2007 INFINITI M35 display

WT-18
TROUBLE DIAGNOSES
Revision: 2007 April2007 M35/M45
ID Registration ProcedureNES000JY
ID REGISTRATION WITH ACTIVATION TOOL
This procedure must be done after replacement of a tire pressure transmitter, low tire pressure warn-
ing control unit, or tire rotation.
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "
CONSULT-II Start Procedure" .
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Touch “ID REGIST” on “SELECT WORK ITEM”.
4. With the activation tool (J-45295) pushed against the front-left
tire pressure transmitter position of the tire air valve, press and
hold the button for 5 seconds.
5. Register the IDs in order from FR LH, FR RH, RR RH, RR LH.
When ID registration of each wheel has been completed, turn
signal lamp blinks.
6. After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnosis results
display will not function properly.
ID REGISTRATION WITHOUT ACTIVATION TOOL
This procedure must be done after replacement of a tire pressure transmitter, low tire pressure warn-
ing control unit, or tire rotation.
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "
CONSULT-II Start Procedure" .
2. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Touch “ID REGIST” on “SELECT WORK ITEM”.
4. Adjust the tire pressure to the values shown in the table below for ID registration, and drive the vehicle at
40 km/h (25 MPH) or more for a few minutes.
5. After completing all ID registrations, press “END” to complete the procedure.
6. Inflate all tires to proper pressure. Refer to WT-41, "
SERVICE DATA AND SPECIFICATIONS (SDS)" .
SEIA0460E
Activation tire position Turn signal lamp CONSULT-II
1 Front LH
2 times flashing“YET”
↓
“DONE” 2 Front RH
3Rear RH
4 Rear LH
Tire position
Tire pressure kPa (kg/cm2 , psi)
Front LH 240 (2.4, 34)
Front RH 220 (2.2, 31)
Rear RH 200 (2.0, 29)
Rear LH 180 (1.8, 26)
Activation tire position CONSULT-II
Front LH
“YET”
↓
“DONE” Front RH
Rear RH
Rear LH

TROUBLE DIAGNOSES
WT-19
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2007 April2007 M35/M45
Transmitter Wake Up OperationNES000JZ
WITH TRANSMITTER ACTIVATION TOOL
1. With the activation tool (J-45295) pushed against the front-left
transmitter, press and hold the button for 5 seconds.

When ignition switch ON, as the low tire pressure warning
lamp blinks per the follow diagram, the respective transmitter
then must be wake up.
2. Register the ID of wheel that warning lamp flashes. When wake up of registered wheel has been com-
pleted, turn signal lamp flashes two times.
3. After completing wake up all transmitters, make sure low tire pressure warning lamp goes out.
CONSULT-II Function (AIR PRESSURE MONITOR)NES000K0
DESCRIPTION
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II SETTING PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
SEIA0460E
SEIA0378E
Diagnostic test mode Function Reference
WORK SUPPORTThis mode enables a technician to adjust some devices faster and more
accurately by following the indications on CONSULT-II.WT-20, "
WORK SUP-
PORT MODE"
SELF-DIAG RESULTSReceives self-diagnosis results from low tire pressure warning control
unit and indicates DTCs. WT-20, "SELF-DIAG
RESULT MODE"
DATA MONITORReceives input/output signals from low tire pressure warning control
unit and indicates and stores them to facilitate locating cause of mal-
functions.WT-21, "DATA MONITOR
MODE"
CAN DIAG SUPPORT MNTR Monitors transmitting/receiving status of CAN communication.LAN-44, "CAN Diagnostic
Support Monitor"
ACTIVE TESTDiagnostic Test Mode in with CONSULT-II drives some actuators apart
from the low tire pressure warning control unit and also shifts some
parameters in a specified range.WT-22, "ACTIVE TEST
MODE"
ECU PART NUMBER Displays low tire pressure warning control unit part number. WT-22, "
LOW TIRE PRES-
SURE WARNING CON-
TROL UNIT PART
NUMBER"

