2007 MITSUBISHI LANCER EVOLUTION automatic transmission

STEERING - Power Steering Gear Box and Linkage37A-21
Lubrication and Sealing Points
Fluid:
Automatic transmission
fluid DEXRON II
Fluid:
Automatic transmission
fluid DEXRON II
Fluid:
Automatic transmission
fluid DEXRON II
Fluid:
Automatic transmission
fluid DEXRON II
Grease: Repair kit grease
Sealant: 3M ATD part No. 8661,
8663 or equivalent
Fluid:
Automatic transmission
fluid DEXRON II
Grease: Repair kit grease
Fluid:
Automatic transmission
fluid DEXRON II
Grease: Silicone grease

STEERING - Power Steering Gear Box and Linkage37A-24
REASSEMBLY SERVICE POINTS
"AAOIL SEAL INSTALLATION
"BANEEDLE BEARING/LOWER BEARING
INSTALLATION
"CARACK ASSEMBLY INSTALLATION
1. Apply repair kit grease to the teeth of the rack assembly.
Caution
Use care not to close the vent hole in the rack with
grease.
2. Cover the serrations of the rack assembly with the special
tool.
3. Apply specified fluid to the outer surfaces of the special
tool, seal ring and O-ring.
Specified fluid:
Automatic transmission fluid DEXRONII
Caution
Do not use ATF-SPIIM and ATF-SPIII.
4. Slowly insert the rack covered with the special tool from
the power cylinder side of the gear housing.
Caution
Carefully push in the rack with the oil seal centre
and the special tool end matched. This is to avoid
the retainer spring coming off.MB991197
Gear housing
Oil seal MB991199
Needle
bearingMB990925
(MB990938)
MB991202
Lower
bearing MB990925
(MB990938)
MB991202
Vent hole
Seal ring, O-ring
MB991214 Oil seal

STEERING - Power Steering Gear Box and Linkage37A-25
"DAOIL SEAL/RACK BUSHING INSTALLATION
1. Apply specified fluid to the outer surface of the oil seal.
Using the special tool, press in the oil seal until it is flush
with the bushing end face.
Specified fluid:
Automatic transmission fluid DEXRONII
Caution
Do not use ATF-SPIIM and ATF-SPIII.
2. Apply the specified fluid to the oil seal inner surface and
the O-ring.
Specified fluid:
Automatic transmission fluid DEXRONII
Caution
Do not use ATF-SPIIM and ATF-SPIII.
3. Wrap the rack end with plastic tape, and push the rack
bushing onto the rack.
"EACIRCLIP INSTALLATION
Align the mark on the rack stopper and the slot in the cylinder.
Then, insert the circlip into the rack stopper hole through
the cylinder hole. Turn the rack stopper clockwise and insert
the circlip firmly.
"FAUPPER OIL SEAL/UPPER BEARING
INSTALLATION
"GASEAL RING INSTALLATION
After installation, using the special tool or by hand, compress
seal rings that expand during installation.
MB990925
(MB990927)
Oil seal
O-ring
Rack
bushing
Rack bushingPlastic tape Rack
Slot
Circlip
SlotCirclip
MB991203MB991203 MB990925
(MB990938)
Upper oil
seal
MB990925
(MB990938)
Bearing
MB991317

STEERING - Power Steering Oil Pump/Power Steering Oil Hoses37A-30
"BAPRESSURE HOSE ASSEMBLY/SUCTION HOSE
REMOVAL
Install the pressure hose assembly and suction hose as
illustrated.
DISASSEMBLY AND REASSEMBLY
21±3 N·m
3
4
2 1
39±5 N·m
: Automatic transmission fluid DEXRONII
NOTE
Disassembly steps
1. Suction connector
2. O-ring3. Connector
4. Gasket
POWER STEERING OIL HOSES
REMOVAL AND INSTALLATION
Caution
1. Before removing the clock spring, always see GROUP 52B - Caution for Service and Air Bag
Module Clock Spring
2. If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to
contact the parts or tools to the caliper, because the paint of caliper will be scratched.
3. On the tightening section indicated in the mark (*), lightly tighten the nut first, and then finally
tighten it with the engine weight applied on the body.
Suction hose
Pressure hose
assembly
Marking
Notch