2007 NISSAN TIIDA window

DLK-290
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK AND UNLOCK SWITCH
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK PASSENGER DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector (A) M18 terminals 6,
25 and passenger door lock/unlock switch connector (B) D105
terminals 1, 2.
4. Check continuity between BCM connector (A) M18 terminals 6, 25 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
3.CHECK PASSENGER DOOR LOCK AND UNLOCK SWITCH GROUND
Te r m i n a l
Signal
(Reference value) (+)
(–) Power window and door lock/
unlock switch (passenger side)
connectorTe r m i n a l
D1051
Ground
2
JPMIA0154GB
ALKIA0830ZZ
BCM connector TerminalPassenger door lock
and unlock switch
connectorTerminal Continuity
M186
D1051
Ye s
25 2
BCM connector Terminal
GroundContinuity
M186
No
25

DOOR LOCK AND UNLOCK SWITCH
DLK-291
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Check continuity between power window and door lock/unlock
switch (passenger side) connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check signal between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch
Refer to DLK-292, "
PASSENGER SIDE : Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace power window and door lock/unlock switch (passenger side). Refer to XX-XX, "*****"
.
ALKIA0831ZZ
Power window and door lock/unlock switch
(passenger side) connectorTe r m i n a l
GroundContinuity
D105 3 Yes
ALKIA0739ZZ
Te r m i n a l
Signal
(Reference value) (+)
(–)
BCM connector Terminal
M186
Ground
25
JPMIA0154GB

DLK-292
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK AND UNLOCK SWITCH
6.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
PASSENGER SIDE : Component InspectionINFOID:0000000001530498
1.CHECK DOOR LOCK AND UNLOCK SWITCH
Check continuity between power window and door lock/unlock
switch (passenger side) terminals.
Is the inspection result normal?
YES >> Power window and door lock/unlock switch (passenger side) is OK.
NO >> Replace power window and door lock/unlock switch (passenger side). Refer to XX-XX, "*****"
.
WIIA1108E
Door lock and unlock switch Terminals Condition Continuity
D1051
3LOCK Yes
NEUTRAL/UNLOCK No
2UNLOCK Yes
NEUTRAL/LOCK No

INSTRUMENT PANEL WARNING LAMP ASSEMBLY
DLK-293
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
INSTRUMENT PANEL WARNING LAMP ASSEMBLY
DescriptionINFOID:0000000001396732
The door lock and unlock switch indicates door lock status. The indicator will illuminate when a lock operation
is accomplished, and during this status, if any door is opened, the indicator will turn OFF.
Component Function CheckINFOID:0000000001396733
1.CHECK FUNCTION
With CONSULT-III
Check “DOOR LOCK IND” in “Active Test” mode with CONSULT-III.
Is the inspection result normal?
YES >> Door lock and unlock switch is OK.
NO >> Refer to DLK-293, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001396734
1.CHECK DOOR LOCK AND UNLOCK SWITCH INDICATOR INPUT SIGNAL
Lock and unlock the door lock system using the main power window and door lock/unlock switch.
Does the door lock system operate properly?
YES >> GO TO 2.
NO >> Repair the power door lock system. Refer to DLK-286, "
DRIVER SIDE :
ComponentFunctionCheck".
2.CHECK DOOR LOCK AND UNLOCK SWITCH INDICATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Open and keep the driver door open for the duration of this test.
3. Disconnect instrument panel warning lamp assembly.
4. Check voltage between instrument panel warning lamp assem-
bly connector M37 terminals 3 and 5.
Is the inspection result normal?
YES >> Replace instrument panel warning lamp.
NO >> GO TO 3.
Test item Condition
DOOR LOCK IND:ON Illuminated
:OFF Not illuminated
ALKIA0832ZZ
Instrument panel warning lamp assembly connector
ConditionVo l ta g e
(Approx.)
Te r m i n a l s
3 (+) 5(-)Press the door lock switch to the
LOCK positionBattery voltage
Press the door lock switch to the
UNLOCK position0

DOOR LOCK ACTUATOR
DLK-337
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
2. Check continuity between BCM connector (A) M20 terminals 67,
77 and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to XX-XX, "*****".
NO >> Repair or replace harness.
BACK DOOR
BACK DOOR : DescriptionINFOID:0000000001530332
Locks/unlocks the door with the signal from BCM.
BACK DOOR : Component Function CheckINFOID:0000000001530333
1.CHECK FUNCTION
1. Unlock all doors using main power window and door lock/unlock switch.
2. Press the back door opener switch.
Does the back door open?
YES >> Door lock actuator is OK.
NO >> GO TO 2.
2.CHECK FUNCTION
With CONSULT-III
Check back door opener request switch “BK DOOR OPNR SW” in “Data Monitor” mode.
Is the inspection result normal?
YES >> Refer to DLK-337, "BACK DOOR : Diagnosis Procedure".
NO >> Refer to XX-XX, "*****"
.
BACK DOOR : Diagnosis ProcedureINFOID:0000000001530334
1.CHECK BACK DOOR LOCK ACTUATOR SIGNAL
1. Ensure the door lock system is in the unlock position.
2. Turn ignition switch OFF.
3. Press the back door opener switch while checking voltage
between BCM connector M20 terminals 68 and ground.
BCM connector Terminals Continuity
M2067
Ground No
77
ALKIA0777ZZ
Monitor item Condition
BD/TR OPNR SWBack door opener request switch is pressed :ON
Back door opener request switch is released :OFF
ALKIA0765ZZ

