2007 MITSUBISHI LANCER EVOLUTION oil

CIRCUIT DIAGRAMS
H1J10X10AB
B-157
OIL PRESSURE WARNING LAMP
BRAKE WARNING LAMP

INDEX - In order of connector No.C-2
Wiring diagram
page Circuit diagram page Parts name Connector
No.
AA-45Condenser fan motorB-177,183B-7,9
A-46Condenser fan motorB-177,183B-7,9
A-47A/C compressorB-178,184B-7,9
A-48Power steering oil pressure switchB-90,98B-7,9
BB-01Windshield wiper motorB-186,190B-10,14
B-02Throttle position sensorB-89,97,215,223,231,241B-10,14
B-03Vehicle speed sensorB-92,100,150,154,197B-10,14
B-04Brake fluid level switchB-157B-10,14
B-05XEngine speed detection connectorB-73,82,83,90,98B-10,14
B-06XNo connectionB-73B-10,14
B-07XNo connectionB-73B-10,14
B-08XNo connectionB-73B-10,14
B-09XIgnition coil relay or no
connection B-73,83B-10,14
B-10XNo connectionB-73B-10,14
B-11XEngine control relayB-73,86,94,252,254B-10,14
B-12XA/C compressor relayB-73,178,184B-10,14
B-14Control wiring harness and battery
wiring harness combinationB-79,84,91,99,157B-10,14
B-18StarterB-79B-11,15
B-19StarterB-79B-11,15
B-20Oil pressure switchB-157B-11,15
B-21AlternatorB-84B-11,15
B-22AlternatorB-84B-11,15
B-23Purge control solenoid valveB-91,99B-11,15
B-24Injector 4B-89,97B-11,15
B-25Injector 3B-89,97B-11,15
B-26Injector 2B-89,97B-11,15
B-27Injector 1B-89,97B-11,15
B-31Air flow sensorB-90,98B-11,15
B-34Oxygen sensorB-88,96B-11,15
B-36Waste gate solenoid valveB-91,99B-11,15
B-37Fuel pressure solenoid valveB-90,98B-11,15

INDEX - In order of connector No.C-3
Wiring diagram
page Circuit diagram page Parts name Connector
No.
BB-108Back-up lamp switchB-142,143B-12,16
B-110Engine coolant temperature gauge unitB-148,152B-12,16
B-112EGR solenoid valveB-91,99B-12,16
B-114Ignition coil 1B-82,83B-12,16
B-115Idle speed control servoB-88,96B-12,16
B-116Camshaft position sensorB-88,96B-12,16
B-118Engine coolant temperature sensorB-89,97B-12,16
B-119Ignition coil 2B-82,83B-12,16
B-121Crank angle sensorB-88,96B-13,16
B-122Detonation sensorB-89,97B-13,17
B-123ABS-ECUB-198,200,201,202,203,204,205,206,
208,209,210,211,229,232,233,239,
242,243B-13,17
B-138ResistorB-89,97B-13,17
B-139Electric pump relay B-216,224,234,244B-13,17
B-140Fuel pump relay 3B-93,101B-13,17
B-141Fuel pump resistorB-93,101B-13,17
B-142Secondary air control solenoid valveB-91,99B-13,17
CC-01Combination meterB-84,87,95,103,106,118,122,126,129,
135,139,148,149,152,153,156,157,
198,206,214,222,230,240,248,250,
256, 258B-18,24
C-02Combination meterB-110,115,118,122,126,129,135,139,
148,149,152,153,156,157,198,206,
248, 250,256,258B-18,24
C-03Hazard warning switchB-136,140B-18,24
C-04ClockB-194B-18,24
C-05J/C (1)B-56,62,93,101,104,107,111,112,115,
116,118,122,124,125,127,128,131,
133,136,137,140,141,148,152,153,
156,158,164,170,172,175,181,185,
187,191,194,195,196,197,212,214,
220,222,228,230,238,240,257B-18,24
C-08J/C (3)B-58,64,95,104,105,107,108,112,113,
116,117,119,123,124,125,126,127,
128,129,131,133,136,137,140,141,
149,153,159,164,165,171,172,173,
175,180,181,185,187,188,189,191,
193,194,195,202,210,214,218,222,
226,227,230,236,240,246,247,253,
255,257,258B-18,24

