you have “tapped up” to
second gear.
The up-shift light on the
instrument panel cluster,
or the up-shift symbol on
the HUD, if equipped, is
given as a prompt to use
the TAP-Shift
®paddle.
For more information, seeUp-Shift Light on
page 175.
The up-shift light will only appear in the instrument
panel cluster if the HUD is off or if the vehicle
does not have HUD.This prompt to up-shift, as needed, will be given
throughout acceleration. If up-shifting does not
occur when prompted, the vehicle speed will be
limited to protect the engine.
The gear position will display on the DIC and
HUD, if equipped, when in manual mode.
Pressing the accelerator while driving in the
highest gear (FOURTH (4)) between 20 mph
(32 km/h) and 50 mph (80 km/h), will make
the transaxle automatically downshift. As your
speed gets closer to 50 mph (80 km/h), you
will need to increase accelerator pedal travel to
get the vehicle to downshift. At 50 mph (80 km/h),
even with the accelerator fully depressed, the
transaxle will always remain in FOURTH (4). The
transaxle will also automatically downshift as
the vehicle decelerates and comes to a stop.
If a paddle is pushed or pulled and the vehicle
cannot respond to a transaxle gear change,
a chime will sound. The system will not allow either
an up-shift or a down-shift if the vehicle speed
is too fast or too slow, nor will it allow a start from
THIRD (3) or higher gear.
114

6(Low Speed):Push the lever up to the
second position for steady wiping cycles at a slow
speed.
1(High Speed):Push the lever up to the
third position for steady wiping cycles at a high
speed.
7(Mist):For a single wiping cycle, push the
lever down once and let go. The wipers will
stop after one cycle. For additional cycles, hold
the lever down.
About 30 seconds after the wipers are on, the
headlamps, taillamps, and instrument panel
lighting will come on, and the Driver Information
Center (DIC) back lighting will decrease to
the night time mode. About ten seconds after the
wipers are turned off, all the lamps will go back
to the AUTO (Automatic) mode. SeeExterior
Lamps on page 144.
Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
The windshield washer button is located at the
end of the windshield wiper lever.
K(Washer Fluid):Press this button to activate
the washer uid to spray onto the windshield.
The wipers will run for a few cycles to clear the
windshield. For more wash cycles, press and hold
the button.
If the vehicle is low on washer uid, the LOW
WASHER FLUID message will appear on
the Driver Information Center (DIC) display. See
“LOW WASHER FLUID” underDIC Warnings
and Messages on page 200for more information.
139

Entry Lighting
The entry lighting feature turns the interior lights
on before anyone enters the vehicle. The
interior lamps will come on for 40 seconds when
the doors are unlocked using the remote
keyless entry transmitter and the ignition is in
OFF. After 40 seconds have elapsed, the interior
lamps will slowly fade out. The lamps will fade
out before 40 seconds have elapsed if one of the
following is done:
Lock all doors using the remote keyless entry
transmitter.
Lock the doors using the power door lock
switch.
When any door is opened, entry lighting is
cancelled. The interior lamps will stay on while
any door is opened and slowly fade out when all
doors are closed. The interior lamps may stay
on for up to 25 seconds after all doors have been
closed if they have not been locked.
Delayed Entry Lighting
The delayed lighting feature will continue to light
the interior of the vehicle for 25 seconds after
all the doors have been closed. Delayed lighting
will not occur while the ignition is in RUN or ACC.
After 25 seconds have elapsed, the interior
lamps will slowly fade out. The lamps will fade out
before the 25 seconds have elapsed if one of
the following is done:
The ignition is turned to RUN or ACC.
The doors are locked using the remote keyless
entry transmitter.
The doors are locked using the power door
lock switch.
To turn the delayed lighting feature off or on, see
“Personal Programming Modes” underDIC
Vehicle Customization on page 226DIC Controls
and Displays.
148

Delayed Exit Lighting
For exiting the vehicle at night, the vehicle is
equipped with the delayed exit lighting feature. After
the key is removed from the ignition, the interior
lamps will light for up the amount of seconds set in
the Driver Information Center (DIC). See “Personal
Programming Mode Screens” underDIC Vehicle
Customization on page 226. After the set time has
elapsed, the interior lamps will slowly fade. The
lamps will fade before the set time has elapsed if
one of the following is done:
The ignition is turned to RUN or ACC.
The doors are locked using the remote keyless
entry transmitter.
The doors are locked using the power door lock
switch.
When any door is opened, delayed exit lighting is
cancelled. The interior lamps will stay on while
any door is opened and will slowly fade out when
all the doors are closed. The interior lamps will
stay on for the set time after all the doors
have been closed if they have not been locked.
To turn the delayed exit lighting feature off or on,
see “Personal Programming Mode Screens”
underDIC Vehicle Customization on page 226.
Front Reading Lamps
If the vehicle has a sunroof, there are reading
lamps in front of the sunroof switch located on the
headliner. These lamps will come on when the
doors are opened. Press the side of each reading
lamp to turn them on and off when the doors
are closed.
Overhead Console Reading Lamps
The vehicle may have reading lamps on the
overhead console. These lamps will turn on when
the doors are opened. When the doors are
closed, press the side of each lamp to turn them
on and off.
Rear Assist Handle Reading Lamps
If the vehicle has a reading lamp on each rear
assist handle, press the side of each lamp to turn
it on or off.
149

Fan
9
(Fan):Turn the knob by this symbol, located on
the left side of the climate control panel, clockwise
or counterclockwise to increase or decrease the fan
speed. The fan speed will be temporarily reduced
between the transition to a new mode. The fan will
resume the original speed when the transition to the
new mode is complete.
9(Off):Turn the knob to this position to turn the
climate control system off. Only the heated seat
and/or rear defrost can be operated when the fan
is off.
Mode
Turn the middle knob to select the following modes:
H(Vent) (Outside Air):This mode directs
outside air to the instrument panel outlets. If driving
in city traffic, and the vehicle is stopped and
idling, or the weather is hot, press the recirculation
button. To prevent the air inside the vehicle
from becoming stale, be sure to turn off
recirculation periodically.
)(Bi-Level):This mode directs half of the air to
the instrument panel outlets, and the remaining
air to the oor outlets. Some air may be directed
toward the windshield. Slightly cooler air is directed
to the instrument panel outlets and warmer air is
directed to the oor outlets.
6(Floor):This mode directs most of the air to
the oor outlets with some air directed toward
the side window outlets and a little air directed to
the windshield.
In this mode, the system will automatically use
outside air. The air conditioning compressor will
be engaged unless the outside temperature
is 40°F (4°C) or below.
Recirculation cannot be selected when in this
mode even though the indicator light comes on
when the recirculation button is pressed.
The middle knob on the climate control panel can
also be used to select the defog or defrost mode.
158