2007 NISSAN TIIDA Air filter

EM-18
< ON-VEHICLE MAINTENANCE >[HR16DE]
AIR CLEANER FILTER
AIR CLEANER FILTER
Removal and InstallationINFOID:0000000001381387
REMOVAL
1. Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2. Pull up the air cleaner cover (1) and remove it (C).
3. Remove air cleaner filter (1) and holder (2) assembly from the
air cleaner case.
4. Remove the air cleaner filter (1) from the holder (2).
INSPECTION AFTER REMOVAL
It is necessary to clean air cleaner filter or replace it at the recommended intervals, more often under dusty
conditions. Refer to MA-7, "
Periodic Maintenance".
 Blow air into the back side of air cleaner filter until no objects spray
out.
INSTALLATION
Installation is in the reverse order of removal.
 Install the air cleaner cover (1) in the direction shown.
PBIC3557J
PBIC3558J
SMA384C
2 : Air cleaner filter
3 : Holder
PBIC3559J

AIR CLEANER AND AIR DUCT
EM-27
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
AIR CLEANER AND AIR DUCT
Exploded ViewINFOID:0000000001381395
Removal and InstallationINFOID:0000000001381396
REMOVAL
1. Remove the battery. Refer to PG-6, "Removal and Installation".
2. Remove the air duct (inlet).
3. Remove the air cleaner filter from the air cleaner case. Refer to EM-18, "
Removal and Installation".
4. Remove the air duct [between air duct (inlet) and air cleaner case] from the air cleaner case.
5. Remove the PCV hose.
6. Remove the air duct (between air cleaner case and electronic throttle control actuator).
 Add marks as necessary for easier installation.
7. Disconnect harness connector from mass air flow sensor.
8. Remove air cleaner case.
9. Remove the mass air flow sensor from the air cleaner case, if necessary.
CAUTION:
 Handle mass air flow sensor carefully and avoid impacts.
 Never touch sensor part.
INSTALLATION
Installation is in the reverse order of removal.
1. Air cleaner filter 2. Mass air flow sensor 3. O-ring
4. Holder 5. Air cleaner cover 6. Air duct
7. PCV hose 8. Clip 9. Air duct (Inlet)
10. Grommet 11. Air duct 12. Grommet
13. Air cleaner case
A. To electronic throttle control actuator B. To rocker cover
PBIC3645E

EM-40
< ON-VEHICLE REPAIR >[HR16DE]
OIL PAN (LOWER)
OIL PAN (LOWER)
Exploded ViewINFOID:0000000001381406
Removal and InstallationINFOID:0000000001381407
REMOVAL
1. Drain engine oil. Refer to LU-7, "Draining".
2. Remove the oil pan (lower) with the following procedure.
a. Loosen bolts in the reverse of the order shown.
b. Insert the seal cutter [SST: KV10111100] between oil pan
(upper) and oil pan (lower).
CAUTION:
 Be careful not to damage the mating surface.
 A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off
using a flat- bladed screwdriver, etc.
1. Rear oil seal 2. O-ring 3. Oil pan (upper)
4. Chain tensioner 5. Oil pump drive chain 6. Crankshaft sprocket
7. Oil pump sprocket 8. Oil pan drain plug 9. Washer
10. Oil pan (lower) 11. Oil filter stud bolt 12. Oil filter
13. Oil level sensor
A. Refer to EM-50
B. Refer to LU-9C. Oil pan side
JPBIA0553GB
: Engine front
PBIC4345E

EM-42
< ON-VEHICLE REPAIR >[HR16DE]
OIL PAN (UPPER) AND OIL STRAINER
OIL PAN (UPPER) AND OIL STRAINER
ComponentINFOID:0000000001532078
Removal and InstallationINFOID:0000000001532079
NOTE:
The oil strainer and oil pump are included in the oil pan (upper). Individual disassembly is prohibited.
REMOVAL
NOTE:
When removing oil pan (lower) only, steps “2” and “3” are not necessary. Perform step “5” after completing
step “4”.
1. Remove engine undercover using power tool.
2. Remove engine and transaxle assembly from the vehicle, and then separate engine and transaxle. Refer
to EM-89, "
Removal and Installation".
3. Install engine assembly to widely use engine stand. Refer to EM-94, "
Setting".
4. Drain engine oil. Refer to LU-7, "
Draining".
5. Remove the oil pan (lower) using the following procedure.
1. Rear oil seal 2. O-ring 3. Oil pan (upper)
4. Chain tensioner 5. Oil pump drive chain 6. Crankshaft sprocket
7. Oil pump sprocket 8. Oil pan drain plug 9. Washer
10. Oil pan (lower) 11. Oil filter stud bolt 12. Oil filter
13. Oil level sensor
A. Refer to EM-50
B. Refer to LU-9C. Oil pan side
JPBIA0553GB

