Page 652 of 5883
DOOR LOCK AND UNLOCK SWITCH
DLK-63
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
2. Check signal between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch
Refer to DLK-63, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace door lock and unlock switch. Refer to XX-XX, "*****"
.
6.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
Component InspectionINFOID:0000000001396523
1.CHECK DOOR LOCK AND UNLOCK SWITCH
Check continuity between main power window and door lock/unlock
switch terminals.
ALKIA0739ZZ
Te r m i n a l
Signal
(Reference value) (+)
(–)
BCM connector Terminal
M186
Ground
25
JPMIA0154GB
ALKIA0740ZZ
Page 653 of 5883
DLK-64
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR LOCK AND UNLOCK SWITCH
Is the inspection result normal?
YES >> Main power window and door lock/unlock switch is OK.
NO >> Replace main power window and door lock/unlock switch. Refer to XX-XX, "*****"
.
Door lock and unlock switch Terminals Condition Continuity
D7, D86
17UNLOCK Yes
NEUTRAL/LOCK No
18LOCK Yes
NEUTRAL/UNLOCK No
Page 703 of 5883
![NISSAN TIIDA 2007 Service Repair Manual DLK-114
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR LOCK ACTUATOR
2. Check continuity between BCM connector (A) M20 terminals 67,
77 and ground.
Is the inspection result normal?
YES NISSAN TIIDA 2007 Service Repair Manual DLK-114
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR LOCK ACTUATOR
2. Check continuity between BCM connector (A) M20 terminals 67,
77 and ground.
Is the inspection result normal?
YES](/manual-img/5/57395/w960_57395-702.png)
DLK-114
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR LOCK ACTUATOR
2. Check continuity between BCM connector (A) M20 terminals 67,
77 and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to XX-XX, "*****".
NO >> Repair or replace harness.
BACK DOOR
BACK DOOR : DescriptionINFOID:0000000001507394
Locks/unlocks the door with the signal from BCM.
BACK DOOR : Component Function CheckINFOID:0000000001507395
1.CHECK FUNCTION
1. Unlock all doors using main power window and door lock/unlock switch.
2. Press the back door opener switch.
Does the back door open?
YES >> Door lock actuator is OK.
NO >> GO TO 2.
2.CHECK FUNCTION
With CONSULT-III
Check back door opener request switch “BK DOOR OPNR SW” in “Data Monitor” mode.
Is the inspection result normal?
YES >> Refer to DLK-114, "BACK DOOR : Diagnosis Procedure".
NO >> Refer to XX-XX, "*****"
.
BACK DOOR : Diagnosis ProcedureINFOID:0000000001507396
1.CHECK BACK DOOR LOCK ACTUATOR SIGNAL
1. Ensure the door lock system is in the unlock position.
2. Turn ignition switch OFF.
3. Press the back door opener switch while checking voltage
between BCM connector M20 terminals 68 and ground.
BCM connector Terminals Continuity
M2067
Ground No
77
ALKIA0777ZZ
Monitor item Condition
BD/TR OPNR SWBack door opener request switch is pressed :ON
Back door opener request switch is released :OFF
ALKIA0765ZZ
Page 786 of 5883
![NISSAN TIIDA 2007 Service Repair Manual WARNING FUNCTION SYMPTOMS
DLK-197
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
WARNING FUNCTION SYMPTOMS
BUZZER (COMBINATION METER)
BUZZER (COMBINATION METER) NISSAN TIIDA 2007 Service Repair Manual WARNING FUNCTION SYMPTOMS
DLK-197
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
WARNING FUNCTION SYMPTOMS
BUZZER (COMBINATION METER)
BUZZER (COMBINATION METER)](/manual-img/5/57395/w960_57395-785.png)
WARNING FUNCTION SYMPTOMS
DLK-197
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
WARNING FUNCTION SYMPTOMS
BUZZER (COMBINATION METER)
BUZZER (COMBINATION METER) : Symptom TableINFOID:0000000001396657
BUZZER (COMBINATION METER) OPERATION MALFUNCTION
NOTE:
Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconfirm the list above twice in order to ensure proper operation. Refer to DLK-39, "
System Description".
