334 Controls in detailMirrorsAuto-dimming rear view mirrors
The reflection brightness of the exterior
rear view mirror on the driver’s side and
the interior rear view mirror will respond
automatically to glare when
the ignition is switched on
(page 315)
and
incoming light from headlamps falls on
the sensor in the interior rear view
mirrorThe interior rear view mirror will not react if
reverse gear R is engaged
the interior lighting is turned on
!
If an exterior rear view mirror housing is
forcibly pushed forward (hit from the rear), repo-
sition it manually by applying firm pressure until
it snaps back into place.
If an exterior rear view mirror housing is forcibly
pushed rearward (hit from the front), press
button1 to fold mirrors in, then press
button1 again to fold mirrors out. Do not force
mirrors by hand as this may damage the adjust-
ment mechanism.
The mirror housing is then properly positioned
and you can adjust the mirror in the usual man-
ner.
Warning!
G
The auto-dimming function does not react if
incoming light is not aimed directly at sen-
sors in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver’s side do not
react, for example, if the rear window sun-
shade is in raised position.
Light hitting the mirror(s) at certain angles
(incident light) could blind you. As a result,
you may not be able to observe traffic con-
ditions and could cause an accident.Warning!
G
In case of an accident, liquid electrolyte may
leak from the mirror housing if the mirror
glass breaks.
Electrolyte has an irritating effect. Do not al-
low the liquid to come into contact with
eyes, skin, clothing, or respiratory system.
In case it does, immediately flush affected
area with water, and seek medical help if
necessary.!
Electrolyte drops coming into contact with
the vehicle paint finish can be completely re-
moved only while in the liquid state by applying
plenty of water.
Warning!
G
Exercise care when using the passen-
ger-side exterior rear view mirror. The mirror
surface is convex (outwardly curved surface
for a wider field of view). Objects in mirror
are closer than they appear. Check your in-
side rear view mirror or glance over your
shoulder before changing lanes.
351 Controls in detail
Windshield wipers
Windshield wipers
Combination switch1Switching on windshield wipers
2Single wipe
Wiping with windshield washer fluid
Switch on the ignition (
page 315).
Switching on/off windshield wipers
Turn the combination switch to the de-
sired position depending on the inten-
sity of the rain.
MWindshield wipers off
USlow intermittent wiping
(rain sensor operation low sen-
sitivity)
VFast intermittent wiping
(rain sensor operation low sen-
sitivity)
uSlow continuous wiping
tFast continuous wiping
!
If the windshield wipers leave smears on the
windshield after the car has been driven through
an automatic car wash, then wax or other resi-
due is on the windshield. Shortly after washing
the car in an automatic car wash, clean the wind-
shield with windshield washer fluid
(
page 352).
!
Do not operate the wipers when the wind-
shield is dry. Dust that accumulates on a wind-
shield might scratch the glass and/or damage
the wiper blades when wiping occurs on a dry
windshield. If it is necessary to operate the wip-
ers in dry weather conditions, always operate
the wipers with windshield washer fluid
(
page 352).
!
If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediate-
ly.
For safety reasons, stop the vehicle in a safe
location,
turn off the engine by turning the
SmartKey to position0 and withdraw
SmartKey from starter switch
or
turn off the engine by pressing the
KEYLESS-GO* start/stop button
(page 317) and open the driver’s door
(with the driver’s door open, starter
switch is in position0, same as with
SmartKey removed from starter switch)
before attempting to remove any blockage.
Remove blockage.
Turn the windshield wipers on again.If the windshield wipers fail to function at all in
combination switch position u,
set the combination switch to the next high-
er wiper speed
have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center
352 Controls in detailWindshield wipersIntermittent wiping
Only switch on intermittent wiping under
wet weather conditions or in the presence
of precipitation.
Set the wiper switch to position U
or V.The wipers move across the wind-
shield. Afterward, the wiping intervals
are determined by the wetness of the
windshield.
After the initial wipe, pauses between
wipes are automatically controlled by the
rain sensor.
Single wipe
Press the combination switch briefly in
the direction of arrow2.
