2007 NISSAN TIIDA Body

DLK-746
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
DOOR
1.
Removal and InstallationINFOID:0000000001732060
FRONT DOOR
CAUTION:
 When removing and installing the front door assembly, support the door with a jack and cloth to pro-
tect the door and body.
 When removing and installing front door assembly, be sure to carry out the fitting adjustment. Refer
to DLK-743, "
Fitting Adjustment".
 After installing, apply touch-up paint onto the head of the hinge nuts.
 Check the hinge rotating part for lubrication. If necessary, apply “body grease”.
 Operate with two workers, because of its heavy weight.
 Check front door open/close operation after installation.
Removal
1. Remove dash side finisher. Refer to INT-20, "Removal and Installation".
2. Disconnect the front door harness connectors.
3. Remove the front door harness grommet, and then remove the
harness from the vehicle.
4. Remove the check link bolt.Striker bolts 20 N·m (2.2 kg-m, 16 ft-lb)
LIIA2641E
PIIB6518E
14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB6543E

DOOR
DLK-747
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
5. Remove the hinge nuts and then the door assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
CAUTION:
 When removing and installing the rear door assembly, support the door with a jack and cloth to pro-
tect the door and body.
 When removing and installing rear door assembly, be sure to carry out the fitting adjustment. Refer
to DLK-743, "
Fitting Adjustment".
 After installing, apply touch-up paint onto the head of the hinge nuts.
 Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
 Operate with two workers, because of its heavy weight.
 Check rear door open/close operation after installation.
Removal
1. Remove the rear door harness grommet.
2. Disconnect the rear door harness connector. 24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB6519E
PIIB6520E
PIIB6521E

TRUNK LID
DLK-759
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
3. Remove the nuts (a) and the trunk lid assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing, apply touch-up paint (body color) to the head of the hinge nuts.
Trunk Lid LockINFOID:0000000001732069
REMOVAL
1. Remove the trunk lid finisher. Refer to XX-XX, "*****".
2. If equipped, disconnect the trunk lid lock cylinder rod.
3. Remove the release cable.
4. Disconnect the electrical connector (a), remove the bolts (b) and
the trunk lid lock (1).
INSTALLATION
Installation is in the reverse order of removal.
Trunk Lid StrikerINFOID:0000000001732070
REMOVAL
1. Remove the trunk rear plate and trunk rear finisher. Refer to XX-XX, "*****".
2. Remove the bolts, disconnect the electrical connector and remove the trunk lock actuator.
3. Remove the bolt and disconnect the trunk lid release cable.
LIIA2933E
LIIA2935E

EC-332
< ECU DIAGNOSIS >[HR16DE (WITH EURO-OBD)]
ECM
3GroundLG/RHeated oxygen sensor 1
heaterOutput[Engine is running]
 Warm up condition
 Engine speed: Below 3,600
rpmApproximately 3.2V
[Engine is running]
 Warm-up condition
 Idle speed
[Engine is running]
 Engine speed: Above 3,600
rpmBATTERY VOLTAGE (11 - 14V)
4GroundPThrottle control motor
(Close)Output[Ignition switch: ON]
 Engine stopped
 Shift lever: D (A/T) or 1st (M/
T)
 Accelerator pedal: Fully re-
leased0 - 14V
5GroundRHeated oxygen sensor 2
heaterOutput[Engine is running]
 Engine speed: Below 3,900
rpm after the following con-
ditions are met
- Engine: after warming up
- Keeping the engine speed
between 3,500 and 4,000
rpm for 1 minute and at idle
for 1 minute under no load10V
[Ignition switch: ON]
 Engine stopped
[Engine is running]
 Engine speed: Above 3,900
rpmBATTERY VOLTAGE
(11 - 14V)
9GroundW/BEVAP canister purge volume
control solenoid valveOutput[Engine is running]
 Idle speedBATTERY VOLTAGE
(11 - 14V)
[Engine is running]
 Engine speed: About 2,000
rpm (More than 100 sec-
onds after starting engine.)BATTERY VOLTAGE
(11 - 14V)
10
11GroundB
B/WECM ground —[Engine is running]
 Idle speedBody ground Te r m i n a l N o .
Wire
colorDescription
ConditionVa l u e
(Approx.)
+ -– Signal nameInput/
OutputPBIA8148J
PBIA8149J
PBIA8148J
PBIB0050E
PBIB0520E

ECM
EC-337
< ECU DIAGNOSIS >[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O93 Ground W/L Ignition switch Input[Ignition switch: OFF] 0V
[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
94 Ground V ASCD steering switch Input[Ignition switch: ON]
 ASCD steering switch: OFF4V
[Ignition switch: ON]
 CANCEL switch: Pressed1V
[Ignition switch: ON]
 MAIN switch: Pressed0V
[Ignition switch: ON]
 RESUME/ACCELERATE
switch: Pressed3V
[Ignition switch: ON]
 SET/COAST switch:
Pressed2V
95 Ground BSensor ground
(ASCD steering switch)—[Engine is running]
 Warm-up condition
 Idle speed0V
99 Ground R/W Stop lamp switch Input[Ignition switch: OFF]
 Brake pedal: Fully released0V
[Ignition switch: OFF]
 Brake pedal: Slightly de-
pressedBATTERY VOLTAGE
(11 - 14V)
100 Ground R ASCD brake switch Input[Ignition switch: ON]
 Brake pedal: Slightly de-
pressed (A/T)
 Brake pedal and clutch ped-
al: Slightly depressed (M/T)0V
[Ignition switch: ON]
 Brake pedal: Fully released
(A/T)
 Brake pedal and/or clutch
pedal: Fully released (M/T)BATTERY VOLTAGE
(11 - 14V)
102 Ground BRSensor power supply
(Accelerator pedal position
sensor 2)— [Ignition switch: ON] 5V
103 Ground GRAccelerator pedal position
sensor 2Input[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully re-
leased0.3 - 0.6V
[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully de-
pressed1.95 - 2.4V
104 Ground YSensor ground
(Accelerator pedal position
sensor 2)—[Engine is running]
 Warm-up condition
 Idle speed0V
105 Ground G Power supply for ECM Input [Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
106 Ground VSensor power supply
(Accelerator pedal position
sensor 1)— [Ignition switch: ON] 5V
108 Ground B ECM ground —[Engine is running]
 Idle speedBody ground Terminal No.
Wire
colorDescription
ConditionVa l u e
(Approx.)
+ -– Signal nameInput/
Output

