2007 NISSAN 350Z ad blue

[x] Cancel search: ad blue

set clock instrument cluster clock setting emergency towing instrument panel tires

Page 77 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Workshop Manual CAMSHAFT
EM-77
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
INSTALLATION
1. Install timing chain tensioners (secondary) (1) on both sides of
cylinder head.
Install timing chain tensione

Page 99 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Workshop Manual CYLINDER HEAD
EM-99
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
VALVE SEAT CONTACT
After confirming that the dimensions of valve guides and valves
are within the specifications, perfor

CYLINDER HEAD
EM-99
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
VALVE SEAT CONTACT
After confirming that the dimensions of valve guides and valves
are within the specifications, perform this procedure.
Apply prussian blue (or white lead) onto contacting surface of
valve seat to check the condition of the valve contact on the sur-
face.
Check if the contact area band is continuous all around the cir-
cumference.
If not, grind to adjust valve fitting and check again. If the contact-
ing surface still has “NG” conditions even after the re-check,
replace valve seat. Refer to EM-99, "
VALVE SEAT REPLACE-
MENT" .
VALVE SEAT REPLACEMENT
When valve seat is removed, replace with Oversize (Service) [0.5 mm (0.020 in)] valve seat.
1. Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess
in cylinder head. Set the machine depth stop to ensure this. Refer to EM-141, "
Va l v e S e a t" .
CAUTION:
Prevent to scratch cylinder head by excessive boring.
2. Ream cylinder head recess diameter for service valve seat.
Be sure to ream in circles concentric to valve guide center.
This will enable valve to fit correctly.
3. Heat cylinder head to 110 to 130°C (230 to 266°F) by soaking in
heated oil.
4. Provide valve seats cooled well with dry ice. Force fit valve seat into cylinder head.
WARNING:
Avoid directly touching cold valve seats.
Cylinder head contains heat. When working, wear protective equipment to avoid getting burned.
5. Using valve seat cutter set (commercial service tool) or valve
seat grinder, finish seat to the specified dimensions. Refer to
EM-141, "
Valve Seat" .
CAUTION:
When using valve seat cutter, firmly grip cutter handle with
both hands. Then, press on the contacting surface all
around the circumference to cut in a single drive. Improper
pressure on with cutter or cutting many different times may
result in stage valve seat.
SBIA0322E
Oversize (Service) [0.5 mm (0.020 in)]
Intake : 38.500 - 38.516 mm (1.5157 - 1.5164 in)
Exhaust : 32.100 - 32.116 mm (1.2638 - 1.2644 in)
SEM795A
SEM008A
SEM934C

Page 122 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Workshop Manual EM-122
CYLINDER BLOCK
Revision: 2006 November2007 350Z
Undersize Bearings Usage Guide
When the specified connecting rod bearing oil clearance is not obtained with standard size connecting rod
bearing

Page 124 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Workshop Manual EM-124
CYLINDER BLOCK
Revision: 2006 November2007 350Z
Main Bearing Grade Table (All Journals)
Undersize Bearing Usage Guide
When the specified main bearing oil clearance is not obtained with standar

Page 146 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Workshop Manual EM-146
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2006 November2007 350Z
*: Total indicator reading
MAIN BEARING
Undersize
Unit: mm (in) Center distance “r”40.66 - 40.74 (1.6008 - 1.6039)
Out

Page 147 of 148

NISSAN 350Z 2007 Z33 Engine Mechanical Workshop Manual SERVICE DATA AND SPECIFICATIONS (SDS)
EM-147
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
Main Bearing Oil Clearance
Unit: mm (in)
*: Actual clearance
CONNECTING ROD BEARING
Undersize
Un

lug pattern OBD port wheel radio controls brake rotor adblue reset