2007 Lancia Musa lock

274
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
FRONT SIDELIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒remove the snap-fitted bulb holder A, remove the bulb B and
replace it;
❒refit the snap-fitted bulb holder A;
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
FRONT FOG LIGHTS (where provided)
Contact Lancia Dealership to replace front fog light bulbs.
L0D0353m
L0D0354m

275
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
REAR LIGHT UNITS
To change the bulb, proceed as follows:
❒open the tailgate;
❒turn the fastener A counter-clockwise (for the left lid) or clockwise
(for the right lid) and remove the cover;
❒disconnect the electrical connector C;
❒slacken the two fastening nuts B;
❒to remove the headlight, pull it in perpendicular direction using
the handle on the headlight;
❒press the bulb holder tabs and remove it from its housing;
❒remove bulbs D - E - F - G lightly pushing them and turning them
counter-clockwise;
❒refit the bulb holder and make sure the two tabs are fastened and
then connect the electrical connector C; drive in the two fastening
nuts B; refit the cover checking that the tabs are fitted in their seat
and turning the fastener A counter-clockwise (for the left lid) or
clockwise (for the right lid) to hook it.
In the event of a failure (burnt-out bulbs) on taillights, brake lights
will switch on dimmed automatically in order to guarantee temporary
lighting at the back of the car.
After replacing the burnt-out bulb the taillights will operate regularly.
L0D0187m
L0D0188m

277
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
NUMBER PLATE LIGHT
To change the bulb, proceed as follows:
❒work in the point shown by the arrow and remove lens A;
❒replace the bulb B releasing the side contacts, making sure that the
new bulb is properly locked between contacts;
❒refit the lens.
IF AN INTERIOR LIGHT BURNS OUT
For the type of bulb and power rating, see “When needing to change
a bulb”.
FRONT CEILING LIGHT
To change the bulb, proceed as follows:
❒work in the points shown by the arrows and remove the light unit A;
❒open the protective cover B;
❒change the bulbs C releasing them from the side contacts and
making sure the new bulbs are correctly fastened between the
contacts;
❒close the cover B and fasten the light unit A in its housing making
sure it clicks into place.
L0D0357m
L0D0193m
L0D0194m

283
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
FUSE SUMMARY TABLE
Control box on dashboard
USERFUSE AMPERE
Right-hand dipped beam headlightF12 15
Left-hand dipped beam headlight / headlight aiming device F13 15
Reversing lights / engine compartment control box relay coils / body computer F31 7,5
+30 Driver’s / passenger’s door control units (*) F32 15
Left rear power windowF33 20
Right rear power windowF34 20
+15 Cruise control, signal from switch on brake pedal for control units (*) F35 7,5
+30 Presetting for trailer control unit, rear locks front locks with single door control unit (*) F36 20
+15 Third brake light, instrument panel, brake lights (*) F37 10
Boot unlockingF38 15
+30 EOBD diagnostic socket, sound system, navigator, tyre pressure control unit (*)F39 10
Rear heated screenF40 30
Heated door electric mirrorsF41 7,5
+15 ABS / ESP control unit (*)F42 7,5
Windscreen wiper/washerF43 30
Cigar lighter / current socket on tunnelF44 20
Heated seatsF45 15
Boot current socketF46 20
Driver’s door control unit power supply (power window, lock) F47 20
Passenger’s door control unit power supply (power window, lock) F48 20
+15 utilities (left and central dashboard control lights, electric mirrors, heated seat control
lighting, presetting for radiotelephone, navigator, rain / daylight sensors, parking sensor control unit,
sunroof control lighting) (*)F49 7,5
Airbag control unitF50 7,5
+15 Tyre pressure control unit, ECO / Sport control (*) F51 7,5
Rear screen wiper/washerF52 15
+30 Direction indicators, hazard lights, instrument panel (*) F5 10
(*) +30 = battery directive positive terminal (not under key)
+15 = positive terminal under key

