2007 MITSUBISHI LANCER EVOLUTION coolant temperature

INDEX - In order of parts nameC-13
Wiring diagram
page Circuit diagram page Connector
No. Parts name
DDoor switch (Rear:LH)D-08B-120,121B-30,32
Door switch (Rear:RH)D-06B-120,121B-30,32
Dual pressure switchA-36B-178,184B-7,9
EEGR solenoid valveB-112B-91,99B-12,16
Electric pump F-23B-216,224,234,244B-38,39
Electric pump relay B-139B-216,224,234,244B-13,17
Engine control relayB-11XB-73,86,94,252,254B-10,14
Engine coolant temperature gauge unitB-110B-148,152B-12,16
Engine coolant temperature sensorB-118B-89,97B-12,16
Engine speed detection connectorB-05XB-73,82,83,90,98B-10,14
Engine-ECUC-115B-87,88,89,90,91,92,93,95,96,97,98,
99,100,101,215,223,231,241,257B-20,26
Engine-ECUC-118B-82,83,88,90,91,92,93,96,98,99,100,
101,149,153,252,254,256B-20,26
Engine-ECUC-122B-84,86,87,90,91,93,94,95,98,99,101,
177,178,183,184,252,254,256,257B-20,26
Engine-ECUC-126B-82,83,86,88,89,90,91,93,94,96,97,
98,99, 101,102,178,184B-20,26
ETACS-ECUC-226B-54,55,105,108,112,113,116,117,118,
119,120,121,122,123,125,126,128,
129,134,136,137,138,140,141,158,
164,165, 170,171,172,173,188,189B-23,29
ETACS-ECUC-227B-125,128,170,172B-23,29
ETACS-ECUC-228B-105,108,112,113,116,117,118,119,
122,123,125,126,128,129,136,137,
140,141,158,159,164,165,170,171,
172,173, 188,189,258B-23,29
FFan controllerA-21B-102,176,182B-7,8
Floor wiring harness (LH) and 4WD
wiring harness combination F-24B-216,224,234,235,244,245B-38,39
Floor wiring harness (LH) and bumper
wiring harness combinationF-14B-110,114B-38,39
Floor wiring harness (LH) and J/B
combination C-216B-54,55,105,110,112,119,120,134,
158,171,185B-23
Floor wiring harness (LH) and rear door
wiring harness (LH) combinationD-12B-161,167,171,173B-30,32
Floor wiring harness (RH) and fuel
wiring harness combinationD-29B-93,101B-31,33
Floor wiring harness (RH) and fuel
wiring harness combinationD-30B-93,101,148,152,156,203,211,217,
225,233,243B-31,33

GENERAL -Precautions Before ServiceGENERAL -Precautions Before Service00-19
SERVICING THE ELECTRICAL SYSTEM
Before replacing a component related to the electrical system
and before undertaking any repair procedures involving the
electrical system, be sure to first disconnect the negative
( - ) cable from the battery in order to avoid damage caused
by short-circuiting.
Caution
Before connecting or disconnecting the negative ( - ) cable,
be sure to turn off the ignition switch and the lighting
switch.
(If this is not done, there is the possibility of
semiconductor parts being damaged.)
APPLICATION OF ANTI-CORROSION AGENTS
AND UNDERCOATS
If oil or grease gets onto the oxygen sensor, it will cause
a drop in the performance of the sensor.
Cover the oxygen sensor with a protective cover when applying
anti-corrosion agents and undercoats.
PRE-INSPECTION CONDITION
“Pre-inspection condition” refers to the condition that the
vehicle must be in before proper engine inspection can be
carried out. If you see the words “Set the vehicle to the
pre-inspection condition”. in this manual, it means to set the
vehicle to the following condition.
DEngine coolant temperature: 80 to 90_C
DLamps, electric cooling fan and all accessories: OFF
DM/T: Neutral
DA/T: P range
VEHICLE WASHING
If high-pressure car-washing equipment or steam car-washing
equipment is used to wash the vehicle, be sure to note the
following information in order to avoid damage to plastic
components, etc.
DSpray nozzle distance: Approx. 40 cm or more
DSpray pressure: 3,900 kPa or less
DSpray temperature: 82_C or less
DTime of concentrated spray to one point: within 30 sec.
Approx.
40 cm