DLK-426
< SYMPTOM DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
WARNING FUNCTION SYMPTOMS
WARNING FUNCTION SYMPTOMS
BUZZER (COMBINATION METER)
BUZZER (COMBINATION METER) : Symptom TableINFOID:0000000001530564
BUZZER (COMBINATION METER) OPERATION MALFUNCTION
NOTE:
 Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
 Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconfirm the list above twice in order to ensure proper operation. Refer to DLK-39, "
System Description".
 Door lock function is normal.
Symptom Table
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER : Symptom TableINFOID:0000000001530565
INTELLIGENT KEY WARNING BUZZER OPERATION MALFUNCTION
NOTE:
 Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconfirm the list above twice in order to ensure proper operation. Refer to DLK-39, "
System Description".
Symptom Table
Symptom Diagnosis/service procedure Reference page
Ignition knob return forgotten warning does not
operate properly.1. Check buzzer (combination meter).DLK-145
2. Check intermittent incident.XX-XX, "*****"
Ignition key warning does not operate properly.1. Check buzzer (combination meter).DLK-1452. Check intermittent incident.XX-XX, "*****"
OFF position warning does not operate properly.1. Check buzzer (combination meter).DLK-1452. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Take away through
window 1. Check buzzer (combination meter).DLK-145
2. Check intermittent incident. XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Take away warning does
not operate properly.Any door open to all
doors closed.1.Check “TAKE OUT FROM WINDOW WARN” setting
in “WORK SUPPORT”.DLK-53
2. Check Intelligent Key warning buzzer.DLK-142
3. Check intermittent incident. XX-XX, "*****"

WARNING FUNCTION SYMPTOMS
DLK-427
< SYMPTOM DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
IGNITION KNOB SWITCH DOES NOT TURN ON
IGNITION KNOB SWITCH DOES NOT TURN ON : Symptom TableINFOID:0000000001530566
WARNING LAMP OPERATION MALFUNCTION
NOTE:
 Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
 Intelligent Key is registered.
 Key is not inserted in ignition switch.
 One or more registered Intelligent Keys are in the vehicle.
Symptom Table
KEY WARNING LAMP (GREEN) ILLUMINATES
Conditions of Vehicle (Operating Conditions)
 Intelligent Key is registered.
 Key is not inserted in ignition switch.
 One or more registered Intelligent Keys are in the vehicle.
KEY WARNING LAMP (RED) ILLUMINATES
Conditions of Vehicle (Operating Conditions)
Door lock operation warn-
ing chime does not oper-
ate properly.Request switch oper-
ation1. Check Intelligent Key warning buzzer.DLK-1422. Check intermittent incident.XX-XX, "*****"
Intelligent Key button
operation1. Check Intelligent Key warning buzzer.DLK-142
2. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Symptom Diagnosis/service procedureReference
page
OFF position warning does not operate properly.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Any door open to all
doors closed.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Door is open1. Check LOCK warning lamp. (RED blinking)DLK-1472. Check intermittent incident.XX-XX, "*****"
Take away through
window1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Intelligent Key low battery warning does not oper-
ate properly.1.Check “LOW BAT OF KEY FOB WARN” setting in
“WORK SUPPORT”.DLK-532. Check Intelligent Key battery.XX-XX, "*****"
3. Check KEY warning lamp. (GREEN blinking)DLK-146
4. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedure Reference page
Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (green) illuminates].1. Check steering lock solenoid.DLK-134
2. Replace Intelligent Key unit.SEC-79

WARNING FUNCTION SYMPTOMS
DLK-429
< SYMPTOM DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
 Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconfirm the list above twice in order to ensure proper operation. Refer to DLK-39, "
System Description".
 Door lock function is normal.
Symptom Table
BACK DOOR
BACK DOOR : Symptom TableINFOID:0000000001530568
BACK DOOR OPEN WARNING OPERATION MALFUNCTION
NOTE:
 Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
 Door lock function and back door opener function is normal.
Symptom Table
Symptom Diagnosis/service procedureReference
page
OFF position warning does not operate properly.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Any door open to all
doors closed.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Door is open1. Check LOCK warning lamp. (RED blinking)DLK-1472. Check intermittent incident.XX-XX, "*****"
Take away through
window1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Intelligent Key low battery warning does not oper-
ate properly.1.Check “LOW BAT OF KEY FOB WARN” setting in
“WORK SUPPORT”.DLK-532. Check Intelligent Key battery.XX-XX, "*****"
3. Check KEY warning lamp. (GREEN blinking)DLK-146
4. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Back door open warning does not operate properly.1. Check back door opener switch.DLK-98
2. Check intermittent incident.XX-XX, "*****"