2007 NISSAN 350Z engine oil

EM-38
FUEL INJECTOR AND FUEL TUBE
Revision: 2006 November2007 350Z

When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretched while it was being attached, do not insert it
quickly into fuel tube.

Insert O-ring straight into fuel injector. Do not decenter or twist it.
4. Install fuel injector to fuel tube as follows:
a. Insert clip (3) into clip mounting groove (D) on fuel injector (5).
CAUTION:

Do not reuse clip. Replace it with a new one.

Be careful to keep clip from interfering with O-ring. If
interference occurs, replace O-ring.
b. Insert fuel injector (5) into fuel tube (1) with clip attached.

Insert it while matching it to the axial center.

Insert fuel injector (5) so that protrusion (A) of fuel tube
matches cutout (B) of clip (3).

Make sure that fuel tube flange (E) is securely fixed in flange
fixing groove (C) on clip (3).
c. Make sure that installation is complete by checking that fuel
injector does not rotate or come off.

Make sure that protrusions of fuel injectors are aligned with
cutouts of clips after installation.
5. Install fuel tube and fuel injector assembly to intake manifold.
CAUTION:
Be careful not to let tip of injector nozzle come in contact with other parts.

Tighten mounting bolts in two steps in numerical order as
shown in the figure.
6. Connect fuel injector harness connector.
7. Connect fuel feed hose (with damper).

Handling procedure of O-ring is the same as that of fuel damper and fuel sub-tube.

Insert fuel damper straight into fuel sub-tube.

Tighten mounting bolts evenly in turn.

After tightening mounting bolts, make sure that there is no gap between flange and fuel sub-tube.
8. Connect quick connector between fuel feed hose (with damper) and centralized under-floor piping con-
nection as follows:
a. Make sure no foreign substances are deposited in and around centralized under-floor piping and quick
connector, and no damage on them.
b. Thinly apply new engine oil around centralized under-floor piping from tip end to spool end.
c. Align center to insert quick connector straightly into centralized under-floor piping.
2 : O-ring (Black)
4 : O-ring (Green)
PBIC5042E
: Engine front
1st step
: 10.1 N·m (1.0 kg-m, 7 ft-lb)
2nd step
: 23.6 N·m (2.4 kg-m, 17 ft-lb)
PBIC4963E

EM-40
ROCKER COVER
Revision: 2006 November2007 350Z
ROCKER COVERPFP:13264
Removal and InstallationNBS0000P

Refer to GI-11, "Components" for symbol marks in the figure.
REMOVAL
1. Remove engine cover. Refer to EM-17, "INTAKE MANIFOLD COLLECTOR" .
2. Remove intake manifold collector. Refer to EM-17, "
INTAKE MANIFOLD COLLECTOR" .
3. Separate engine harness removing their brackets from rocker covers.
4. Remove ignition coil. Refer to EM-31, "
IGNITION COIL" .
1. PCV hose 2. Clamp 3. Ignition coil
4. Spark plug 5. PCV valve 6. O-ring
7. Rocker cover gasket (right bank) 8. Rocker cover (right bank) 9. O-ring
10. Camshaft position sensor (bank 1) 11.Exhaust valve timing control posi-
tion sensor (bank 1)12. Camshaft position sensor (bank 2)
13.Exhaust valve timing control position
sensor (bank 2)14. Rocker cover gasket (left bank) 15. Rocker cover (left bank)
16. PCV hose 17. Oil catcher 18. Oil filler cap
19. PCV hose
A. To intake manifold collector B. Refer to EM-40
C. Camshaft bracket side
D. To air duct
PBIC4964E

ROCKER COVER
EM-41
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
5. Remove camshaft position sensor and exhaust valve timing
control position sensor.
CAUTION:

Handle carefully to avoid dropping and shocks.

Do not disassemble.

Do not allow metal powder to adhere to magnetic part at
sensor tip.