Door lock function is normal.
Symptom Table
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER : Symptom TableINFOID:0000000001396658
INTELLIGENT KEY WARNING BUZZER OPERATION MALFUNCTION
NOTE:
Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconfirm the list above twice in order to ensure proper operation. Refer to DLK-39, "
System Description".
Symptom Table
Symptom Diagnosis/service procedure Reference page
Ignition knob return forgotten warning does not
operate properly.1. Check buzzer (combination meter).DLK-145
2. Check intermittent incident.XX-XX, "*****"
Ignition key warning does not operate properly.1. Check buzzer (combination meter).DLK-1452. Check intermittent incident.XX-XX, "*****"
OFF position warning does not operate properly.1. Check buzzer (combination meter).DLK-1452. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Take away through
window 1. Check buzzer (combination meter).DLK-145
2. Check intermittent incident. XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Take away warning does
not operate properly.Any door open to all
doors closed.1.Check “TAKE OUT FROM WINDOW WARN” setting
in “WORK SUPPORT”.DLK-53
2. Check Intelligent Key warning buzzer.DLK-142
3. Check intermittent incident. XX-XX, "*****"
Page 787 of 5883
![NISSAN TIIDA 2007 Service Repair Manual DLK-198
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
IGNITION KNOB SWITCH DOES NOT TURN ON
IGNITION KNOB SWITCH DOES NOT TURN ON : Symptom TableINFOID:00000000015233 NISSAN TIIDA 2007 Service Repair Manual DLK-198
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
IGNITION KNOB SWITCH DOES NOT TURN ON
IGNITION KNOB SWITCH DOES NOT TURN ON : Symptom TableINFOID:00000000015233](/manual-img/5/57395/w960_57395-786.png)
DLK-198
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
IGNITION KNOB SWITCH DOES NOT TURN ON
IGNITION KNOB SWITCH DOES NOT TURN ON : Symptom TableINFOID:0000000001523328
WARNING LAMP OPERATION MALFUNCTION
NOTE:
Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
Intelligent Key is registered.
Key is not inserted in ignition switch.
One or more registered Intelligent Keys are in the vehicle.
Symptom Table
KEY WARNING LAMP (GREEN) ILLUMINATES
Conditions of Vehicle (Operating Conditions)
Intelligent Key is registered.
Key is not inserted in ignition switch.
One or more registered Intelligent Keys are in the vehicle.
KEY WARNING LAMP (RED) ILLUMINATES
Conditions of Vehicle (Operating Conditions)
Door lock operation warn-
ing chime does not oper-
ate properly.Request switch oper-
ation1. Check Intelligent Key warning buzzer.DLK-1422. Check intermittent incident.XX-XX, "*****"
Intelligent Key button
operation1. Check Intelligent Key warning buzzer.DLK-142
2. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Symptom Diagnosis/service procedureReference
page
OFF position warning does not operate properly.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Any door open to all
doors closed.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Door is open1. Check LOCK warning lamp. (RED blinking)DLK-1472. Check intermittent incident.XX-XX, "*****"
Take away through
window1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Intelligent Key low battery warning does not oper-
ate properly.1.Check “LOW BAT OF KEY FOB WARN” setting in
“WORK SUPPORT”.DLK-532. Check Intelligent Key battery.XX-XX, "*****"
3. Check KEY warning lamp. (GREEN blinking)DLK-146
4. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedure Reference page
Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (green) illuminates].1. Check steering lock solenoid.DLK-134
2. Replace Intelligent Key unit.SEC-79
Page 789 of 5883
![NISSAN TIIDA 2007 Service Repair Manual DLK-200
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconf NISSAN TIIDA 2007 Service Repair Manual DLK-200
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconf](/manual-img/5/57395/w960_57395-788.png)
DLK-200
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
Warning chime functions operating conditions are extremely complicated. During operation confirmations,
reconfirm the list above twice in order to ensure proper operation. Refer to DLK-39, "
System Description".
