2007 NISSAN TIIDA sensor

INSUFFICIENT HEATING
HAC-81
< SYMPTOM DIAGNOSIS >[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
HAC
N
O
P
INSUFFICIENT HEATING
Component Function CheckINFOID:0000000001547078
SYMPTOM: Insufficient heating
INSPECTION FLOW
1.CONFIRM SYMPTOM BY PERFORMING OPERATIONAL CHECK - TEMPERATURE DECREASE
1. Turn temperature control dial clockwise to maximum heat position.
2. Check for hot air at discharge air outlets.
Can the symptom be duplicated?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK FOR ANY SYMPTOMS
Perform a complete operational check for any symptoms. Refer to HAC-6, "
Operational Check".
Does another symptom exist?
YES >> Refer to HAC-5, "How to Perform Trouble Diagnosis For Quick and Accurate Repair" .
NO >> System OK.
3.CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4.
4.CHECK COOLANT SYSTEM
1. Check engine coolant level. Refer to XX-XX, "*****" .
2. Check hoses for leaks or kinks.
3. Check Radiator cap. Refer to XX-XX, "*****" .
OK or NG
OK >> GO TO 5.
NG >> Repair/replace as necessary.
5.CHECK AIR MIX DOOR CABLE
Check air mix door cable operation. Refer to XXXX AIR MIX DOOR CABLE ADJUSTMENT .
OK or NG
YES >> GO TO 6.
NO >> Adjust or replace air mix door cable. Refer to XXXX AIR MIX DOOR CABLE ADJUST. .
6.CHECK AIR DUCTS
Check ducts for air leaks.
OK or NG
OK >> GO TO 7.
NG >> Repair air leaks.
7.CHECK HEATER HOSE TEMPERATURES
1. Start engine and warm it up to normal operating temperature.
2. Touch both the inlet and outlet heater hoses.
Is the inlet hose hot and the outlet hose warm?
YES >> GO TO 8.
NO >> Both hoses warm: GO TO 9.
8.CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check engine control temperature sensor. Refer to XX-XX, "*****" .
OK or NG
OK >> System OK.

FUNCTION INFORMATION
HAC-89
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
C
D
E
F
G
H
J
K
L
MA
B
HAC
N
O
P
FUNCTION DIAGNOSIS
FUNCTION INFORMATION
Component Part LocationINFOID:0000000001547388
ENGINE COMPARTMENT
PASSENGER COMPARTMENT
1. Compressor (magnet clutch) F3 2. Refrigerant pressure sensor E17 3. Ambient sensor E60
AWIIA0602ZZ

HAC-90
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
FUNCTION INFORMATION
1. Variable blower control M90, M91 2. Intake door motor M89 3. In-vehicle sensor M93
4. Air mix door motor M88 5. Intake sensor M92 6. Mode door motor M87
7. Sunload sensor M94 8. Front blower motor M62 9. Front air control M50, M51
AWIIA0282ZZ

HAC-92
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
AUTOMATIC AIR CONDITIONER SYSTEM
AUTOMATIC AIR CONDITIONER SYSTEM
Control System DiagramINFOID:0000000001547392
CONTROL SYSTEM
The control system consists of input sensors, switches, the front air control (microcomputer) and outputs.
The relationship of these components is shown in the figure below:
Control System DescriptionINFOID:0000000001547393
CONTROL OPERATION
AWIIA0480ZZ
AWIIA0279GB

HAC-94
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
AUTOMATIC AIR CONDITIONER SYSTEM
MAGNET CLUTCH CONTROL
When A/C switch, AUTO switch or DEF switch is pressed, front air control inputs compressor ON signal to
BCM.
BCM sends compressor ON signal to ECM, via CAN communication line.
ECM judges whether compressor can be turned ON, based on each sensor status (refrigerant-pressure sen-
sor signal, throttle angle, etc.). If it judges compressor can be turned ON, it sends compressor ON signal to
IPDM E/R, via CAN communication line.
Upon receipt of compressor ON signal from ECM, IPDM E/R turns air conditioner relay ON to operate com-
pressor.
Discharge Air FlowINFOID:0000000001547394
AWIIA0277GB
Mode door positionAir outlet/distribution
Vent Foot Defroster
100% — —
56% 44% —
16% 64% 20%
16% 53% 31%
17% — 83%
Airflow always present at driver and passenger side demisters
WJIA2190E