Do not place sensors in a location where they are exceed
to magnetism.
6. Remove PCV hoses from rocker covers.
7. Remove PCV valve and O-ring from rocker cover, if necessary.
8. Remove oil filler cap from rocker cover, if necessary.
9. Loosen mounting bolts with power tool in reverse order as
shown in the figure.
10. Remove rocker cover gaskets from rocker covers.
11. Use scraper to remove all trances of liquid gasket from cylinder head and camshaft bracket (No. 1).
CAUTION:
Do not scratch or damage the mating surface when cleaning off old liquid gasket.
A : Keep off any magnetic materials
PBIC5150E
: Engine front
PBIC4990E

EM-42
ROCKER COVER
Revision: 2006 November2007 350Z
INSTALLATION
1. Apply liquid gasket with tube presser [SST: WS39930000 ( —
)] to joint part among rocker cover, cylinder head and cam-
shaft bracket (No. 1) as follows:
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-45, "
RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS" .
NOTE:
The figure shows an example of left bank side [zoomed in
shows camshaft bracket (No. 1)].
a. Refer to the figure “a” to apply liquid gasket to joint part of cam-
shaft bracket (No. 1) and cylinder head.
b. Refer to the figure “b” to apply liquid gasket to the figure “a”
squarely.
2. Install new rocker cover gasket to rocker cover.
3. Install rocker cover.

Check if rocker cover gasket is not dropped from installation groove of rocker cover.
4. Tighten bolts in two steps separately in numerical order as
shown in the figure.
5. Install oil filler cap to rocker cover (left bank), if removed.
6. Install new O-ring and PCV valve to rocker cover (right bank), if removed.
7. Install PCV hose.

Insert PCV hose by 25 to 30 mm (0.98 to 1.18 in) from connector end.

When installing, be careful not to twist or come in contact with other parts.
PBIC2474E
: Engine front
1st step
: 2.0 N·m (0.2 kg-m, 18 in-lb)
2nd step
: 8.3 N·m (0.85 kg-m, 73 in-lb)
PBIC4990E

EM-44
FRONT TIMING CHAIN CASE
Revision: 2006 November2007 350Z
FRONT TIMING CHAIN CASEPFP:13599
Removal and InstallationNBS0000Q
NOTE:

This section describes removal/installation procedure of front timing chain case and timing chain related
parts without removing oil pan (upper) on vehicle.

When oil pan (upper) needs to be removed or installed, or when rear timing chain case is removed or
installed, remove oil pans (upper and lower) first. Then remove front timing chain case, timing chain
related parts, and rear timing chain case in this order, and install in the reverse order of removal. Refer to
EM-53, "
TIMING CHAIN" .

Refer to EM-53, "TIMING CHAIN" for component parts location.
REMOVAL
1. Remove engine cover with power tool. Refer to EM-17, "INTAKE MANIFOLD COLLECTOR" .
2. Remove undercover with power tool.
3. Release the fuel pressure. Refer to EC-79, "
FUEL PRESSURE RELEASE" .
4. Disconnect the battery cable from the negative terminal.
5. Drain engine oil. Refer to LU-7, "
Changing Engine Oil" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine oil on drive belts.
6. Drain engine coolant from radiator. Refer to CO-10, "
Changing Engine Coolant" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belts.
7. Remove radiator cooling fan assembly. Refer to CO-21, "
COOLING FAN" .
8. Separate engine harnesses removing their brackets from front timing chain case.
9. Remove drive belts. Refer to EM-12, "
DRIVE BELTS" .
10. Remove intake manifold collector. Refer to EM-17, "
INTAKE MANIFOLD COLLECTOR" .
11. Remove harness bracket and fuel sub tube mounting bolt on front timing chain case.
12. Remove oil level gauge and guide.
13. Remove power steering oil pump from bracket with piping connected, and temporarily secure it to aside.
Refer to PS-28, "
POWER STEERING OIL PUMP" .
14. Remove power steering oil pump bracket. Refer to PS-28, "
POWER STEERING OIL PUMP" .
15. Remove alternator. Refer to SC-20, "
CHARGING SYSTEM" .
16. Remove water outlet and water piping. Refer to CO-28, "
WATER OUTLET AND WATER PIPING" .
17. Remove left and right valve timing control covers with the following procedure.
a. Disconnect valve timing control harness connector.
b. Loosen mounting bolts in reverse order as shown in the figure.
A : Right bank
B : Left bank
C : Dowel pin hole
PBIC4965E

FRONT TIMING CHAIN CASE
EM-45
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: 2006 November2007 350Z
c. Shaft is engaged with intake side camshaft sprocket center hole
on inside. Pull straight out so as not to tilt until the joint is disen-
gaged.