ENGINE -Cylinder Head Gasket11A-29
5.0±1.0 N·m
61
2
3 4
57
8
910
11 12
1314
13±1 N·m
15
16
17
5.0±1.0 N·m
1819
9.0±1.0 N·m
9.0±1.0 N·m
(Engine oil)
1
Removal steps
1. Ignition coil connector
2. Crank angle sensor connector
3. Oxygen sensor connector
4. Fuel pressure solenoid valve
connector
5. Detonation sensor connector
6. Purge control solenoid valve
connector
7. Throttle position sensor connector
8. Idle speed control servo connector
9. Injector connector
10. Camshaft position sensor connector
11. Engine coolant temperature gauge
unit connector12. Engine coolant temperature sensor
connector
DRocker cover (Refer to P.11A-17.)
13. EGR solenoid valve connector
14. Secondary air control solenoid valve
connector
15. Vacuum tank, solenoid valve, vacuum
pipe and hose assembly
16. Brake booster vacuum hose
connection
17. Oil level gauge and guide assembly
18. O-ring
19. Purge hose connection

ENGINE -Engine Assembly11A-44
1
2
3 4
5
67
8
910
11 12
13
14
26±5 N·m
14±3 N·m
1516
18
5.0±1.0 N·m
1
5.0±1.0 N·m
11±1 N·m
17
Removal steps
1. Ignition coil connector
2. Crank angle sensor connector
3. Oxygen sensor connector
4. Fuel pressure solenoid valve
connector
5. Detonation sensor connector
6. Purge control solenoid valve
connector
7. Throttle position sensor connector
8. Idle speed control servo connector
9. Injector connector
10. Camshaft position sensor connector11. Engine coolant temperature gauge
unit connector
12. Engine coolant temperature sensor
connector
13. Alternator connector
14. EGR solenoid valve connector
15. Secondary air control solenoid valve
connector
16. Engine oil pressure switch
connector
17. Waste gate actuator mounting bolt
AA"18. Drive belt

ENGINE OVERHAUL -Specifications11B-6
Items Tightening torque N·m
Camshaft sprocket bolt88±10
Fuel system
Throttle body bolt19±3
EGR valve bolt20±2
Fuel pressure regulator bolt8.8±2.0
Delivery pipe and injector bolt11±1
Vacuum hose and pipe bolt11±1
Solenoid assembly bolt9±1
Vacuum tank bracket bolt9±1
Secondary air system, intake manifold
Exhaust manifold heat protector bolt14±1
Vacuum hose and pipe bolt11±1
Air pipe assembly bolt (eye bolt)49±5
Air pipe assembly bolt (M6 flange)11±1
Air pipe assembly bolt (M8 flange)24±3
Air pipe assembly bolt (M8 washer)14±1
Air control valve assembly bolt22±4
Air control valve bracket bolt22±4
MDP sensor bolt5±1
Intake manifold stay bolt31±3
Intake manifold bolt (M8)20±2
Intake manifold bolt nut (M8)36±6
Exhaust manifold
Engine hanger bolt19±3
Turbocharger heat protector bolt14±1
O2sensor44±5
Exhaust fitting bracket bolt47±6
Exhaust fitting bolt nut59±5
Air outlet fitting bolt19±1
Oil return pipe bolt (flange)14±1
Oil return pipe bolt (washer)9±1
Turbocharger assembly and pipe bolt, nut59±5
Oil pipe bolt (M10 eye bolt)17±2
Oil pipe bolt (M12 eye bolt)31±2
Oil pipe bolt (M12 flange)11±1
Water pipe bolt (flange)10±1
Water pipe bolt (eye bolt)42±7
Exhaust manifold nut (M8)33±6
Exhaust manifold nut (M10)55±10
Water pump, water hose
Engine coolant temperature sensor29±10
Engine coolant temperature gauge unit10.8±1.0