CAMSHAFT
EM-59
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
CAMSHAFT
Exploded ViewINFOID:0000000001381414
Removal and InstallationINFOID:0000000001381415
CAUTION:
The rotation direction in the text indicates all directions seen from the engine front.
REMOVAL
1. Remove front wheel (RH). Refer to WT-6, "Rotation".
2. Remove front fender protector (RH). Refer to EXT-22, "
Removal and Installation".
3. Drain engine oil. Refer to LU-7, "
Draining".
CAUTION:
Be sure to perform this step when engine is cold.
4. Remove the following parts.
 Intake manifold: Refer to EM-29, "
Exploded View".
 Drive belt: Refer to EM-16, "
Removal and Installation".
 Water pump pulley: Refer to CO-20, "
Exploded View".
 Ground cable (RH)
1. Camshaft bracket (No. 2 to 5) 2. Camshaft bracket (No.1) 3. Camshaft sprocket (EXH)
4. Camshaft sprocket (INT) 5. Cylinder head 6. Oil filter (for intake valve timing control)
7. Washer 8. Plug 9. Intake valve timing control solenoid valve
10. O-ring 11. O-ring 12. Camshaft position sensor (PHASE)
13. Valve lifter 14. Camshaft (INT) 15. Camshaft (EXH)
A. Refer to EM-59
PBIC3672E

EM-64
< ON-VEHICLE REPAIR >[HR16DE]
CAMSHAFT
15. Remove the camshaft (INT) (1) and the camshaft sprocket (INT)
(2) with the following procedure.
a. Keeping the camshaft hexagonal part (A) still with the wrench,
loosen the bolts for the camshaft sprocket (INT) (2).
b. Disassemble the camshaft (1) from the camshaft sprocket (INT)
(2).
c. Remove camshaft (INT).
CAUTION:
Never damage the signal plate of rear end.
16. Remove valve lifter.
 Identify installation positions, and store them without mixing them up.
17. Remove intake valve timing control solenoid valve (1).
18. Remove the generator and bracket, remove the plug (2), and
then remove the oil filter. Refer to CHG-15, "
Removal and Instal-
lation".
INSTALLATION
AWBIA0108ZZ
1 :Camshaft (INT)
AWBIA0109ZZ
AWBIA011 0ZZ
PBIC3692E

CAMSHAFT
EM-65
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
1. Install the oil filter (1).
 The oil filter is assembled to the plug (3), and then install it to
the cylinder head.
2. Install intake valve timing control solenoid valve.
 Insert it straightly into the cylinder head.
 Tighten bolts after placing it completely.
3. Install valve lifter.
 If it is reused, install in its original positions.
4. Put a matching mark for positioning the camshaft (INT) and the camshaft sprocket (INT) with the following
procedure.
NOTE:
It prevents the knock pin from engaging with the incorrect pin hole after installing the camshaft (INT) and
the camshaft sprocket (INT).
a. Put the matching marks (A) on a line extending from the knock
pin position of camshaft (INT) (1) front surface.
 Put the marks on the visible position with the camshaft
sprocket installed. (Example shown)
b. Put the matching marks on a line extending from the knock pin
hole (B) position of camshaft sprocket (INT) (2). (Example
shown)
 Put the marks on the visible position with it installed to the
camshaft.
5. Install camshaft.
 Distinction between camshaft (INT and EXH) is performed with
the different shapes of rear end.
 Install camshafts to the cylinder head so that knock pins (A) on
front end are positioned as shown.
NOTE:
Though camshaft does not stop at the portion as shown, for the
placement of cam nose, it is generally accepted camshaft is
placed for the same direction.
2: Washer
PBIC3695E
PBIC3696E
1 : Camshaft (EXH)
2 : Camshaft (INT)
A : Identification mark
PBIC3698E
1 : Camshaft (EXH)
2 : Camshaft (INT)
: Upper side
PBIC3699E

CAMSHAFT
EM-71
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
c. Tighten bolts in the numerical order shown.
d. After all bolts are tightened, retighten them to specified torque in
numerical order as shown.
CAUTION:
Be sure to wipe off any excessive liquid gasket leaking to
surface.
22. Insert crankshaft pulley by aligning with crankshaft key.
 When inserting crankshaft pulley with a plastic hammer, tap on its center portion (not circumference).
CAUTION:
Never damage front oil seal lip section.
23. Tighten crankshaft pulley bolt with the following procedure:
 Secure crankshaft pulley with a suitable tool, and tighten crankshaft pulley bolt.
a. Apply new engine oil to thread and seat surfaces of crankshaft pulley bolt.
b. Tighten crankshaft pulley bolt.
c. Put a paint mark (B) on crankshaft pulley, mating with any one of
six easy to recognize angle marks (A) on crankshaft bolt flange
(1).
d. Turn another 60 degrees clockwise (angle tightening).
 Check the tightening angle with movement of one angle mark.
24. Make sure that crankshaft turns smoothly by rotating by hand clockwise.
25. Install the camshaft position sensor (PHASE) to the rear end of cylinder head.
 Tighten bolts with it seated completely.
26. Check and adjust valve clearance. Refer to EM-21, "
Inspection and Adjustment".
27. Installation is in the reverse order of removal, for the remaining parts.
InspectionINFOID:0000000001381416
INSPECTION AFTER REMOVAL
Oil Filter
KBIA3429J
: 35.0 N·m (3.6 kg-m, 26 ft-lb)
PBIC3726E