WT-20
TROUBLE DIAGNOSES
Revision: 2007 April2007 M35/M45
WORK SUPPORT MODE
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. Perform the “ID Regist”. Refer to WT-18, "
ID Registration Procedure" .
SELF-DIAG RESULT MODE
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. The self-diagnostic results are displayed. (Touch “PRINT” to print out the self-diagnostic results if neces-
sary.) Check low tire pressure warning lamp if “NO FAILURE” is displayed.
3. Perform the appropriate inspection from the display item list, and repair or replace the malfunctioning
component. Refer to WT-20, "
Display Item List" .
Display Item List
DTCItems
(CONSULT-II screen terms)Diagnostic item is detected when ···Check
items
C1704 LOW PRESSURE FL
Front LH tire pressure drops to * kPa (* kg/cm
2 , * psi) or less. (Notice)
— C1705 LOW PRESSURE FR
Front RH tire pressure drops to * kPa (* kg/cm
2 , * psi) or less. (Notice)
C1706 LOW PRESSURE RR
Rear RH tire pressure drops to * kPa (* kg/cm
2 , * psi) or less. (Notice)
C1707 LOW PRESSURE RL
Rear LH tire pressure drops to * kPa (* kg/cm
2 , * psi) or less. (Notice)
C1708 [NO DATA] FL Data from front LH transmitter cannot be received.
WT-29
C1709 [NO DATA] FR Data from front RH transmitter cannot be received.
C1710 [NO DATA] RR Data from rear RH transmitter cannot be received.
C1711 [NO DATA] RL Data from rear LH transmitter cannot be received.
C1716 [PRESSDATA ERR] FL Air pressure data from front LH transmitter is malfunctioning.
WT-31
C1717 [PRESSDATA ERR] FR Air pressure data from front RH transmitter is malfunctioning.
C1718 [PRESSDATA ERR] RR Air pressure data from rear RH transmitter is malfunctioning.
C1719 [PRESSDATA ERR] RL Air pressure data from rear LH transmitter is malfunctioning.
C1720 [CODE ERROR] FL Function code data from front LH transmitter is malfunctioning.
WT-32
C1721 [CODE ERROR] FR Function code data from front RH transmitter is malfunctioning.
C1722 [CODE ERROR] RR Function code data from rear RH transmitter is malfunctioning.
C1723 [CODE ERROR] RL Function code data from rear LH transmitter is malfunctioning.
C1724 [BATT VOLT LOW] FL Battery voltage of front LH transmitter drops.
WT-32
C1725 [BATT VOLT LOW] FR Battery voltage of front RH transmitter drops.
C1726 [BATT VOLT LOW] RR Battery voltage of rear RH transmitter drops.
C1727 [BATT VOLT LOW] RL Battery voltage of rear LH transmitter drops.
C1728 RECEIVER ID NO REG ID registration of receiver is not completed.WT-33
C1729 VHCL SPEED SIG ERR Vehicle speed signal is error.WT-33
C1750 [RECEIVER ERR] FL Data from front LH receiver cannot be received.
WT-30
C1751 [RECEIVER ERR] FR Data from front RH receiver cannot be received.
C1752 [RECEIVER ERR] RR Data from rear RH receiver cannot be received.
C1753 [RECEIVER ERR] RL Data from rear LH receiver cannot be received.
C1754 CONTROL UNIT (EEPROM)When the malfunction is detected in low tire pressure warning control
unit memory [CONTROL UNIT (EEPROM)] function.WT-34
U1000 CAN COMM CIRCUITWhen a low tire pressure warning control unit is not transmitting or
receiving CAN communication signal 2 seconds or more. WT-34
U1010 CONTROL UNIT [CAN]When detecting error during the initial diagnosis of CAN controller of
low tire pressure warning control unit.WT-34

