Page 5196 of 6020
8A-258 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM 4JA1T (L)
RTW 78AXF005901
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5197 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-259
TROUBLESHOOTING
1. Dome light dose not light
Checkpoint Trouble Cause Countermeasure
Replace the dome light bulb
Burned out the bulb
NG
Repair or replace the dome
light assembly
Dome light switch function
Switch malfunction
Repair open circuit or
connector contact
Continuity between
connector 5
H12 - 1 L1
Open circuit or poor connector
contact
NG
NG
OK
OK
Dome light bulb continuity
2. Dome light does not go out
Repair or replace the door
switch
Switch malfunction or foreign
material switch
NG
Repair short circuit or
connector contact
Continuity between
connector 2
L1 -ground
when shutting the door
(Should be no continuity)
Short circuit
NG
OK
Door switch function (Both
side)
BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007
Page 5198 of 6020
8A-260 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION
DOME LIGHT
Removal
1. Remove the dome light lens 1 free.
2. Remove two dome light fixing screws.
3. Remove the wiring connector.
4. Remove the dome light.
5. Pull the bulb
2 to remove it.
Installation
Follow the removal procedure in the reverse order to install the
dome light.
Pay close attention to the important points mentioned in the
following paragraphs.
Bulb
Be absolutely sure that the dome light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5199 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-261
DOOR SWITCH
Removal
1. Disconnect the battery ground cable.
2. Loosen the screw
1.
3. Remove the door switch
2.
4. Disconnect the door switch connector
3.
Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the door switch connector is securely
connected.
This will prevent a poor contact and an open circuit.
SPOTLIGHT (MAP Light)
Removal
1. Grasp the spotlight housing 1 with both hands.
Pull the housing straight down.
This will release the clip.
2. Disconnect the connector
2.
3. Turn socket
3 counterclockwise to remove it.
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5200 of 6020
8A-262 ELECTRICAL-BODY AND CHASSIS
Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the spot light connector is securely
connected.
This will prevent a poor contact and an open circuit.
Bulb
Be absolutely sure that the spot light bulb is correctly installed.
This will prevent a poor contact and an open circuit.
RUW 580SH001501
RUW 580SH001601
OVER HEAD CONSOLE (MAP Light)
Removal
1. Open the lid (1) and remove the fastener (2).
2. A steel scale equivalent article is inserted in a lens side hook part and the crevice A section with roof lining, a metal
clip (5) is pushed in, and a over head consol (3) is removed
3. Disconnect the connector.
4. Push the bulb socket (4) in and turn it counterclockwise to remove it.
Installation
Follow the removal procedure in the reverse order to install the
front map light.
Pay close attention to the important points mentioned in the
following paragraphs.
Bulb
Be absolutely sure that the front map light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5201 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-263
INSPECTION AND REPAIR
R9 R10
R1 R6
DOOR SWITCH
Door Switch Connections
Connector
SW No.
R9
R10
R1 R6
position Terminal No.
1 Body Ground
PUSHED
RELEASED
W arning function Operational conditions
Key left in starter switch The buzzer sounds when both the key remind switch and the front door
switch-driver side are turned on.
To stop the sound of the buzzer, turn OFF the starter switch and remove the
key from the starter switch.
Lighting switch left on The buzzer sounds when the starter switch is turned from the “ON” to “OFF”
position while the lighting switch is ON position.
To stop the sound of the buzzer, turn OFF the lighting switch.
B62 B63
KEY REMIND SWITCH (STARTER
SWITCH)
Switch Connections
Connector
No. B63
Starter Terminal
switch key position No.
2 4
Removed
OFF
ACC Inserted
ON
START
LOCK
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5202 of 6020
8A-264 ELECTRICAL-BODY AND CHASSIS
WINDSHIELD WIPER AND WASHER
PARTS LOCATION (RHD)
RTW 78AXF038101 & RTW 78AXF044301
BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007
Page 5203 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-265
PARTS LOCATION (LHD)
RTW 78AXF038201 & RTW 78AXF044401
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
