2007 ISUZU KB P190 Electrical

8A-282 ELECTRICAL-BODY AND CHASSIS
This illustration is based on RHD model


8. Remove the wiper linkage
7 from the access hole.






Installation
Follow the removal procedure in the reverse order to install the
wiper motor and linkage.
Pay close attention to the important points mentioned in the
following paragraphs.








Wiper Linkage
Take care not to scratch the painted surfaces of the body when
installing the wiper linkage to the body.
In case crank arm of wiper motor is removed, confirm the
position of auto stop prior to reinstall the crank arm to the wiper
motor.
Crank Arm Nut Torque N⋅m (kg ⋅m/lb ft
)
20 − 26 (2.0 − 2.6 / 14.5 − 18.8)

880R300006





Wiper Blade Position
Confirm the auto stop position of wiper motor prior to the
installation of the wiper blade and arm.
The distance between the vent cowl cover rubber seal
1 and
the wiper blade edge
2 is about 52±7.5 mm (2.05 ±0.3 in) 3
40 ±7.5 mm (1.57 ±0.3 in).




Wiper Arm Nut
Tighten the wiper arm nut to the specified torque.
W iper Arm Nut Torque N ⋅m (kg ⋅m/lb ft)
27 − 35 (2.75 − 3.57/19.94 − 25.85)


This illustration is based on RHD model

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-283
Windshield Washer Spray
Be sure that the engine hood is completely closed before
checking the windshield washer spray adjustment.
W indshield W asher Spray Position: Refer to the illustration.

RTW 38DSF000201



Connector
Be absolutely sure that the wiper motor connector is securely
connected.
This will prevent a poor contact and an open circuit.



Note:
Windshield wiper arm and blade assembly configurations
are different for the right-hand and left-hand side of the
vehicle.
Be careful not to confuse the right-hand and left-hand side
assemblies.



This illustration is based on RHD model
WASHER TANK MOTOR
Removal
1. Remove the head light.
• Refer to the head light in this manual.
2. Remove the inner liner.
3. Pull out the clip washer filler.
4. Remove the washer tank nuts.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-284 ELECTRICAL-BODY AND CHASSIS


4. Disconnect the connector
1.
5. Disconnect the water hose
2.

6. Pull out the washer tank motor 3.




Installation
Follow the removal procedure in the reverse order to install the
washer tank motor.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the washer tank motor connector is
securely connected.
This will prevent a poor contact and an open circuit.




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-285
TRANSMISSION CONTROL MODULE (TCM)
PARTS LOCATION (RHD)





RTW 78AXF038301 & RTW 78AXF044501

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-286 ELECTRICAL-BODY AND CHASSIS

PARTS LOCATION (LHD)






RTW 78AXF038401 & RTW 78AXF044801

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-287

PARTS LOCATION 4JJ1-TC


RTW 78AXF048601

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-288 ELECTRICAL-BODY AND CHASSIS

PARTS LOCATION 4JH1-TC






















RTW 78AXF049401

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-289

PARTS LOCATION















RTW 78AXF035701

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007