Door lock function is normal.
Symptom Table
BACK DOOR
BACK DOOR : Symptom TableINFOID:0000000001396660
BACK DOOR OPEN WARNING OPERATION MALFUNCTION
NOTE:
Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
Door lock function and back door opener function is normal.
Symptom Table
Symptom Diagnosis/service procedureReference
page
OFF position warning does not operate properly.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Any door open to all
doors closed.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Door is open1. Check LOCK warning lamp. (RED blinking)DLK-1472. Check intermittent incident.XX-XX, "*****"
Take away through
window1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Intelligent Key low battery warning does not oper-
ate properly.1.Check “LOW BAT OF KEY FOB WARN” setting in
“WORK SUPPORT”.DLK-532. Check Intelligent Key battery.XX-XX, "*****"
3. Check KEY warning lamp. (GREEN blinking)DLK-146
4. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Back door open warning does not operate properly.1. Check back door opener switch.DLK-98
2. Check intermittent incident.XX-XX, "*****"
Page 813 of 5883
DLK-224
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR
1. Open and support the back door.
2. Slightly loosen the hinge nuts.
3. Reposition the door as necessary and tighten the nuts.
4. Confirm the adjustment. Repeat as necessary to obtain the desired fit.
Striker Adjustment
1. Back door assembly 2. Back door hinge 3. Tail lamp assembly
4. Back window glass 5. Roof 6. Rear pillar
A. 6.0 ± 1.0 mm (0.24 ± 0.04 in) B. -0.5 ± 1.0 mm (-0.02 ± 0.04 in) C. 5.0 ± 1.2 mm (0.20 ± 0.05 in)
D. 0.0 ± 1.5 mm (0.0 ± 0.06 in) E. 5.0 ± 2.3 mm ( 0.20 ± 0.9 in) F. 2.7 +1.6 -2.1 mm (0.11 + 0.06 - 0.08 in)
G. 5.0 ± 1.2 mm ( 0.20 ± 0.05 in) H. 0.0 ± 1.5 mm (0.0 ± 0.06 in)
LIIA2668E
Page 819 of 5883
![NISSAN TIIDA 2007 Service Repair Manual DLK-230
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Parts LocationINFOID:0000000001315860
Removal and InstallationINFOID:0000000001315861
REM NISSAN TIIDA 2007 Service Repair Manual DLK-230
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Parts LocationINFOID:0000000001315860
Removal and InstallationINFOID:0000000001315861
REM](/manual-img/5/57395/w960_57395-818.png)
DLK-230
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Parts LocationINFOID:0000000001315860
Removal and InstallationINFOID:0000000001315861
REMOVAL
1. Remove front door finisher. Refer to INT-13, "Removal and Installation" .
2. Fully close front door window.
3. Remove the front door sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
4. Remove front door rear glass run channel. Refer to GW-14, "
Removal and Installation" .
5. Remove the cables from the holder.
6. Remove inside handle bolt, and slide the handle toward the rear
of the vehicle. disengage the handle from the door panel, and
remove the inside handle.
7. Disengage the handle from the door panel, and remove the inside handle.
1. Front door 2. Inside handle 3. Inside handle cable
4. Door lock assembly 5. Outside handle cable 6. TORX bolt (T30)
7. Key cylinder connecting rod 8. Grommet 9. TORX bolt (T30)
10. Rear gasket 11. Door key cylinder assembly
(Driver's side)
Outside handle escutcheon
(passenger's side)12. Outside handle
13. Front gasket 14. Lock knob cable 15. Holder
16. Outside handle bracket
PIIB6523E
PIIB6524E