2007 ISUZU KB P190 Electrical

8A-162 ELECTRICAL-BODY AND CHASSIS
5. Headlight does not go out

Checkpoint Trouble Cause Countermeasure


Replace the lighting relay
Lighting relay continuity
between connector 1
X6
- 2
X6 (Should be no
continuity)

Relay point fused

NG

Replay the combination
switch Lighting switch continuity
between connector 3
B60
-1
B60 when switch is
OFF(S hould be no continuity)

point fused or faulty


NG
OK
OK

Repair or replace the
combination switch
Dimmer ⋅passing switch con-
tinuity between connector
3
B60 - 1 B60 when switch
is not operating
(Should be no continuity)

Switch point fused or faulty

NG
Repair short circuit
between 3
X6 - 3 B60
and 5
X2 - 2 B60
Check if headlight goes out
when connector
C2 , C36
is disconnected


Short circuit

NG
OK



6. Insufficient headlight brightness



Replace the headlight bulb

Headlight bulb

Bulb filament faulty

NG

Repair the wiring
Dimmer ⋅passing switch
W ire continuity between con-
nector 1
B60 - C2


Poor ground point contact

NG
OK

Clean the light lens

Headlight lens

Lens dirty

NG
OK



BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-163
7. Passing light does not function when dimmer switch is operated

Checkpoint Trouble Cause Countermeasure


Repair or replace the dimmer
switch

Dimmer switch

Poor switch point contact

NG

Repair open circuit between
3
X6 - 3 B60

Voltage between
3
B60 - ground (Should
be battery v oltage present)


Open circuit

NG
OK



8. Headlight beam does not change when dimmer switch is operated

Repair or replace the dimmer
switchDimmer switchLoose beam lever or foreign
material in switch
NG




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-164 ELECTRICAL-BODY AND CHASSIS
TAIL LIGHT, LICENSE PLATE LIGHT, CLEARANCE LIGHT

1. All lights do not light

Checkpoint Trouble Cause Countermeasure



Repair or replace the
combination switch
Lighting switch continuity
between connector
2
B60 - 1 B60


Poor switch point or connector
contact

NG

Reinstall or replace the tail
relay

Tail relay


Poor relay contact or relay
faulty

NG
OK

Reinstall or replace the fuse
No. EB12 (LH), EB11 (RH)
Fuse No. EB12 (LH) or EB11
(RH) (10A, Relay and fuse
box)
Poor fuse contact or blown

NG
OK



2. Tail light does not light


Replace the bulb or repair
connector contact

Tail light bulb continuity

Bulb burned out or poor
connector contact

NG

Repair open circuit or
connector contact
Continuity between connector
3
F5 - 4 F5 (RH)
or 3
F6 - 4 F6 (LH)


Open circuit or poor connector
contact

NG
OK



BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-165
3. License plate light does not light

Checkpoint Trouble Cause Countermeasure



Repair open circuit or
connector contact

Continuity between
connector 1
T4 - 2 T4 or 1

T3 - 2 T3

Open circuit or poor connector
contact

NG

Replace the bulb or repair
connector contact

License plate light bulb
continuity

Bulb burned out or poor
connector contact

NG
OK



4. Clearance light does not light

Replace the bulb or repair
connector contactClearance light bulb continuityBulb burned out or poor
connector contact
NG





BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-166 ELECTRICAL-BODY AND CHASSIS
LIGHTING SYSTEM
REMOVAL AND INSTALLATION


3 2
1
RTW 78ASH000101

FRONT COMBINATION LIGHT (A type)
Removal
1. Remove the radiator grille 1.
Refer to the removal procedure of the RADIATOR GRILLE
in Section 2B “SHEET METAL”.
2. Remove the front bumper
3.
Refer to the removal procedure of the FRONT BUMPER in
Section 2A “FRAME AND BUMPER”.
3. Disconnect the headlight connector.
4. Disconnect the clearance light connector.
5. Disconnect the turn signal light connector.
6. Remove the front combination light assembly
2.
• Remove four fixing screws.



HEADLIGHT ASSEMBLY (B type)
Removal
1. Open the bonnet.
2. Remove the front combination light assembly. • Refer to "Front Combination Light Assembly" removal
procedure in this section.
3. Remove the radiator grille. • Refer to "Radiator grille" removal procedure in 2B
section.
4. Remove the front bumper. • Refer to "Front Bumper" removal procedure in 2B
section.
5. Disconnect headlight bulb connectors.

RTW 580SH0008001
6. Remove the bolts of headlight assembly. 7. Remove the headlight assembly.



Installation
To install the front combination light assembly, follow the
removal procedure in reverse order.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-167


HEADLIGHT (HALOGEN STD TYPE)
(A type)
Removal
1. Remove the head light socket.
2. Remove the headlight dust cover.


3. Slide out the lock spring.


4. Remove the bulb.



1
RTW 78ASH000801

HEADLIGHT (HALOGEN PROJECTOR
TYPE)
Removal
1. Remove the head light socket.
2. Remove the headlight dust cover
1.



1

RTW 78ASH000901
3. Turn the bulb socket counterclockwise to remove it.
4. Remove the headlight bulb
1.

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-168 ELECTRICAL-BODY AND CHASSIS
HALOGEN HEADLIGHT BULB (B type)
Removal
1. Open the bonnet.
2. Disconnect the headlight bulb connectors.

RTW 580SH000101
3. Turn the bulb counterclockwise to remove it.


Installation
To install the headlight, follow the removal procedure in
reverse order.
Pay close attention to the important points mentioned in the
following paragraphs.

Connector
Be absolutely sure that the headlight connector is securely
connected.
This will prevent a contact and an open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-169
Installation
Follow the removal procedure in the reverse order to install the
headlight.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the headlight connector is securely
connected.
This will prevent a contact and an open circuit.



RTW 780SH000901
This illustration is based on RHD model

LIGHTING SWITCH
Removal
1. Disconnect the battery ground cable.
2. Remove the steering wheel
1.
Refer to the “STEERING” Section of this manual.
3. Remove the Instrument panel lower cover
2.
4. Remove the steering column cover
3.




RTW 780SH001001
This illustration is based on RHD model
5. Disconnect the connector.
6. Remove the lighting switch
4 from the steering shaft.





Installation
Follow the removal procedure in the reverse order to install the
lighting switch.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the lighting switch connector is securely
connected.
This will prevent a poor contact and an open circuit.


Wire Harness
Do not pinch the wire harnesses between the cluster and the
meter hood during the cluster installation procedure.
W ire damage will result.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007