The mating surface of magnet retarder may be fitted with the
exhaust side camshaft sprocket via the engine oil. Open valve
timing control cover carefully.

If the mating surface of magnet retarder is fitted with the cam-
shaft sprocket, open the cover within the range that the load is
not applied to the harness. And then, remove it so as to pre-
vent magnet retarder from dropping.
CAUTION:

Be careful not to damage magnet retarder.

When carrying valve timing control cover, face the magnet retarder side up to prevent the cover
from falling from magnet retarder.

Do not remove magnet retarder from valve timing control cover. (Disassembly prohibited parts)
18. Remove rocker covers (right and left banks). Refer to EM-40, "
ROCKER COVER" .
NOTE:
When only timing chain (primary) is removed, rocker cover does not need to be removed.
19. Obtain No. 1 cylinder at TDC of its compression stroke as follows:
NOTE:
When timing chain is not removed/installed, this step is not required.
a. Rotate crankshaft pulley clockwise to align timing mark (grooved
line without color) with timing indicator.
b. Make sure that intake and exhaust cam noses on No. 1 cylinder
(engine front side of right bank) are located as shown in the fig-
ure.

If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
NOTE:
When only timing chain (primary) is removed, rocker cover does
not need to be removed. To make sure that No. 1 cylinder is at
its compression TDC, remove front timing chain case first. Then
check mating marks on camshaft sprockets. Refer to EM-60,
"INSTALLATION" .
20. Remove crankshaft pulley as follows:
a. Remove rear cover plate and set ring gear stopper [SST:
KV10118600 (J-48641)] (A) as shown in the figure.
: Timing mark (grooved without color)
PBIC3561E
PBIC4966E
SEM418G
1 : Oil pan
2 : Fly wheel (M/T models) or drive plate (A/T models)
: Vehicle front
PBIC5051E

EM-46
FRONT TIMING CHAIN CASE
Revision: 2006 November2007 350Z
b. Loosen crankshaft pulley bolt and locate bolt seating surface as
10 mm (0.39 in) from its original position.
CAUTION:
Do not remove crankshaft pulley bolt as it will be used as a
supporting point for suitable puller.
c. Place suitable puller tab on holes of crankshaft pulley, and pull
crankshaft pulley through.
CAUTION:
Do not put suitable puller tab on crankshaft pulley periph-
ery, as this will damage internal damper.
21. Remove oil pan (lower). Refer to EM-26, "
OIL PAN AND OIL STRAINER" .
22. Loosen two mounting bolts in front of oil pan (upper) in reverse
order as shown in the figure.
23. Remove front timing chain case as follows:
a. Loosen mounting bolts in reverse order as shown in the figure.
PBIC1103E
EMQ0477D
: Engine front
PBIC4967E
PBIC4968E

EM-48
FRONT TIMING CHAIN CASE
Revision: 2006 November2007 350Z
2. Hammer dowel pins (right and left) into front timing chain case
up to a point close to taper in order to shorten protrusion length.
3. Install new front oil seal on the front timing chain case.

Apply new engine oil to both oil seal lip and dust seal lip.

Install it so that each seal lip is oriented as shown in the fig-
ure.

Using suitable drift [outer diameter: 60 mm (2.36 in)] (A),
press-fit oil seal until it becomes flush with front timing chain
case end face.

Make sure the garter spring is in position and seal lip is not
inverted.
4. Install front timing chain case as follows:
PBIC2615E
SEM715A
PBIC4971E