2007 INFINITI QX56 ignition

TROUBLE DIAGNOSISATC-115
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
DIAGNOSTIC PROCEDURE FOR AMBIENT SENSOR
SYMPTOM: Ambient sensor circui t is open or shorted. Using the
CONSULT-II, DTC B257B or B257C is displayed. Without a CON-
SULT-II, code 40 or 41 is indicated on front air control as a result of
conducting the front air control self-diagnosis.
1.CHECK VOLTAGE BETWEEN AMBIENT SENSOR AND GROUND
1. Disconnect ambient sensor connector.
2. Turn ignition switch ON.
3. Check voltage between ambient sensor harness connector E1 terminal 1 and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 4.
2.CHECK CIRCUIT CONTINUITY BETWEEN AMBIENT SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check continuity between am bient sensor harness connector
E1 terminal 1 and front air control harness connector M49 termi-
nal 17.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK AMBIENT SENSOR
Refer to "Ambient Sensor Circuit" .
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation"
2. Go to ATC-48, "A/C System Self-Diagnosis Function" and perform self-diagnosis.
NG >> 1. Replace ambient sensor. Refer to ATC-124
.
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
4.CHECK CIRCUIT CONTINUITY BETWEEN AMBIENT SENSOR AND FRONT AIR CONTROL
WJIA0456E
1 - Ground : Approx. 5V
WJIA1273E
1 - 17 : Continuity should exist.
WJIA0564E

ATC-116
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check continuity between ambient sensor harness connector
E1 terminal 2 and front air control harness connector M49 termi-
nal 21.
4. Check continuity between am bient sensor harness connector
E1 terminal 2 and ground.
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation"
2. Go to self-diagnosis ATC-48, "A/C System Self-Diagnosis Function" and perform self-diagno-
sis.
NG >> Repair harness or connector.
COMPONENT INSPECTION
Ambient Sensor
After disconnecting ambient sensor (1) connector E1, measure
resistance between terminals 1 and 2 at sensor component side,
using the table below.
If NG, replace ambient sensor.
In-vehicle Sensor CircuitINFOID:0000000003533267
COMPONENT DESCRIPTION
In-vehicle Sensor
2 - 21 : Continuity should exist.
2 - Ground : Continuity should not exist.
WJIA0565E
Temperature °C ( °F) Resistance k Ω
− 15 (5) 12.73
− 10 (14) 9.92
− 5 (23) 7.80
0 (32) 6.19
5 (41) 4.95
10 (50) 3.99
15 (59) 3.24
20 (68) 2.65
25 (77) 2.19
30 (86) 1.81
35 (95) 1.51
40 (104) 1.27 45 (113) 1.07
WJIA1975E

TROUBLE DIAGNOSISATC-117
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
The in-vehicle sensor is located on cluster lid D. It converts varia-
tions in temperature of passenger compartment air (drawn in through
the integrated fan) into a resistance value. It is then input into the
front air control.
DIAGNOSTIC PROCEDURE FOR IN-VEHICLE SENSOR
SYMPTOM: In-vehicle sensor circui t is open or shorted. Using the
CONSULT-II, DTC B2578 or B2579 is displayed. Without a CON-
SULT-II code 30, 31, 44 or 46 is indicated on front air control as a
result of conducting self-diagnosis.
1.CHECK IN-VEHICLE SENSOR CIRCUIT
Self-diagnosis DTC B2578 or B2579 (with CONSULT-II ) or code 30, 31 44 or 46 (without CONSULT-II) is
present?
YES or NO
YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK VOLTAGE BETWEEN IN-VEHICLE SENSOR AND GROUND
1. Disconnect in-vehicle sensor connector.
2. Turn ignition switch ON.
3. Check voltage between in-vehicle sensor harness connector M32 terminal 4 and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3.CHECK CIRCUIT CONTINUITY BET WEEN IN-VEHICLE SENSOR AND FRONT AIR CONTROL
WJIA0822E
WJIA0606E
WJIA0460E
4 - Ground : Approx. 5V.
LJIA0089E

ATC-118
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between in-vehicle sensor harness connectorM32 terminal 1 and front air control harness connector M49 ter-
minal 21.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4.CHECK IN-VEHICLE SENSOR
Refer to "In-vehicle Sensor Circuit" .
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation" .
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
NG >> 1. Replace in-vehicle sensor. Refer to ATC-125
.
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
5.CHECK CIRCUIT CONTINUITY BETWEEN IN- VEHICLE SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check continuity between in-vehicle sensor harness connector M32 terminal 4 and front air control harness connector M50 ter-
minal 32.
4. Check continuity between in-vehicle sensor harness connector M32 terminal 4 and ground.
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation" .
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
NG >> Repair harness or connector.
6.CHECK CIRCUIT CONTINUITY BETWEEN IN-VEHIC LE SENSOR MOTOR AND FRONT AIR CONTROL
(SELF-DIAGNOSIS CODES 30, 31, 44, 46 OR DTC B2578, B2579)
1. Turn ignition switch OFF.
2. Disconnect front air control connector and in-vehicle sensor con- nector.
3. Check continuity between in-vehicle sensor harness connector M32 terminal 2 and 3 and front air control harness connector
M50 terminal 44 and 43.
4. Check continuity between in-vehicle sensor harness connector M32 terminal 2 and 3 and ground.
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation" .
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
NG >> Repair harness or connector. 1 - 21 : Continuity should exist.
LJIA0090E
4 - 32 : Continuity should exist.
4 - Ground Continuity should not exist.
LJIA0091E
2 - 44 : Continuity should exist.
3 - 43 : Continuity should exist.
2, 3 - Ground :Continuity should not exist.
LJIA0093E