TROUBLE DIAGNOSES
WT-21
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2007 April2007 M35/M45
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction location may be different from that dis-
played on CONSULT-II.
NOTICE:
182 kPa (1.82 kg/cm
2 , 26.5 psi): Standard air pressure is for 230 kpa (2.3 kg/cm2 , 33 psi) vehicles.
How to Erase Self-Diagnostic Results
1. Perform applicable inspection of malfunctioning item and then repair or replace.
2. Start engine, and touch “START (NISSAN BASED VHCL)” “AIR PRESSURE MONITOR” “SELF-DIAG
RESULTS” “ERASE” in this order to erase the diagnostic memory.
CAUTION:
If memory cannot be erased, repeat step 1, 2.
3. Perform self-diagnosis again, and make sure that DTC memory is erased.
DATA MONITOR MODE
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. Touch “DATA MONITOR”.
3. Select from “SELECT MONITOR ITEM”, screen of data monitor is displayed.
NOTE:
When malfunction is detected, CONSULT-II performs REAL-TIME DIAGNOSIS. Also, any malfunction
detected while in this mode will be displayed in real time.
Display Item List
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction location may be different from that dis-
played on CONSULT-II.MONITOR CONDITION SPECIFICATION
VEHICLE SPEED SE Drive vehicle. Vehicle speed (km/h or MPH)
AIR PRESS FL
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL

Drive vehicle for a few minutes.
Tire pressure (kPa or Psi) or

Ignition switch ON and activation tool is
transmitting activation signals.
ID REGST FL
ID REGST FR
ID REGST RR
ID REGST RL
Ignition switch ONRegistration ID: DONE
No registration ID: YET
WARNING LAMPLow tire pressure warning lamp on: ON
Low tire pressure warning lamp off: OFF
BUZZERBuzzer in combination meter on: ON
Buzzer in combination meter off: OFF

WT-22
TROUBLE DIAGNOSES
Revision: 2007 April2007 M35/M45
ACTIVE TEST MODE
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. “ACTIVE TEST” is displayed.
Display Item List
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction location may be different from that dis-
played on CONSULT-II.
LOW TIRE PRESSURE WARNING CONTROL UNIT PART NUMBER
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. The part number described on low tire pressure warning control unit sticker is displayed.
Diagnosis Procedure with Warning Lamp Function (Without CONSULT-II)NES000K6
DESCRIPTION
During driving, the tire pressure monitoring system receives the signal transmitted from the transmitter
installed in each wheel when the tire pressure becomes low. The control unit (low tire pressure warning control
unit) of this system has pressure judgement and trouble diagnosis functions.
FUNCTION
When the tire pressure monitoring system detects low inflation pressure or another unusual symptom, the
warning lamps in the combination meter comes on. To start the self-diagnostic results mode, ground terminal
of the tire pressure warning check connector. The malfunction location is indicated by the warning lamp flash-
ing. Regarding location of tire pressure warning check connector, refer to PG-62, "
HARNESS" .
Test item Content
BUZZER This test is able to check to make sure that the buzzer sounds.
WARNING LAMP This test is able to check to make sure that the warning lamp turns on.

TROUBLE DIAGNOSIS FOR SYSTEM
WT-29
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2007 April2007 M35/M45
TROUBLE DIAGNOSIS FOR SYSTEMPFP:00000
Transmitter no DataNES000KA
MALFUNCTION CODE NO. 21, 22, 23, 24
1. CHECK CONTROL UNIT
Drive for several minutes. Check all tire pressures with CONSULT-II “DATA MONITOR”.
Are all tire pressures displayed 0 kPa?
YES >> GO TO 2.
NO >> GO TO 3.
2. CHECK TIRE PRESSURE RECEIVER CONNECTOR
1. Disconnect tire pressure receiver harness connector E74 (FR-LH), E75 (FR-RH), B482 (RR-RH), B115
(RR-LH).
2. Check terminals for damage or loose connection.
3. Reconnect harness connector.
OK or NG
OK >> Replace low tire pressure warning control unit. Refer to WT-40, "Low Tire Pressure Warning Con-
trol Unit" , then GO TO 3.
NG >> Repair or replace tire pressure receiver harness connector.
3. ID REGISTRATION
Perform ID registration of all transmitters.
Are there any tires that ID can not be registered to?
YES >> Replace transmitter of the tire, then GO TO 5.
NO >> GO TO 4.
4. VEHICLE DRIVING
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
Check all tire pressures with CONSULT-II “DATA MONITOR” within 15 minutes after vehicle speed becomes
17 km/h (11 MPH).
Does
“DATA MONITOR ” display tire pressure as normal without any warning lamp?
YES >>INSPECTION END
NO >> GO TO 5.
5. ID REGISTRATION AND VEHICLE DRIVING
1. Perform ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tire pressures with CONSULT-II “DATA MONITOR” within 5 minutes.
Does
“DATA MONITOR” display tire pressure as normal without any warning lamp?
YES >>INSPECTION END
NO >> GO TO the inspection applicable to DTC.