HAC-98
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
SELF-DIAGNOSIS FUNCTION
SELF-DIAGNOSIS FUNCTION
Front Air Control Self-DiagnosisINFOID:0000000001547401
DESCRIPTION
The self-diagnostic system diagnoses sensors, door motors, blower motor, etc. by system line. Refer to appli-
cable sections (items) for details. Shifting from usual control to the self-diagnostic system is accomplished by
starting the engine (turning the ignition switch ON) and pressing OFF switch for at least 5 seconds. The OFF
switch must be pressed within 10 seconds after starting the engine (ignition switch is turned ON). This system
will be cancelled by either pressing AUTO switch or turning the ignition switch OFF. Shifting from one step to
another is accomplished by means of pushing front air control switches, as required.
Additionally shifting from STEP-5 to AUXILIARY MECHANISM is accomplished by means of pushing blower
motor switch (UP: ).
FUNCTION CONFIRMATION PROCEDURE
1.SET IN SELF-DIAGNOSTIC MODE
1. Turn ignition switch ON.
2. Set in self-diagnostic mode as follows. Within 10 seconds after starting engine (ignition switch is turned
ON.), press OFF switch for at least 5 seconds.
AWIIA0284GB

SELF-DIAGNOSIS FUNCTION
HAC-99
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
C
D
E
F
G
H
J
K
L
MA
B
HAC
N
O
P
CAUTION:
If battery voltage drops below 12V during diagnosis STEP-3, door motor speed becomes slower and
as a result, the system may generate an error even when operation is usual. To avoid this, start engine
before performing this diagnosis.
>> GO TO 2.
2.STEP-1: LED AND DISPLAY ARE CHECKED
Check display screen (1) and LED illumination (2).
OK or NG
OK >> GO TO 3.
NG >> Malfunction OFF switch or AUTO switch. Refer to HAC-
311, "Self-Diagnosis".
3.CHECK TO ADVANCE SELF-DIAGNOSIS STEP-2
Press temperature control switch (UP: ).
Advance to self
-diagnosis STEP-2?
YES >> GO TO 4.
NO >> Replace front air control (temperature control switch is malfunctioning). Refer to XX.
4.CHECK TO RETURN SELF-DIAGNOSIS STEP-1
Press temperature control switch (DOWN: ).
Return to self
-diagnosis STEP-1?
YES >> GO TO 5.
NO >> Replace front air control (temperature control switch is malfunctioning). Refer to XX.
5.STEP-2: SENSOR CIRCUITS ARE CHECKED FOR OPEN OR SHORT CIRCUIT
Press temperature control switch (UP: ).
Does code No. 20 appear on the display?
YES >> GO TO 6.
NO >> GO TO 13.
6.STEP-3: AIR MIX DOOR AND MODE DOOR POSITIONS ARE CHECKED
Press temperature control switch (UP: ).
Does code No. 30 appear on the display?
YES >> GO TO 7.
NO >> GO TO 14.
AWIIA0285ZZ
SJIA0737E
SJIA0738E

HAC-100
< FUNCTION DIAGNOSIS >[AUTO AIR CONDITIONER (W/O NAVI)]
SELF-DIAGNOSIS FUNCTION
7.STEP-4: OPERATION OF EACH DOOR MOTOR IS CHECKED
1. Press temperature control switch (UP: ).
2. Press (DEF) switch. Code No. of each door motor test is
indicated on the display.
>> GO TO 8.
8.CHECK ACTUATORS
Refer to HAC-94, "
Discharge Air Flow" and confirm discharge air flow, air temperature, blower motor voltage
and compressor operation.
Checks must be made visually, by listening to any noise, or by touching air outlets with your hand, etc. for
improper operation.
OK or NG
OK >> GO TO 9.
NG >>  Air outlet does not change.
Go to Mode Door Motor Circuit. Refer to HAC-109, "
Mode Door Motor Diagnosis Procedure".
 Intake door does not change.
Go to Intake Door Motor Circuit. Refer to HAC-116, "
Intake Door Motor Diagnosis Procedure".
 Blower motor operation is malfunctioning.
Go to Blower Motor Circuit. Refer to HAC-120, "
Front Blower Motor Diagnosis Procedure".
 Magnet clutch does not engage.
Go to Magnet Clutch Circuit. Refer to HAC-125, "
Magnet Clutch Diagnosis Procedure".
 Discharge air temperature does not change.
Go to Air Mix Door Motor Circuit. Refer to HAC-112, "
Air Mix Door Motor Diagnosis Procedure".
9.STEP-5: TEMPERATURE OF EACH SENSOR IS CHECKED
1. Press temperature control switch (UP: ).
2. Code No. 5 appears on the display.
>> GO TO 10.
10.CHECK AMBIENT SENSOR
RHA495A
Code No. 414243444546
Mode door position VENT B/L 1 B/L 2 FOOT D/F DEF
Intake door position REC REC 20% FRE 80% FRE FRE FRE
Air mix door position FULL COLD FULL COLD 50% 50% FULL HOT FULL HOT
Blower motor voltage 5V 10.5V 8.5V 8.5V 8.5V Battery voltage
Compressor ON ON ON OFF OFF ON
Blower motor ON signal 12V 12V 12V 1V 1V 12V