2007 NISSAN TIIDA sensor

CAMSHAFT
EM-61
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
a. Loosen bolts in the reverse of the order shown.
b. Cut liquid gasket by prying the position ( ) shown, and then
remove the front cover.
10. Remove camshaft position sensor (PHASE) from rear end of cylinder head.
CAUTION:
Handle it carefully and avoid impacts.
11. Remove camshaft sprocket (EXH) (1).
CAUTION:
 Hold the camshaft hexagonal part (A), and then secure the
camshaft.
 Never rotate crankshaft and camshaft separately, so as
not to contact valve with piston in the following steps.
12. Turn the camshaft sprocket (INT) to the most advanced position.
CAUTION:
Installation and removal of the camshaft sprocket (INT) must be done in the most advanced posi-
tion for the following reasons.
KBIA3429J
PBIC3712E
AWBIA0102ZZ

CAMSHAFT
EM-71
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
c. Tighten bolts in the numerical order shown.
d. After all bolts are tightened, retighten them to specified torque in
numerical order as shown.
CAUTION:
Be sure to wipe off any excessive liquid gasket leaking to
surface.
22. Insert crankshaft pulley by aligning with crankshaft key.
 When inserting crankshaft pulley with a plastic hammer, tap on its center portion (not circumference).
CAUTION:
Never damage front oil seal lip section.
23. Tighten crankshaft pulley bolt with the following procedure:
 Secure crankshaft pulley with a suitable tool, and tighten crankshaft pulley bolt.
a. Apply new engine oil to thread and seat surfaces of crankshaft pulley bolt.
b. Tighten crankshaft pulley bolt.
c. Put a paint mark (B) on crankshaft pulley, mating with any one of
six easy to recognize angle marks (A) on crankshaft bolt flange
(1).
d. Turn another 60 degrees clockwise (angle tightening).
 Check the tightening angle with movement of one angle mark.
24. Make sure that crankshaft turns smoothly by rotating by hand clockwise.
25. Install the camshaft position sensor (PHASE) to the rear end of cylinder head.
 Tighten bolts with it seated completely.
26. Check and adjust valve clearance. Refer to EM-21, "
Inspection and Adjustment".
27. Installation is in the reverse order of removal, for the remaining parts.
InspectionINFOID:0000000001381416
INSPECTION AFTER REMOVAL
Oil Filter
KBIA3429J
: 35.0 N·m (3.6 kg-m, 26 ft-lb)
PBIC3726E

ENGINE ASSEMBLY
EM-91
< REMOVAL AND INSTALLATION >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O Vehicle Underbody
1. Remove front wheel sensor (LH and RH) for ABS from steering knuckle. Refer to BRC-83, "Removal and
Installation".
2. Remove brake caliper assembly with piping connected from steering knuckle. Temporarily secure it on the
vehicle side with a rope to avoid load on it. Refer to BR-24, "
Component".
3. Remove drive shafts (LH and RH) from steering knuckle. Refer to FAX-7, "
Removal and Installation".
4. Remove exhaust front tube. Refer to EX-5, "
Component".
5. Remove rear torque rod.
NOTE:
A/T models shown.
6. Remove A/T cooler hoses from transmission (A/T models).
7. Preparation for the separation work of transaxle is as follows:
 Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to EM-89, "
Exploded
View".
Removal
1. Install engine slinger to cylinder head front left side (A) and rear
right side (B) and support the engine with a hoist.
2. Lift with a hoist and secure the engine in appropriate position.
3. Use a suitable tool to securely support bottom of the engine and
the transaxle assembly and simultaneously adjust hoist tension.
CAUTION:
Put a piece of wood or something similar as the supporting
surface, secure a completely stable condition.
PBIC3737E
PBIC3738E
PBIC3223J

EM-96
< DISASSEMBLY AND ASSEMBLY >[HR16DE]
OIL PAN (UPPER)
OIL PAN (UPPER)
Exploded ViewINFOID:0000000001381430
Removal and InstallationINFOID:0000000001381431
NOTE:
The oil strainer and oil pump are included in the oil pan (upper). Individual disassembly is prohibited.
REMOVAL
1. Remove the oil pan (lower). Refer to EM-40, "Exploded View".
2. Remove front cover and timing chain. Refer to EM-50, "
Exploded View".
3. Remove oil pump sprocket and crankshaft sprocket together with oil pump drive chain. Refer to EM-50,
"Exploded View".
4. Remove oil pan (upper) with the following procedure.
1. Rear oil seal 2. O-ring 3. Oil pan (upper)
4. Chain tensioner 5. Oil pump drive chain 6. Crankshaft sprocket
7. Oil pump sprocket 8. Oil pan drain plug 9. Washer
10. Oil pan (lower) 11. Oil filter stud bolt 12. Oil filter
13. Oil level sensor
A. Refer to EM-50
B. Refer to LU-9C. Oil pan side
JPBIA0553GB