WT-30
TROUBLE DIAGNOSIS FOR SYSTEM
Revision: 2007 April2007 M35/M45
Receiver Data ErrorNES000KB
MALFUNCTION CODE NO. 25, 26, 27, 28
1. CHECK LOW TIRE PRESSURE WARNING CONTROL UNIT AND RECEIVER CONNECTOR
1. Turn ignition switch OFF, disconnect low tire pressure warning control unit harness connector and receiver
harness connector, and check terminal for deformation, disconnection, looseness, and so on. If there is a
malfunction, repair or replace the terminal.
2. Reconnect harness connector securely, and perform self-diagnosis.
Does
“SELF-DIAG RESULTS” display as normal without any warning lamp?
YES >> Connector terminal connection is loose, damaged, open, or shorted.
NO >> GO TO 2.
2. CHECK TIRE PRESSURE RECEIVER POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF, and disconnect tire pressure receiver harness connector E74, E75, B115, B482.
2. Check continuity between tire pressure receiver harness con-
nector E74, E75, B115, B482 and ground.
3. Turn ignition switch ON, and then check voltage between tire
pressure receiver harness connector E74, E75, B115, B482 and
ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
3. CHANGE THE TIRE PRESSURE RECEIVER POSITION (EXAMPLE OF FRONT LH SIDE)
1. Replace right from left for front and rear receivers.
2. Perform self-diagnosis.
Is the initial indication of self-diagnosis displayed?
YES >> GO TO 4
NO >> Replace tire pressure receiver front RH when indicating RH tire pressure receiver malfunction.Terminal 4 – Ground : Continuity should exist.
SGIA1249E
1 – Ground : Battery voltage (Approx.12 V)
SGIA1250E

TROUBLE DIAGNOSIS FOR SYSTEM
WT-31
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2007 April2007 M35/M45
4. CHECK RECEIVER HARNESS (EXAMPLE OF FRONT LH SIDE)
1. Turn ignition switch OFF, disconnect low tire pressure warning
control unit harness connector M19 (A) and receiver harness
connector E74 (B).
2. Check continuity between low tire pressure warning control unit
harness connector M19 (A) and receiver harness connector E74
(B).
OK or NG
OK >> Replace low tire pressure warning control unit.
NG >> Harness between Low tire warning control unit and receiver open or shorted. Repair or replace
harness.
Transmitter Pressure Data ErrorNES000KC
MALFUNCTION CODE NO. 35, 36, 37, 38
1. CHECK ALL TIRE PRESSURES
Check all tire pressures. Refer to WT-41, "
SERVICE DATA AND SPECIFICATIONS (SDS)" .
Are there any tires whose pressure is
“64 psi” or more?
YES >> Adjust tire pressure to specified value.
NO >> GO TO 2.
2. VEHICLE DRIVING
1. Perform ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
Check all tire pressures with CONSULT-II “DATA MONITOR” within 15 minutes after vehicle speed
becomes 17 km/h (11 MPH).
>> Replace tire pressure transmitter with new one if “DATA MONITOR” display 64 psi or more. Then
GO TO 3.
3. ID REGISTRATION AND VEHICLE DRIVING
1. Perform ID registration of all tire pressure transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tire pressures with CONSULT-II “DATA MONITOR” within 5 minutes.
Does
“DATA MONITOR” display tire pressure as normal without any warning lamp?
YES >>INSPECTION END
NO >> GO TO the inspection applicable to DTC.Terminal 27 – 2 : Continuity should exist.
Terminal 11 – 3 : Continuity should exist.
SEIA0789E