The windshield wipers wipe one time
without washer fluid.
Wiping with windshield washer fluid
Press the combination switch in the di-
rection of arrow2 past the resistance
point.
The windshield wiper operates with
washer fluid.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system”
(
page 498).
i
When the windshield wipers are switched on
and you brake the vehicle to a stop, the wipers
operate more slowly.
!
Do not leave windshield wipers in intermit-
tent setting when the vehicle is taken to an auto-
matic car wash or during windshield cleaning.
Wipers will operate in the presence of water
sprayed on the windshield, and windshield wip-
ers may be damaged as a result.
!
If you have set intermittent wiping, dirt on
the surface of the rain sensor or optical effects
may cause the windshield wipers to wipe in an
undesired fashion. This could then damage the
windshield wiper blades or scratch the windows.
You should therefore switch off the windshield
wipers when weather conditions are dry.
i
Intermittent wiping is interrupted when the
vehicle is at a standstill and a front door is
opened. This protects persons getting into or out
of the vehicle from being sprayed.
Intermittent wiping will be continued when
all doors are closed and the automatic trans-
mission is set to positionD orR
or
the wiper setting is changed using the com-
bination switch
i
To prevent smears on the windshield, wipe
with windshield washer fluid every now and then
even when it is raining.
353 Controls in detail
Power windows
Power windows
Opening and closing power windows
The door windows are opened and closed
electrically. The switches
for all side windows are on the driver’s
door
for the front passenger side window
are on the front passenger door
for each rear side window are on the
rear doors
1Left front door window
2Right front door window
3Left rear door window
4Right rear door window
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
Activate the override switch (
page 67)
when children are riding in the back seats of
the vehicle. The children may otherwise in-
jure themselves, e.g. by becoming trapped
in the window opening.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if the switch was pressed past the resis-
tance point and released, by pressing the
lower part of the respective switch again.
The door windows are equipped with the ex-
press-close and automatic reversal func-
tion. If the window encounters an
obstruction that blocks its path in a circum-
stance where you pressed the switch past
the resistance point and released it to close
the window, the automatic reversal function
will stop the window and open it slightly.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pressing and
holding the switch, by pressing and holding
button ‹ on the SmartKey or SmartKey
with KEYLESS-GO*, by pressing and holding
the sensor surface (vehicles with
KEYLESS-GO*) on an outside door handle,
or by pressing and holding button, on
the climate control panel, the automatic re-
versal function will not operate.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment may cause an accident
and/or serious personal injury.
355 Controls in detail
Power windows
Stopping during Express-operation:
Briefly press the respective power win-
dow switch again.
Rear side window sunshades*
Closing: With the side window fully
closed, press top part of respective
rocker switch3 or4 (
page 353).
The rear side window sunshade will be
fully closed.
Opening: Press bottom part of respec-
tive rocker switch3 or4
(page 353).
The rear side window sunshade will be
fully opened.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously:
opening the side windows and rear side
window sunshades*
opening the tilt/sliding sunroof or
tilt/sliding panel* and extending the
roller sunblinds*
turning on the seat ventilation* for the
driver’s seat
Aim transmitter eye of the SmartKey or
SmartKey with KEYLESS-GO* at the
driver’s outside door handle. The
SmartKey or SmartKey with
KEYLESS-GO* must be in close proxim-
ity to the driver’s door handle.
!
If the upward movement of the window is
blocked during the closing procedure, the win-
dow will stop and open slightly. Remove the ob-
struction, press the respective power window
switch at the upper part again past the resis-
tance point and release. If the window still does
not close when there is no obstruction, press
and hold the respective power window switch at
the upper part. The side window will then close
without the obstruction sensor function.
i
The rear side window sunshade cannot be
partially closed.
i
The rocker switches on the rear doors can
also be used to close the rear side window sun-
shades on the other side of the vehicle.
i
The rocker switches on the driver’s door
take precedence over the rocker switches on the
other doors.
i
The “Summer opening” function can only be
activated via the remote control.
i
The seat ventilation* for the driver’s seat is
automatically set to the highest level if activated
via summer opening feature.