ENGINE OVERHAUL -Specifications11B-8
SEALANTS
ItemSpecified sealantQuantity
Engine support bracket bolt3MTMAAD Part No. 8672 or equivalentAs required
Semi-circular packing3MTMAAD Part No. 8672 or equivalentAs required
Rocker cover3MTMAAD Part No. 8672 or equivalentAs required
Water outlet fittingMitsubishi Genuine Part No. MD970389 or
equivalentAs required
Engine coolant temperature gauge unit3MTMAAD Part No. 8672 or equivalentAs required
Engine coolant temperature sensor3MTMAAD Part No. 8672 or equivalentAs required
Cylinder head (camshaft bearing cap mounting
section)3MTMAAD Part No. 8672 or equivalentAs required
Cam position sensor supportMitsubishi Genuine Part No. MD970389 or
equivalentAs required
Oil pressure switch3MTMAAD Part No. 8672 or equivalentAs required
Oil panMitsubishi Genuine Part No. MD970389 or
equivalentAs required
Oil seal caseMitsubishi Genuine Part No. MD970389 or
equivalentAs required
FORM-IN-PLACE-GASKET
FIPG is used for several members of this engine. With this gasket, caution is required to the application
amount, application procedure and state of the application surface so that the performance is sufficiently
attained.
If sufficient gasket is not applied, leaks could occur, and if too much is applied, the gasket could protrude
and plug or restrict the oil and water flow passage. Thus, to prevent leaks from the joined sections,
it is absolutely necessary to evenly apply the correct amount.
The FIPG used for the engine parts reacts with moisture in the air and hardens so use it for the normal
metal flange parts.
DISASSEMBLY
The parts assembled with FIPG can be easily disassembled without special means. However, in some
cases, the sealant on the seams must be broken by lightly tapping with a wood hammer or similar tool.
A smooth and thin gasket scraper can be lightly tapped into the seams but in this case, take care not
to damage the seams.
The special tool oil pan remover (MD998727) is set for this purpose.
WASHING THE GASKET SURFACE
Completely remove all matters adhered on the gasket surfaces with a gasket scraper or wire brush.
Confirm that the FIPG application surface is smooth. There must be no grease or foreign matter on
the gasket surface.
Always remove the old FIPG that has entered the mounting holes and screw holes.
APPLICATION PROCEDURES
Apply an even coat of FIPG within the predetermined radius. Completely cover the areas around the
mounting holes. The FIPG can be wiped off if it has not hardened. Install at the set position while the
FIPG is still wet (within 15 minutes). When installing, maker sure that the FIPG does not get on areas
other than the required areas. After installing, do not subject the application areas to oil or water or
start the engine until the FIPG has sufficiently hardened (approx. one hour). The FIPG application procedures
differ according to the member, so follow the procedures given in this manual and apply the FIPG.

ENGINE OVERHAUL -Water Pump and Water Hose11B-32
WATER PUMP AND WATER HOSE
REMOVAL AND INSTALLATION
1
2
3
45
67
8
9
10 11
12
13
10±1N•m
14±1N•m 23±2N•m10±1N•m
13±2N•m10.8±1.0 N•m
29±10 N•m
1415 16
23±4N•m
23±4N•m
Removal steps
1. Water hose
2. Water hose
3. Water hose
4. Water hose
"DA5. Engine coolant temperature sensor
"CA6. Engine coolant temperature gauge
unit
"BA7. Water outlet fitting
8. Thermostat9. Thermostat housing
10. Gasket
"AA11. O-ring
"AA12. Water inlet pipe
"AA13. O-ring
14. Water pump
15. Water pump gasket
16. Knock sensor

ENGINE OVERHAUL -Water Pump and Water Hose11B-33
INSTALLATION SERVICE POINTS
"AAO-RING/WATER INLET PIPE INSTALLATION
Replace the O-ring for the water inlet pipe with a new part,
and apply water on the periphery of the O-ring so that it
can be inserted easily into the water pump and thermostat
housing.
Caution
(1) Never apply grease or oil, such as engine oil, on the
O-ring.
(2) Install the water inlet pipe onto the thermostat
housing, and then fix.
"BAWATER OUTLET FITTING INSTALLATION
Squeeze out form-in-place gasket at a 3 mm width, and apply
at the position shown in the illustration.
Form-in-place gasket
Specified gasket:
Mitsubishi Genuine Part No. MD970389 or
equivalent
"CAENGINE COOLANT TEMPERATURE GAUGE UNIT
INSTALLATION
When reusing the bolts, apply the specified sealant on the
threads.
Sealant
Specified sealant:
3M
TMAAD Part No. 8672 or equivalent
"DAENGINE COOLANT TEMPERATURE SENSOR
INSTALLATION
Apply the specified sealant onto the threads.
Sealant
Specified sealant:
3M
TMAAD Part No. 8731 or equivalent
Caution
Make sure that the tool does not contact the connector
section (resin section).