2007 Lancia Musa clock

260
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Lancia Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure.
Disconnect the quick connection and connect it directly to the tyre
valve; in this way the cylinder is not connected to compressor and the
sealing fluid will not flow into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection A to the cylinder and fit the transparent tube B in-
to the proper space.
L0D0367m
L0D0368m

269
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IMPORTANT The headlight inner surface may be lightly misted over:
this is not a fault but a natural fact due to low temperature and the
level of air humidity. It will disappear as soon the headlights are
turned on. The presence of drops inside the headlights means water
infiltration, therefore contact Lancia Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your car:
AGlass bulbs: clipped into position. Pull to remove.
BBayonet type bulbs: press the bulb, turn counterclockwise to
remove this type of bulb from its holder.
CTubular bulbs: free them from their contacts to remove.
D-EHalogen bulbs: to remove the bulb, release the clip holding
the bulb in place.
L0D0178m

272
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒turn the bulb holder A counterclockwise and remove it;
❒release the two tabs B from the catches, remove bulb C and replace
it;
❒refit the bulb holder A into its seat and turn it clockwise.
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the relevant catch;
❒release the bulb holder catch A;
❒disconnect the electric connector B;
❒remove the bulb C and replace it;
❒fit the new bulb, making the tabs of the metallic part coincide with
the grooves on the reflector, reconnect the electrical connector B
then hook the bulb holder catch A;
❒Once replacement is over, refit the cover pressing it in the middle
until hearing the locking click. Then, check for proper locking into
place.
L0D0348m
L0D0350m

273
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒turn the bulb holder A counterclockwise and remove it;
❒remove the bulb B pushing it gently and turning counterclockwise
(“bayonet”);
❒replace the bulb;
❒refit the bulb holder turning it clockwise, checking that it is
secured correctly.
Side
To change the bulb, proceed as follows:
❒lever in the point shown by the arrow to compress the catch and to
remove unit A;
❒turn the bulb holder B counterclockwise, remove the snap-fitted
bulb and replace it;
❒refit the bulb holder B in the transparent cover, then position the
unit making sure the catch clicks into place.
L0D0351m
L0D0148m

275
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
REAR LIGHT UNITS
To change the bulb, proceed as follows:
❒open the tailgate;
❒turn the fastener A counter-clockwise (for the left lid) or clockwise
(for the right lid) and remove the cover;
❒disconnect the electrical connector C;
❒slacken the two fastening nuts B;
❒to remove the headlight, pull it in perpendicular direction using
the handle on the headlight;
❒press the bulb holder tabs and remove it from its housing;
❒remove bulbs D - E - F - G lightly pushing them and turning them
counter-clockwise;
❒refit the bulb holder and make sure the two tabs are fastened and
then connect the electrical connector C; drive in the two fastening
nuts B; refit the cover checking that the tabs are fitted in their seat
and turning the fastener A counter-clockwise (for the left lid) or
clockwise (for the right lid) to hook it.
In the event of a failure (burnt-out bulbs) on taillights, brake lights
will switch on dimmed automatically in order to guarantee temporary
lighting at the back of the car.
After replacing the burnt-out bulb the taillights will operate regularly.
L0D0187m
L0D0188m