ATC-120
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
SYMPTOM: Optical sensor circuit is open or shorted. Using the
CONSULT-II, DTC B257F or B2580 is displayed. Without a CON-
SULT-II, code 50 or 52 is indicated on front air control as a result of
conducting the front air control self-diagnosis.
1.CHECK CIRCUIT CONTINUITY BETWEEN OPTI CAL SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector and optical sensor con- nector.
3. Check continuity between opt ical sensor harness connector
M402 terminal 1 and 2 and front air control harness connector
M50 terminal 31 and 40.
4. Check continuity between opt ical sensor harness connector
M402 terminal 1 and 2 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK CIRCUIT CONTINUITY BETW EEN OPTICAL SENSOR AND BCM
1. Turn ignition switch OFF.
2. Disconnect BCM connector and optical sensor connector.
3. Check continuity between opt ical sensor harness connector
M402 terminal 3 and BCM harness connector M18 terminal 18.
4. Check continuity between opt ical sensor harness connector
M402 terminal 3 and ground.
OK or NG
OK >> Replace optical sensor. Refer to ATC-126 .
NG >> Repair harness or connector.
Intake Sensor CircuitINFOID:0000000003533269
COMPONENT DESCRIPTION
Intake Sensor
WJIA0570E
1 - 31 : Continuity should exist.
2 - 40 : Continuity should exist.
1, 2 - Ground. : Contin uity should not exist.
WJIA1445E
3 - 18 : Continuity should exist.
3 - Ground : Continuity should not exist.
WJIA1446E

TROUBLE DIAGNOSISATC-121
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
The intake sensor is located on the heater & cooling unit. It converts
temperature of air after it passes through the evaporator into a resis-
tance value which is then input to the front air control.
DIAGNOSTIC PROCEDURE FOR INTAKE SENSOR
SYMPTOM: Intake sensor circuit is open or shorted. Using the CON-
SULT-II, DTC B2581 or B2582 is di splayed. Without a CONSULT-II,
code 56 or 57 is indicated on front air control as a result of conduct-
ing the front air control self-diagnosis.
1.CHECK VOLTAGE BETWEEN INTAKE SENSOR AND GROUND
1. Disconnect intake sensor connector.
2. Turn ignition switch ON.
3. Check voltage between intake sensor harness connector M146 terminal 2 and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 4.
2.CHECK CIRCUIT CONTINUITY BETWEEN IN TAKE SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check continuity between intake sensor harness connector M146 terminal 1 and front air control harness connector M49 ter-
minal 21.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK INTAKE SENSOR
Refer to "Intake Sensor Circuit".
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation"
2. Go to ATC-48, "A/C System Self-Diagnosis Function" and perform self-diagnosis.
NG >> 1. Replace intake sensor. Refer to ATC-127
.
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
WJIA0571E
WJIA0464E
2 - Ground : Approx. 5V
WJIA1375E
1 - 21 : Continuity should exist.
WJIA1376E

ATC-122
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
4.CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check continuity between in take sensor harness connector
M146 terminal 2 and front air control harness connector M49 ter-
minal 9.
4. Check continuity between in take sensor harness connector
M146 terminal 2 and ground.
OK or NG
OK >> 1. Replace front air control. Refer to ATC-123, "Removal and Installation".
2. Go to ATC-48, "
A/C System Self-Diagnosis Function" and perform self-diagnosis.
NG >> Repair harness or connector.
COMPONENT INSPECTION
Intake Sensor
After disconnecting intake sensor connector, measure resistance
between terminals 1 and 2 at sensor harness side, using the table
below.
If NG, replace intake sensor. 2 - 9 : Continuity should exist.
2 - Ground : Continuity should not exist.
WJIA1377E
Temperature
°C ( °F) Resistance k Ω
− 15 (5) 209.0
− 10 (14) 160.0
− 5 (23) 123.0
0 (32) 95.8
5 (41) 74.9
10 (50) 58.9
15 (59) 46.7
20 (68) 37.3
25 (77) 30.0
30 (86) 24.2
35 (95) 19.7
40 (104) 16.1 45 (113) 13.2
WJIA1378E

ATC-170
< SERVICE INFORMATION >
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Service Data and Specification (SDS)INFOID:0000000003533311
COMPRESSOR
OIL
REFRIGERANT
ENGINE IDLING SPEED
Refer to EC-75, "Idle Speed and Ignition Timing Check".
BELT TENSION
Refer to EM-13, "Checking Drive Belts".
Make ZEXEL VALEO CLIMATE CONTROL
Model DKS-17D
Ty p e Swash plate
Displacement 175.5 cm
3 (10.7 in3 ) / revolution
Cylinder bore × stroke 30.5 mm (1.20 in) x 24.0 mm (0.94 in)
Direction of rotation Clockwise (viewed from drive end)
Drive belt Poly V
Name NISSAN A/C System Oil Type S
Capacity 290 m (9.8 US fl oz, 10.2 Imp fl oz)
Ty p eHFC 134a (R-134a)
Capacity 1.08 ± 0.05 kg (2.38 ± 0.11 oz)