289
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
WARNING
WARNING
Do not start the engine when towing the car.
WARNING
While the car is being towed with the
engine off, remember that the brake pedal
and steering will require more effort as
you no longer have the benefit of the brake
booster and the electrical power steering.
Do not use flexible cables to tow. Avoid
jerking. Whilst towing, ensure that the
coupling to the car does not damage the
surrounding components. When towing the
car, you must comply with the specific
traffic regulations regarding the tow hitch
and how to tow on the road. TOW RING HOOKING
Proceed as follows:
❒take the tow ring B from its support;
❒tighten the ring on the rear or front threaded pin.
Before starting to tow, turn the ignition
key to MAR and then to STOP. Do not
remove the key. If the key is removed, the
steering lock engages automatically which
prevents the wheels being turned.
L0D0204m
L0D0205m

292
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
SERVICE SCHEDULE
Thousands of km
Check tyre conditions/wear and
adjust pressure if required
Check light system operation
(headlights, direction indicators, hazard lights, boot lights,
passenger compartment lights, dashboard warning lights, etc.)
Check windscreen/washer
(nozzles/and blade position regulation)
Check front disk brake pad conditions and wear
Check rear drum brake lining conditions
and wear
Sight inspect the conditions of: body external parts, underbody
protection pipes and hoses (exhaust, fuel, brakes),
rubber parts (boots, sleeves, bushes, etc.)
Check for bonnet and boot lock cleanness, lever cleanness
and lubrication
Check tension and adjust accessory drive belts
(excluding engines with automatic belt tighteners)
Check tension and adjust accessory drive belts
Check and adjust tappet clearance
(1.48V(where provided)-1.9 Multijet versions)
20 40 60 80 100 120 140 160 180
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●
●●●●● ●●●●
●●●●● ●●●●
●
●● ● ●
●● ● ●

ANNUAL INSPECTION SCHEDULE
For cars with an annual mileage of below 20,000
km (for example about 15,000 km) the following
yearly inspection programme is provided:
❒check tyre conditions/wear and adjust pressure if
required (including the spare wheel);
❒check lighting system operation (headlights,
direction indicators, hazard lights, boot lights,
passenger compartment lights, warning lights,
etc.);
❒check windscreen/washer
(nozzles/and blade position regulation)
❒check front disk brake pad conditions and wear;
❒sight inspect the conditions of: engine, gearbox,
transmission, pipes and hoses (exhaust - fuel -
brakes), rubber parts (boots, sleeves, bushes, etc;
❒check for bonnet and boot lock cleanness, lever
cleanness and lubrication;
❒check battery charge;
❒visual check on various drive belt conditions;
❒top up fluid levels (engine coolant, brakes,
windscreen washer, battery, etc.);
❒change engine oil;
❒change engine oil filter;
❒replace pollen filter (where provided).
ADDITIONAL CHECKS
Every 1,000 km or before long journeys, check and
top up if required:
❒engine coolant fluid level;
❒brake fluid level;
❒windscreen washer fluid level;
❒tyre pressure and conditions.
Every 3,000 km check and top up if required:
engine oil level.
You are recommended to use FL Selenia products,
designed and produced specifically for Lancia cars
(see table “Capacities” in section “Technical
specifications”).
294
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE

Changing the windscreen wiper blades
Proceed as follows:
❒raise the windscreen wiper arm A and position the blade so that it
forms an angle of 90° with the arm;
❒press tab B of the coupling spring and remove the blade to be
replaced from the arm A;
❒fit the new blade by inserting the tab into the special slot in the
arm. Make sure it is properly locked into place.
Changing the rear window blade
Proceed as follows:
❒raise the cover A and remove the arm from the car, slackening the
nut B that fastens it to the pivot pin;
❒fit the new arm, positioning it correctly, and fully tighten the nut;
❒lower the cover.
312
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
L0D0217m
L0D0218m