2007 NISSAN 350Z air condition

POWER DOOR LOCK SYSTEM
BL-49
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
2. CHECK BACK DOOR OPENER SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and back door opener switch connector.
3. Check continuity between BCM harness connector M90 terminal 30 and back door opener switch harness
connector T103 terminal 1.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between BCM and back door
opener switch.
3. CHECK BACK DOOR OPENER SWITCH
Check continuity between back door opener switch terminals 1 and 2.
OK or NG
OK >> GO TO 4.
NG >> Replace back door opener switch.
4. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect driver side door lock actuator connector.
2. Check continuity between back door opener switch harness connector T103 terminal 2 and driver side
door lock actuator harness connector D11 terminal 2.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness between back door opener
switch and driver side door lock actuator. 30 (P) – 1 (P) : Continuity should exist.
PIIB3791E
Connector Terminals Condition Continuity
T103 1 2Back door opener switch: ON Yes
Back door opener switch: OFF No
PIIA2349E
2 (G) – 2 (OR) : Continuity should exist.
PIIA2348E

BL-50
POWER DOOR LOCK SYSTEM
Revision: 2006 November2007 350Z
5. CHECK DOOR LOCK ACTUATOR GROUND CIRCUIT
Check continuity between driver side door lock actuator harness connector D11 terminal 4 and ground.
OK or NG
OK >> Replace driver side door lock actuator.
NG >> Repair or replace harness.
Check Back Door Opener Actuator NIS0000X
1. CHECK BACK DOOR OPENER ACTUATOR SIGNAL
Check voltage between BCM connector and ground.
Press the back door opener switch when driver side door is
unlocked.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK BACK DOOR OPENER ACTUATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and back door opener actuator connector.
3. Check continuity between BCM harness connector B83 terminal 68 and back door opener actuator har-
ness connector T11 terminal 1.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between BCM and back door
opener actuator. 4 (B) – Ground : Continuity should exist.
PIIA2347E
ConnectorTerminals
(Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
B83 68 (L/R) GroundBack door
opener switch
ONBattery
voltage
Back door
opener switch
OFF0
PIIB1270E
68 (L/R) – 1 (L/R) : Continuity should exist.
PIIB1263E

FUEL FILLER LID OPENER
BL-57
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
3. CHECK FUEL LID OPEN OUTPUT SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace BCM. Refer to BCS-17, "
Removal and Installation of BCM" .
4. CHECK FUEL LID OPENER ACTUATOR CIRCUIT
1. Disconnect BCM connector and fuel lid opener actuator connector.
2. Check continuity between BCM harness connector B83 terminal
70 and fuel lid opener actuator harness connector T19 terminal
1.
3. Check continuity between fuel lid opener actuator harness con-
nector T19 terminal 1 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK FUEL LID OPENER ACTUATOR GROUND CIRCUIT
Check continuity between fuel lid opener actuator harness connector
T19 terminal 2 and ground.
OK or NG
OK >> Replace fuel lid opener actuator.
NG >> Repair harness or connector.
ConnectorTerminal
(Wire color)
ConditionVoltage [V]
(Approx.)
(+) (–)
B83 70 (W/L) GroundFuel lid opener switch
ONBattery voltage
(for 0.5s)
Fuel lid opener switch
OFF0
PIIB1264E
70 (W/L) - 1 (W/L) : Continuity should exist.
1 (W/L) - ground : Continuity should not exist.
PIIB1265E
2 (B) - ground : Continuity should exist.
PIIA8090E

BL-58
FUEL FILLER LID OPENER
Revision: 2006 November2007 350Z
6. CHECK FUEL LID OPENER SWITCH
1. Disconnect fuel lid opener switch
2. Check continuity between fuel lid opener switch harness con-
nector M13 terminals 1 and 2.
OK or NG
OK >> GO TO 7.
NG >> Replace fuel lid opener switch.
7. CHECK FUEL LID OPENER SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector B83 terminal
58 and fuel lid opener switch harness connector M13 terminal 1.
3. Check continuity between BCM harness connector B83 terminal
58 (Y/B) and ground.
OK or NG
OK >> GO TO 8.
NG >> Repair harness or connector.
8. CHECK FUEL LID OPENERE SWITCH GROUND CIRCUIT
Check continuity between fuel lid opener switch harness connector
M13 terminal 2 and ground.
OK or NG
OK >> Replace fuel lid opener switch.
NG >> Repair harness or connector.
Connec-
torTerminalsFuel lid opener switch
conditionContinuity
M13 1 2ON (Pushed) Yes
OFF (Released) No
PIIA8091E
58 (Y/B) - 1 (L/R) : Continuity should exist.
58 (Y/B) - ground : Continuity should not exist.
PIIB3792E
2 (B) - ground : Continuity should exist.
PIIA8093E