INDEX - In order of parts nameC-15
Wiring diagram
page Circuit diagram page Connector
No. Parts name
GG sensor (Lateral)D-33B-200,208,213,221,229,239B-31,33
G sensor (Longitudinal)D-32B-200,208,213,221,229,239B-31,33
HHazard warning switchC-03B-136,140B-18,24
Headlamp (HI:LH)A-16B-103,106B-6,8
Headlamp (HI:RH)A-28B-103,106B-7,9
Headlamp leveling switchC-36B-131,133B-19,25
High mounted stop lampF-05B-144,145B-38,39
Horn (HI)A-23B-146B-7,8
Horn (LO)A-25B-146B-7,9
Horn relayA-05XB-73,146B-6,8
Horn switch C-206B-146B-22,28
IIdle speed control servoB-115B-88,96B-12,16
Ignition coil 1B-114B-82,83B-12,16
Ignition coil 2B-119B-82,83B-12,16
Ignition coil relay or no
connection B-09XB-73,83B-10,14
Ignition switchC-201B-76B-22,28
Injector 1B-27B-89,97B-11,15
Injector 2B-26B-89,97B-11,15
Injector 3B-25B-89,97B-11,15
Injector 4B-24B-89,97B-11,15
Instrument panel wiring harness and
A/C wiring harness combinationC-107B-175,181B-20,26
Instrument panel wiring harness and
console wiring harness combinationD-15B-195B-31,32
Instrument panel wiring harness and
control wiring harness combinationC-128B-153,181,184,198,200,202,203,205,
206,208,209,211,213,214,216,217,
218,229,230,233,234,235,236,239,
242,243B-21,26
Instrument panel wiring harness and
control wiring harness combinationC-129B-79,80,83,87,89,93,95,97,101,142,
143,149,186,190,212,228,253B-21,26
Instrument panel wiring harness and
control wiring harness combinationC-130B-84,87,92,95,100,142,143,148,150,
152,154,157,175,178,198,200,201,
204,205,206,212,213,216,219,228,
229,232,235,237,252,254,255,256,
257B-21,27

INDEX - In order of parts nameC-18
Wiring diagram
page Circuit diagram page Connector
No. Parts name
KKey reminder switchC-202B-253,255B-22,28
LLicence plate lamp (LH)F-13B-110,114B-38,39
Licence plate lamp (RH)F-12B-110,114B-38,39
Luggage compartment lampF-04B-119,123B-38,39
NNo connectionA-08XB-73B-6,8
No connectionA-34-B-9
No connectionB-07XB-73B-10,14
No connectionB-08XB-73B-10,14
No connectionB-10XB-73B-10,14
No connectionC-220B-54,55B-23,29
No connectionB-06XB-73B-10,14
No connectionC-225B-54,55,78B-23,29
No connection C-34-B-25
OOil pressure switchB-20B-157B-11,15
Outside/Inside air selection damper
control motor and potentiometerC-10B-175,181B-18,24
Oxygen sensorB-34B-88,96B-11,15
Oxygen sensor (Rear)D-22B-88,96B-31,33
PParking brake switchD-23B-157,201,209,213,221,232,242B-31,33
Power steering oil pressure switchA-48B-90,98B-7,9
Power window main switchE-07B-162,163,168,169B-34,36
Power window motor (Front:LH)E-05B-162,165B-34,36
Power window motor (Front:RH)E-20B-159,168B-35,37
Power window motor (Rear:LH)E-10B-161,167B-34,36
Power window motor (Rear:RH)E-25B-160,166B-35,37
Power window relayC-224B-54,55,158,159,165B-23,29
Power window sub switch (Passenger’s
side)E-19B-159,165B-35,37
Power window sub switch (Rear:LH)E-11B-161,167B-34,36
Power window sub switch (Rear:RH)E-24B-160,166B-35,37
Pressure sensor F-29B-216,224,234,244B-38,39
Proportioning valve (for ACD control)F-27B-216,224,235,245B-38,39
Proportioning valve (for AYC control)F-28B-235,245B-38,39

GENERAL -How to Use This Manual00-4
EXPLANATION OF MANUAL CONTENTS
Indicates procedures to be performed
before the work in that section is started,
and procedures to be performed after
the work in that section is finished.
Indicates (by symbols) where lubrica-
tion is necessary.
Maintenance and Servicing Procedures
The numbers provided within the diagram indi-
cate the sequence for maintenance and servic-
ing procedures.
DRemoval steps:
The part designation number corresponds
to the number in the illustration to indicate
removal steps.
DDisassembly steps:
The part designation number corresponds
to the number in the illustration to indicate
disassembly steps.DInstallation steps:
Specified in case installation is impossible
in reverse order of removal steps. Omitted
if installation is possible in reverse order of
removal steps.
DReassembly steps:
Specified in case reassembly is impossible
in reverse order of disassembly steps.
Omitted if reassembly is possible in reverse
order of disassembly steps.
Classifications of Major Maintenance/Service Points
When there are major points relative to maintenance and servicing procedures
(such as essential maintenance and service points, maintenance and service stan-
dard values, information regarding the use of special tools, etc.), these are ar-
ranged together as major maintenance and service points and explained in detail.
AA": Indicates that there are essential points for removal or disassembly.
"AA: Indicates that there are essential points for installation or reassembly.
Symbols for Lubrication, Sealants and Adhesives
Information concerning the locations for lubrica-
tion and for application of sealants and adhe-
sives is provided, by using symbols, in the dia-
gram of component parts or on the page follow-
ing the component parts page, and explained.: Grease
(multipurpose grease unless there is
a brand or type specified)
: Sealant or adhesive
: Brake fluid or automatic transmission fluid
: Engine oil, gear oil or air conditioner
compressor oil
: Adhesive tape or butyl rubber tape
Component Diagram
A diagram of the component parts is
provided near the front of each section
in order to give a reader a better under-
standing of the installed condition of
component parts.