356 Controls in detailPower windowsVehicles with tilt/sliding sunroof
Press and hold button Œ until the
side windows and tilt/sliding sunroof
have reached the desired position.
Release button Œ to interrupt pro-
cedure.
Vehicles with panorama roof* and/or
rear side window sunshades*
If roller sunblinds are retracted and/or
rear side window sunshades* are closed:
Press and hold button
Œ
. The win-
dows and sunblinds and/or rear side
window sunshades* begin to open/ex-
tend after approximately 1 second.
With the windows and roller blinds
and/or rear side window sunshades*
fully opened/extended, press and hold
button
Œ
again. The tilt/sliding pan-
el tilts and opens.If roller sunblinds and/or rear side window
sunshades* are open/extended:
Press and hold button
Œ
. The win-
dows move down and the tilt/sliding
panel tilts and opens after approxi-
mately 1 second.
Release button
Œ
to interrupt proce-
dure.
Convenience closing feature
When you lock the vehicle, you can close
the side windows and tilt/sliding sunroof
or tilt/sliding panel* simultaneously.
Afterward, you can close the roller sun-
blinds* of the panorama tilt/sliding sun-
roof* and the rear side window
sunshades*.i
The function of the SmartKey overrules the
KEYLESS-GO function.
Warning!
G
When closing the windows and the tilt/slid-
ing sunroof or tilt/sliding panel*, make sure
that there is no danger of anyone being
harmed by the closing procedure.
If potential danger exists, proceed as fol-
lows:
Release button ‹ to stop the closing
procedure. To open, press and hold but-
ton Œ. To continue the closing after
making sure that there is no danger of
anyone being harmed by the closing pro-
cedure, press and hold button‹.
Vehicles with KEYLESS-GO*:
Release the sensor surface on the out-
side door handle (
page 358) to stop
the closing procedure.
Immediately pull on the same outside
door handle and hold firmly. The side
windows and the tilt/sliding sunroof or
tilt/sliding panel* will open for as long
as the outside door handle is held but
the door is not opened.
357 Controls in detail
Power windows
Vehicles with SmartKey
Aim transmitter eye of the SmartKey
towards the sensor in the driver’s door
handle. The SmartKey must be in close
proximity to the driver’s door handle.Vehicles with tilt/sliding sunroof
Press and hold button ‹ until the
side windows and the tilt/sliding sun-
roof are completely closed.
Release button ‹ to interrupt pro-
cedure.Vehicles with panorama roof* and/or
rear side window sunshades*
Press and hold button ‹ until the
side windows and the tilt/sliding panel
are completely closed.
Press and hold button ‹ again.
The roller sunblinds and/or rear side
window sunshades* close.
Release button ‹ to interrupt pro-
cedure.
i
If you press ‹ while one of the front side
windows is open and one of the rear side win-
dows is closed, for example, then the front side
window and the rear side window sunshade will
be closed. To prevent this from happening, first
open all side windows slightly by briefly
pressingŒ and then close all side windows
by pressing ‹.
358 Controls in detailPower windowsVehicles with KEYLESS-GO*
1Sensor surface on door handle
The SmartKey with KEYLESS-GO must be
located outside the vehicle within approxi-
mately 3 ft. (1 m) of a door.
Close all doors.Vehicles with tilt/sliding sunroof
Touch and hold sensor surface1 until
the windows and the tilt/sliding sun-
roof are completely closed.
Release sensor surface1 to interrupt
procedure.Vehicles with panorama roof* and/or
rear side window sunshades*
Touch and hold sensor surface1 until
the windows and the tilt/sliding panel
are completely closed.
Touch and hold sensor surface1
again.
The roller sunblinds and/or rear side
window sunshades* close.
Release sensor surface1 to interrupt
procedure.
i
Make sure that you are only touching the
sensor surface.
i
Make sure that you are only touching the
sensor surface.
i
If you touch the sensor surface while one of
the front side windows is open and one of the
rear side windows is closed, for example, the
front side window will be closed as well as the
rear side window sunshade*.