TRUNK LID
BL-109
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Removal and Installation of Trunk Lid StayNIS0002F
REMOVAL
1. Screwdriver into the gap and remove holder.
2. Remove trunk lid stay.
INSTALLATION
1. Note the following, and install in the reverse order of removal.
Install holder to trunk lid stay, and then push it into trunk lid hinge (stud ball) when installing trunk lid stay.
2. After installation, check the operation.
Removal and Installation of Trunk Lid Lock Assembly NIS0002G
REMOVAL
1. Remove the trunk lid weatherstrip. Refer to BL-113, "Removal and Installation of Trunk Lid Weatherstrip" .
2. Remove trunk lid release lever. Refer to EI-49, "
Removal and Installation (for Roadstar Models)" .
3. Remove the trunk lid finisher. Refer to EI-49, "
TRUNK ROOM
TRIM & TRUNK LID FINISHER" .
4. Disconnect the release lever cable and trunk lid opener cable
from the clip.
5. After removing the harness connector, remove the mounting
bolts, and remove the trunk lid lock.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing, close the trunk lid height. Perform the lock and surface height adjustment. Refer
to BL-107, "
Fitting Adjustment" .
After installing, check the operation.
Removal and Installation of Trunk Lid StrikerNIS0002H
REMOVAL
Remove the mounting bolts, then remove the striker from the trunk
lock support.
PIIA7601E
PIIA7602E
PIIB1179E
BL-118
TRUNK LID OPENER
Revision: 2006 November2007 350Z
Terminals and Reference Value for BCMNIS0002P
Te r -
minalWire
colorItemSignal input/
outputConditionVoltage (V)
(Approx.)
18 BRemote keyless entry
receiver (Ground)—— 0
19 YRemote keyless entry
receiver (Power supply)OutputKey is inserted in IGN key cylinder 0
All door closed
20 LRemote keyless entry
receiver (Signal)InputKey is inserted in IGN key cylinder 0
Waiting
(All door closed)
When signal is received
(All door closed)
30 P Trunk lid opener switch InputTrunk lid opener
cancel switch is
ONTrunk lid opener
switch is ON0
Trunk lid opener
switch is OFF5
Driver side door is
lockedTrunk lid opener
cancel switch is
OFF5
39 L CAN – H Input/Output — —
40 P CAN – L Input/Output — —
42 GY Ignition switch (ON) Input Ignition switch ON or START position Battery voltage
52 B Ground — — 0
55 RPower source (Fusible
link)Input — Battery voltage
68 L/RTrunk lid opener release
output signalOutput Closed (OFF) → Opened (ON) 0 → Battery voltage
OCC3881D
OCC3879D
OCC3880D
BL-122
TRUNK LID OPENER
Revision: 2006 November2007 350Z
7. CHECK TRUNK LID OPENER SWITCH
1. Disconnect trunk lid opener switch
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminals 1 and 2.
OK or NG
OK >> GO TO 8.
NG >> Replace trunk lid opener switch.
8. CHECK TRUNK LID OPENER CANCEL SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
30 and trunk lid opener cancel switch harness connector B71
terminal 1.
OK or NG
OK >> GO TO 9.
NG >> Repair harness or connector.
9. CHECK TRUNK LID OPENER SWITCH CIRCUIT
Check continuity between trunk lid opener cancel switch harness
connector B71 terminal 2 and trunk lid opener switch harness con-
nector T103 terminal 1.
OK or NG
OK >> GO TO 10.
NG >> Repair harness or connector.
10. CHECK DRIVER SIDE DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect driver side door lock actuator connector.
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminal 2 and driver side door lock actuator switch
harness connector D11 terminal 2.
OK or NG
OK >> GO TO 11.
NG >> Repair harness or connector.
Te r m i n a l sTrunk lid opener switch
conditionContinuity
12ON (Pushed) Yes
OFF (Released) No
PIIA7872E
30 (P) - 1 (SB) : Continuity should exist.
PIIB1272E
2 (R/Y) - 1 (P) : Continuity should exist.
PIIA7874E
2 (G) - 2 (OR) : Continuity should exist.
PIIA7875E
BL-124
TRUNK LID OPENER
Revision: 2006 November2007 350Z
3. CHECK TRUNK LID OPENER SWITCH
1. Disconnect trunk lid opener switch
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminals 1 and 2.
OK or NG
OK >> GO TO 4.
NG >> Replace trunk lid opener switch.
4. CHECK TRUNK LID OPENER CANCEL SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M90 terminal
30 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK TRUNK LID OPENER SWITCH CIRCUIT
Check continuity between trunk lid opener cancel switch harness
connector B71 terminal 2 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK DRIVER SIDE DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect driver side door lock actuator connector.
2. Check continuity between trunk lid opener switch harness con-
nector T103 terminal 2 and ground.
OK or NG
OK >> Replace BCM.
NG >> Repair harness or connector.
Te r m i n a l sTrunk lid opener switch
conditionContinuity
12ON (Pushed) Yes
OFF (Released) No
PIIA7872E
30 (P) - ground : Continuity should not exist.
PIIB1273E
2 (R/Y) - ground : Continuity should not exist.
PIIA8096E
2 (G) - ground : Continuity should not exist.
PIIA8097E