2007 Lancia Musa lock

217
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
INCOMPLETE DOOR LOCKING
The warning light on the dial turns on (together with the message on
the display) when one or more doors, the boot or the bonnet are not
properly shut.
Symbols
¯/˙shown on the display indicate incomplete left/right door
closing.
´
(*) Or rear
red(*)
“DUALDRIVE” ELECTRIC POWER STEERING SYSTEM
The wording CITY is only displayed when the “dualdrive” electric
power steering is engaged.
Warning
light on
dial Message on
multifunction
display

239
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
EBD SYSTEM FAILURE - System unavailable
The turning on at the same time of the xand>warning lights on
the dial (together with the message on the display) with the engine
running indicates that the EBD system is inefficient or unavailable.
In this case heavy braking may cause the rear wheels to lock before
time, with the possibility of skidding.
Drive with the utmost care to the nearest Lancia Dealership to have
the system checked.
x
+
>
red
amber
Warning
light on
dial Message on
multifunction
display

252
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DOOR OPENING/CLOSING
Emergency door locking device from outside
The doors are fitted with a device which makes it possible to close the
doors with the lock without power supply.
To close, proceed as follows:
❒insert the ignition key in the pawl B
❒turn the device to position 1 and close the ledge.
To open, proceed as follows:
❒insert the key in the pawl and turn it clockwise
❒open the driver’s door
❒from the vehicle inside open the remaining doors by operating the
levers located in the handles.
L0D0247m

260
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Lancia Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure.
Disconnect the quick connection and connect it directly to the tyre
valve; in this way the cylinder is not connected to compressor and the
sealing fluid will not flow into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection A to the cylinder and fit the transparent tube B in-
to the proper space.
L0D0367m
L0D0368m

269
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IMPORTANT The headlight inner surface may be lightly misted over:
this is not a fault but a natural fact due to low temperature and the
level of air humidity. It will disappear as soon the headlights are
turned on. The presence of drops inside the headlights means water
infiltration, therefore contact Lancia Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your car:
AGlass bulbs: clipped into position. Pull to remove.
BBayonet type bulbs: press the bulb, turn counterclockwise to
remove this type of bulb from its holder.
CTubular bulbs: free them from their contacts to remove.
D-EHalogen bulbs: to remove the bulb, release the clip holding
the bulb in place.
L0D0178m

271
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IF AN EXTERIOR LIGHT BURNS OUT
For the type of bulb and power rating, see “When needing to change
a bulb”.
FRONT LIGHT UNITS
The front light units contain the side/taillights, dipped beam, main
beam and direction indicator bulbs.
To replace side/taillight, dipped beam and main beam bulbs:
disconnect the power connector, release retainer B and remove
cover A.
The bulbs are arranged inside the light unit as follows:
C: Direction indicators
D: Main beam headlights
E: Sidelights
F: Dipped beam headlights
Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
L0D0345m
L0D0346m

272
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒turn the bulb holder A counterclockwise and remove it;
❒release the two tabs B from the catches, remove bulb C and replace
it;
❒refit the bulb holder A into its seat and turn it clockwise.
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒release the bulb holder catch A;
❒disconnect the electric connector B;
❒remove the bulb C and replace it;
❒fit the new bulb, making the tabs of the metallic part coincide with
the grooves on the reflector, reconnect the electrical connector B
then hook the bulb holder catch A;
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
L0D0348m
L0D0350m

273
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒turn the bulb holder A counterclockwise and remove it;
❒remove the bulb B pushing it gently and turning counterclockwise
(“bayonet”);
❒replace the bulb;
❒refit the bulb holder turning it clockwise, checking that it is
secured correctly.
Side
To change the bulb, proceed as follows:
❒lever in the point shown by the arrow to compress the catch and to
remove unit A;
❒turn the bulb holder B counterclockwise, remove the snap-fitted
bulb and replace it;
❒refit the bulb holder B in the transparent cover, then position the
unit making sure the catch clicks into place.
L0D0351m
L0D0148m