2007 ISUZU KB P190 Circuit

ELECTRICAL-BODY AND CHASSIS 8A-139

CIRCUIT DIAGRAM 4JH1-TC (LHD) Sheet 2/2






RTW 78AXF004701


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-140 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION

ECM (ENGINE CONTROL MODULE);
C24SE

Removal
1. Lift both the ECM harness connector locking levers and
remove the two harness connectors form the ECM.
2. Remove the four socket head screws securing the ECM to the mounting bracket.
3. Remove the ECM from the engine compartment .


4. Pull out the ECM.
5. Disconnect both red and tan connectors.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobilizer
programming (if equipped) is/are necessary”





Installation
Follow the removal procedure in the reverse order to install the
ECM.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-141
REMOVAL AND INSTALLATION

ECM (ENGINE CONTROL MODULE);
4JH1-TC


Removal
1. Remove the passenger side front seat – refer to Section 10
CAB.
2. Remove the passenger side front door opening scuff plate.
3. Raise the carpet to gain access to the four hex-head bolts securing the ECM and ECM cover to the floor pan .
4. Remove the four hex-head bolts.
5. Pull the two harness connector locks away from the harness connectors and then remove the connectors form
the ECM.
6. Remove the ECM from the vehicle.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobilizer
programming (if equipped) is/are necessary”







Installation
Follow the removal procedure in the reverse order to install the
ECM.
Torque passenger seat securing bolts to the specified value –
refer to Section 10 CAB
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-142 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION



FUEL GAUGE UNIT AND SENDER
ASSEMBLY
Removal
1. Remove the fuel gauge unit and sender assembly.
Refer to the “ENGINE FUEL” Section 6C of this Manual.





Installation
To install the fuel gauge unit and sender assembly, follow the
removal procedure in reverse order.
Pay close attention to the important points mentioned in the
following paragraphs.



Rubber Seal
Be absolutely sure that the fuel sender rubber seals are
correctly seated.

Connector
Be absolutely sure that the fuel gauge unit connector is
securely connected.
This will prevent a poor contact and an open circuit.




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-147

CIRCUIT DIAGRAM 4JA1T (L)
Sheet 1/2


RTW 78AXF008401

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-148 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM 4JA1T (L)
Sheet 2/2





RTW 78AXF008501

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-151

CIRCUIT DIAGRAM C24SE (RHD)



RTW 780XF012201

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-152 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM C24SE (LHD) WITHOUT HEADLIGHTS LEVELING


RTW 680XF006701

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007