GENERAL -Precautions Before ServiceGENERAL -Precautions Before Service00-19
SERVICING THE ELECTRICAL SYSTEM
Before replacing a component related to the electrical system
and before undertaking any repair procedures involving the
electrical system, be sure to first disconnect the negative
( - ) cable from the battery in order to avoid damage caused
by short-circuiting.
Caution
Before connecting or disconnecting the negative ( - ) cable,
be sure to turn off the ignition switch and the lighting
switch.
(If this is not done, there is the possibility of
semiconductor parts being damaged.)
APPLICATION OF ANTI-CORROSION AGENTS
AND UNDERCOATS
If oil or grease gets onto the oxygen sensor, it will cause
a drop in the performance of the sensor.
Cover the oxygen sensor with a protective cover when applying
anti-corrosion agents and undercoats.
PRE-INSPECTION CONDITION
“Pre-inspection condition” refers to the condition that the
vehicle must be in before proper engine inspection can be
carried out. If you see the words “Set the vehicle to the
pre-inspection condition”. in this manual, it means to set the
vehicle to the following condition.
DEngine coolant temperature: 80 to 90_C
DLamps, electric cooling fan and all accessories: OFF
DM/T: Neutral
DA/T: P range
VEHICLE WASHING
If high-pressure car-washing equipment or steam car-washing
equipment is used to wash the vehicle, be sure to note the
following information in order to avoid damage to plastic
components, etc.
DSpray nozzle distance: Approx. 40 cm or more
DSpray pressure: 3,900 kPa or less
DSpray temperature: 82_C or less
DTime of concentrated spray to one point: within 30 sec.
Approx.
40 cm

GENERAL -Precautions Before ServiceGENERAL -Precautions Before Service00-20
MUT-II
Refer to the “MUT-IIREFERENCE MANUAL” or “MUT-II
OPERATING INSTRUCTIONS” for instructions on handling
the MUT-II.
Connect the MUT-IIto the diagnosis connector as shown
in the illustration.
Caution
Turn the ignition switch to the LOCK (OFF) position before
connecting or disconnecting the MUT-II.
IN ORDER TO PREVENT VEHICLES FROM FIRE
“Improper installation of electrical or fuel related parts could cause a fire. In order to retain the high
quality and safety of the vehicle, it is important that any accessories that may be fitted or modifications/repairs
that may be carried out which involve the electrical or fuel systems, MUST be carried out in accordance
with MMC’s information/Instructions”.
ENGINE OILS
Health Warning
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin,
leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful
contaminants which may cause skin cancer. Adequate means of skin protection and washing facilities
must be provided.
Recommended Precautions
The most effective precaution is to adapt working practices which prevent, as far as practicable, the
risk of skin contact with mineral oils, for example by using enclosed systems for handling used engine
oil and by degreasing components, where practicable, before handling them.
Other precautions:
DAvoid prolonged and repeated contact with oils, particularly used engine oils.
DWear protective clothing, including impervious gloves where practicable.
DAvoid contaminating clothes, particularly underpants, with oil.
DDo not put oily rags in pockets, the use of overalls without pockets will avoid this.
DDo not wear heavily soiled clothing and oil-impregnated foot-wear. Overalls must be cleaned regularly
and kept separately from personal clothing.
DWhere there is a risk of eye contact, eye protection should be worn, for example, chemical goggles
or face shields; in addition an eye wash facility should be provided.
DObtain First Aid treatment immediately for open cuts and wounds.
DWash regularly with soap and water to ensure all oil is removed, especially before meals (skin cleansers
and nail brushes will help). After cleaning, the application of preparations containing lanolin to replace
the natural skin oils is advised.
DDo not use petrol, kerosine, diesel fuel, gas oil, thinners or solvents for cleaning skin.
DUse barrier creams, applying them before each work period, to help the removal of oil from the skin
after work.
DIf skin disorders develop, obtain medical advice without delay.
MUT-II
sub-assembly
ROM pack
MUT-˜