OIL PAN (UPPER)
EM-97
< DISASSEMBLY AND ASSEMBLY >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
a. Loosen oil pan (upper) mounting bolts in the reverse of the order
shown in the figure.
b. Insert a flat-bladed offset screwdriver into the arrow ( ) in the
figure and open up a crack between the oil pan (upper) cylinder
block.
c. Insert the seal cutter [SST: KV10111100] between remove the oil
pan (upper) and cylinder block. Slide seal cutter by tapping on
the side of tool with a hammer.
CAUTION:
 Be careful not to damage the mating surface.
 A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off using a screwdriver, etc. outside the
indicated location.
 Never remove oil pump and oil strainer from oil pan (upper).
5. Remove oil level sensor, if necessary.
6. Remove rear oil seal from crankshaft.
INSTALLATION
1. Install the oil pan (upper) in the following procedure.
a. Use scraper to remove old liquid gasket from mating surfaces.
 Also remove the old liquid gasket from mating surface of cylinder block.
 Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surfaces when cleaning off old liquid gasket.
b. Install O-ring to the cylinder block.
: Engine front
MBIB1374E
: Engine front
MBIB1375E

EM-100
< DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
CYLINDER BLOCK
Exploded ViewINFOID:0000000001381433
1. Crankshaft position sensor (POS) cover 2. Crankshaft position sensor (POS) 3. O-ring
4. Water drain plug 5. Cylinder block 6. Oil level gauge
7. Oil level gauge guide 8. O-ring 9. Knock sensor
AWBIA0153GB

CYLINDER BLOCK
EM-101
< DISASSEMBLY AND ASSEMBLY >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
Disassembly and AssemblyINFOID:0000000001381434
DISASSEMBLY
1. Remove oil pan (upper). Refer to EM-96, "Removal and Installation".
2. Remove cylinder head. Refer to EM-80, "
Removal and Installation".
3. Remove knock sensor.
CAUTION:
Carefully handle knock sensor avoiding shocks.
4. Remove crankshaft position sensor (POS) and cover.
CAUTION:
 Avoid impacts such as a dropping.
 Never disassemble.
 Keep it away from metal particles.
 Never place the sensor where it is exposed to magnetism.
5. Remove piston and connecting rod assembly with the following procedure:
 Before removing piston and connecting rod assembly, check the connecting rod side clearance. Refer to
EM-108, "
Inspection".
a. Position crankshaft pin corresponding to connecting rod to be removed onto the bottom dead center.
b. Remove connecting rod cap.
c. Using a hammer handle or similar tool, push piston and connect-
ing rod assembly out to the cylinder head side.
CAUTION:
 Be careful not to damage matching surface with connect-
ing rod cap.
 Be careful not to damage the cylinder wall and crankshaft
pin, resulting from an interference of the connecting rod
big end.
6. Remove connecting rod bearings.
CAUTION:
Identify installation positions, and store them without mixing up.
7. Remove piston rings form piston.
 Before removing piston rings, check the piston ring side clearance. Refer to EM-108, "
Inspection".
 Use a piston ring expander (commercial service tool) (A).
CAUTION:
 When removing piston rings, be careful not to damage
the piston.
 Be careful not to damage piston rings by expanding
them excessively.
10. Oil pressure switch 11. Top ring 12. Second ring
13. Oil ring 14. Piston pin 15. Piston
16. Connecting rod 17. Connecting rod bearing (upper) 18. Main bearing (upper)
19. Thrust bearing 20. Crankshaft key 21. Connecting rod cap bolt
22. Connecting rod cap 23. Connecting rod bearing (lower) 24. Main bearing (lower)
25. Crankshaft 26. Signal plate 27. Rear oil seal
28. Flywheel 29. Main bearing cap bolt 30. Main bearing cap
A. Refer to EM-101
KBIA3365J
PBIC3233J

EM-108
< DISASSEMBLY AND ASSEMBLY >[HR16DE]
CYLINDER BLOCK
18. Install knock sensor (1).
 Install connectors so that they are positioned towards the rear
of the engine.
CAUTION:
 Never tighten mounting bolt while holding the connector.
 If any impact by dropping is applied to knock sensor,
replace it with a new one.
NOTE:
 Make sure that there is no foreign material on the cylinder
block mating surface and the back surface of knock sensor.
 Make sure that knock sensor does not interfere with other parts.
19. Install crankshaft position sensor (POS) and cover.
 Tighten bolts with it seated completely.
20. For the oil level gauge guide (1), fix the position (B) shown in the
figure to the water inlet clip (A) after inserting to the cylinder
block side.
21. Assemble in the reverse order of disassembly after this step.
InspectionINFOID:0000000001381435
CRANKSHAFT END PLAY
 Measure the clearance between thrust bearings and crankshaft
arm when crankshaft is moved fully forward or backward with a dial
indicator (A).
 If the measured value exceeds the limit, replace thrust bearings,
and measure again. If it still exceeds the limit, replace crankshaft
also.
CONNECTING ROD SIDE CLEARANCE
 Measure the side clearance between connecting rod and crank-
shaft arm with a feeler gauge (A).
 If the measured value exceeds the limit, replace connecting rod,
and measure again. If it still exceeds the standard, replace crank-
shaft also.
PISTON TO PISTON PIN OIL CLEARANCE
Piston Pin Hole Diameter
: Engine front
PBIC3754E
PBIC3755E
Standard and Limit : Refer to EM-127, "Cylinder Block".
PBIC3762E
Standard : Refer to EM-127, "Cylinder Block".
PBIC3763E