BL-80
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
2. CHECK DOOR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door switch and BCM connector.
3. Check continuity between door switch harness connector B17, B23 terminal 1 and BCM harness connec-
tor B83 terminal 62 (driver side) or M90 terminal 12 (passenger side).
4. Check continuity between door switch harness connector B17,
B23 terminal 1and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace door switch harness.
3. CHECK DOOR SWITCH
Check continuity between door switch B17 (driver side) or B23 (passenger side) terminal 1 and ground part of
door switch.
OK or NG
OK >> GO TO 4.
NG >> Replace door switch.Driver side door
1 (L) - 62 (L) : Continuity should exist.
Passenger side door
1 (P) - 12 (P) : Continuity should exist.
Driver side door
switch
1 (L) - Ground : Continuity should not exist.
Passenger side door
switch
1(P) - Ground : Continuity should not exist.
PIIA9540E
TerminalCondition of door
switchContinuity
1 Ground part of door switchPushed (close) No
Released (open) Yes
PIIA3351E

BL-82
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
2. CHECK DOOR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect back door switch and BCM connector.
3. Check continuity between BCM harness connector B83 terminal 58 and back door switch harness con-
nector T12 terminal 1.
4. Check continuity between BCM harness connector B83 terminal
58 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace back door switch harness.
3. CHECK BACK DOOR SWITCH
Check continuity between back door switch terminals 1 and 3.
OK or NG
OK >> GO TO 4.
NG >> Replace back door switch.
4. CHECK BACK DOOR SWITCH GROUND CIRCUIT
Check continuity between door switch harness connector T12 terminal 3 and ground.
OK or NG
OK >> Check harness connection.
NG >> Repair or replace back door switch harness.58 (R/W) - 1 (R/W) : Continuity should exist.
58 (R/W) - Ground : Continuity should not exist.
PIIB3794E
Connector Terminal Condition of back door switch Continuity
T12 1 3Open position Yes
Closed position No
PIIA4316E
3 (B) - Ground : Continuity should exist.
PIIA2490E

REMOTE KEYLESS ENTRY SYSTEM
BL-83
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Check Trunk Lid Lock Assembly (Trunk Room Lamp Switch) / For RoadsterNIS0001N
1. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) INPUT SIGNAL
With CONSULT-III
Check trunk lid opener switch (“TRUNK OPN MNTR”) in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
Check voltage between BCM connector and ground.
*: When interior lamp battery saver control is in OFF. → Approx. 5V.
OK or NG
OK >> Trunk room lamp switch is OK.
NG >> GO TO 2.
2. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly (trunk room lamp switch) and BCM connector.
3. Check continuity between BCM harness connector B83 terminal 57 and trunk lid lock assembly (trunk
room lamp switch) harness connector T47 terminal 3.
4. Check continuity between BCM harness connector B83 terminal
57 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace trunk lid lock assembly (trunk room
lamp switch) harness.
Monitor item Condition
TRNK OPN MNTROPEN : ON
CLOSE : OFF
Con-
nectorTe r m i n a l s
(Wire color)Condition of trunk lid lock
assembly (trunk room lamp
switch)Voltage [V]
(Approx.)
(+) (–)
B83 57 (R/W) GroundOpen 0
Close Battery voltage*
PIIB1266E
57 (R/W) - 3 (R/W) : Continuity should exist.
57 (R/W) - Ground : Continuity should not exist.
PIIB9170E

BL-84
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
3. CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly (trunk room lamp switch) connector.
3. Check continuity between trunk lid lock assembly (trunk room lamp switch) connector T47 terminal 1 and
ground.
OK or NG
OK >> Check trunk lid lock assembly (trunk room lamp switch).
NG >> Repair or replace trunk lid lock assembly (trunk room
lamp switch) harness.
Check Key Switch NIS0001O
1. CHECK KEY SWITCH
Check continuity key switch terminals 1 and 2.
OK or NG
OK >> GO TO 3.
NG >> Replace key switch.
2. CHECK KEY SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
37 and key switch harness connector M25 terminal 1.
3. Check continuity between BCM harness connector M90 terminal
37 and ground.
OK or NG
OK >> Check the following.

10A fuse [No.21, located in the fuse block (J/B)]

Harness for open or short between key switch and fuse
NG >> Repair or replace harness.1 (B) - Ground : Continuity should exist.
PIIB9171E
Connector Terminals Condition of key switch Continuity
M25 1 2Inserted Yes
Removed No
PIIA2627E
37 (B/R) - 1 (B/R) : Continuity should exist.
37 (B/R) - Ground : Continuity should not exist.
PIIB1258E