EC-374
< PRECAUTION >[HR16DE (WITH EURO-OBD)]
PRECAUTIONS
When measuring ECM signals with a circuit tester, never allow
the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.
Do not use ECM ground terminals when measuring input/out-
put voltage. Doing so may result in damage to the ECM’s tran-
sistor. Use a ground other than ECM terminals, such as the
ground.
Do not operate fuel pump when there is no fuel in lines.
Tighten fuel hose clamps to the specified torque.
Do not depress accelerator pedal when starting.
Immediately after starting, do not rev up engine unnecessar-
ily.
Do not rev up engine just prior to shutdown.
When installing C.B. ham radio or a mobile phone, be sure to
observe the following as it may adversely affect electronic
control systems depending on installation location.
-Keep the antenna as far as possible from the electronic con-
trol units.
-Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Do not let them run parallel for a long distance.
-Adjust the antenna and feeder line so that the standing-wave
ratio can be kept smaller.
-Be sure to ground the radio to vehicle body.
SEF348N
SEF709Y
SEF708Y

ECM
EC-639
< ECU DIAGNOSIS >[HR16DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
4GroundPThrottle control motor
(Close)Output[Ignition switch: ON]
 Engine stopped
 Shift lever: D (A/T) or 1st (M/
T)
 Accelerator pedal: Fully re-
leased0 - 14V
5GroundRHeated oxygen sensor 2
heaterOutput[Engine is running]
 Engine speed: Below 3,900
rpm after the following con-
ditions are met
- Engine: after warming up
- Keeping the engine speed
between 3,500 and 4,000
rpm for 1 minute and at idle
for 1 minute under no load10V
[Ignition switch: ON]
 Engine stopped
[Engine is running]
 Engine speed: Above 3,900
rpmBATTERY VOLTAGE
(11 - 14V)
9GroundW/BEVAP canister purge volume
control solenoid valveOutput[Engine is running]
 Idle speedBATTERY VOLTAGE
(11 - 14V)
[Engine is running]
 Engine speed: About 2,000
rpm (More than 100 sec-
onds after starting engine.)BATTERY VOLTAGE
(11 - 14V)
10
11GroundB
B/WECM ground —[Engine is running]
 Idle speedBody ground
15 Ground G/L Throttle control motor relay Output[Ignition switch: OFF]BATTERY VOLTAGE
(11 - 14V)
[Ignition switch: ON] 0 - 1.0V Terminal No.
Wire
colorDescription
ConditionVa l u e
(Approx.)
+ -– Signal nameInput/
Output
PBIA8149J
PBIA8148J
PBIB0050E
PBIB0520E

EC-644
< ECU DIAGNOSIS >[HR16DE (WITHOUT EURO-OBD)]
ECM
93 Ground W/L Ignition switch Input[Ignition switch: OFF] 0V
[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
94 Ground V ASCD steering switch Input[Ignition switch: ON]
 ASCD steering switch: OFF4V
[Ignition switch: ON]
 CANCEL switch: Pressed1V
[Ignition switch: ON]
 MAIN switch: Pressed0V
[Ignition switch: ON]
 RESUME/ACCELERATE
switch: Pressed3V
[Ignition switch: ON]
 SET/COAST switch:
Pressed2V
95 Ground BSensor ground
(ASCD steering switch)—[Engine is running]
 Warm-up condition
 Idle speed0V
99 Ground R/W Stop lamp switch Input[Ignition switch: OFF]
 Brake pedal: Fully released0V
[Ignition switch: OFF]
 Brake pedal: Slightly de-
pressedBATTERY VOLTAGE
(11 - 14V)
100 Ground R ASCD brake switch Input[Ignition switch: ON]
 Brake pedal: Slightly de-
pressed (A/T)
 Brake pedal and clutch ped-
al: Slightly depressed (M/T)0V
[Ignition switch: ON]
 Brake pedal: Fully released
(A/T)
 Brake pedal and/or clutch
pedal: Fully released (M/T)BATTERY VOLTAGE
(11 - 14V)
102 Ground BRSensor power supply
(Accelerator pedal position
sensor 2)— [Ignition switch: ON] 5V
103 Ground GRAccelerator pedal position
sensor 2Input[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully re-
leased0.3 - 0.6V
[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully de-
pressed1.95 - 2.4V
104 Ground YSensor ground
(Accelerator pedal position
sensor 2)—[Engine is running]
 Warm-up condition
 Idle speed0V
105 Ground G Power supply for ECM Input [Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
106 Ground VSensor power supply
(Accelerator pedal position
sensor 1)— [Ignition switch: ON] 5V
108 Ground B ECM ground —[Engine is running]
 Idle speedBody ground Te r m i n a l N o .
Wire
colorDescription
ConditionVa l u e
(Approx.)
+ -– Signal nameInput/
Output