2007 ISUZU KB P190 Circuit

ELECTRICAL-BODY AND CHASSIS 8A-187

RTW 780SH000601
FOG LIGHT (A type)
Removal
1. Disconnect the fog light connector 1 .
2. Remove two attaching nuts
2.
3. Pull the fog light assembly toward the vehicle front to remove it from the holding bracket
3 .
4. Remove the bulb with socket. • Turn the socket
4 counterclockwise to remove it.
5. Remove the bulb. • Release the lock spring.
• Pull out the bulb.


FOG LIGHT (B type)
Removal
1. Remove the radiator grille.
2. Remove the front bumper
3. Disconnect the fog light connector.
4. Remove the fog light.


5. Remove the bulb from the socket.
• Remove the cover by turning it counterclockwise out
side the lock spring.
• Remove the bulb.



Hold the bulb by the flange when replacing it.
Do not touch the bulb with your hands.

Installation
To install the fog light, follow the removal procedure in reverse
order.
Pay close attention to the important points mentioned in the
following paragraphs.





Bulb
Be absolutely sure that the fog light bulb is correctly installed.
This will prevent a poor contact and open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-192 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM 4JJ1-TC/4JK1-TC (LHD) G.EXP


RTW 78AXF023101


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-193




RTW 48ASH000701

REAR FOG LIGHT
Removal
1. Remove the screws 1.
2. Remove the lens cover
2.
3. Rear fog push turn the bulb
3 counterclockwise to
disconnect it from the light housing.



Installation
Follow the removal procedure in the reverse order to install the
rear fog light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the license plate light bulb is correctly
installed.
This will prevent a poor contact and open circuit.




RTW 78ASH000401
FRONT FOG & RR FOG SWITCH



RTW 48ASH000401
Inspection
Check to see if there is any continuity between the terminals of
the leveling switch.
Replace the switch when the result of inspection is found
abnormal.

Removal
Preparation:
Disconnect the battery ground cable.
1. Ventilation grille
2. Harness connector
3. Front fog light & Rear fog light switch To remove the switch, push the lock from the back side of
the cluster assembly.
4. Remove the bulb.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-196 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM C24SE (RHD)


RTW 680XF007601

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-197

CIRCUIT DIAGRAM C24SE (LHD)


RTW 680XF007501

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-198 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM 4JJ1-TC / 4JK1-TC EXCEPT SOUTH AFRICA, 4JA1T (L) (LHD)



RTW 78AXF023001


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-202 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM C24SE (RHD) WITHOUT ILLUMINATION CONTROL





RTW 680XF007701

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-203

CIRCUIT DIAGRAM C24SE (RHD) WITH ILLUMINATION CONTROL







RTW 680XF007801


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007