2007 INFINITI M35 rear entertainment

DIAGNOSIS SYSTEM
AV-107
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2007 April2007 M35/M45
AUDIO

When “AUDIO” is selected, the communication condition from
audio unit to each unit and malfunction counter are displayed.

Error counter displays OK if any malfunction is not detected in
the past. If the malfunction is detected, it displays 0. When turn-
ing the ignition switch ON, if it is normal, it displays 1. The upper
limit of the counter is 39.
ECU PART NUMBER
The part number of AV (NAVI) control unit is displayed.
STEERING SW OK / UNKWN OK / 0 - 39
AUDIO OK / UNKWN OK / 0 - 39
SPEAKER AMP OK / UNKWN OK / 0 - 39
SIDE CAMERA - -
REAR CAMERA OK / UNKWN OK / 0 - 39
TV TUNER - -
DVD PLAYER OK / UNKWN OK / 0 - 39
VIDEO DIST - -
ETC - -
FM MULTI - -
REMOTE CONT - -Items Display (PRSNT) Error counter (PAST)
Items Display (Current) Error counter (Past)
TRANSMIT DG OK / UNKWN OK / 0 - 39
SPEAKER AMP OK / UNKWN OK / 0 - 39
TV TUNER - -
DVD PLAYER OK / UNKWN OK / 0 - 39
MD DECK - -
CD CHANGER - -
MD CHANGER - -
SKIB3679E
SKIB3680E

TROUBLE DIAGNOSIS
AV-109
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2007 April2007 M35/M45
RGB Screen Is RollingNKS00492
1. CHECK HARNESS
1. Disconnect AV (NAVI) control unit connector and front display unit connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminal 45 and front display unit harness con-
nector (B) M203 terminal 3.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminal 45 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK RGB SIGNAL (G: GREEN)
1. Connect AV (NAVI) control unit connector and front display unit connector.
2. Turn ignition switch ON.
3. Start Confirmation/Adjustment mode. Refer to AV- 9 1 , "
Confirmation/Adjustment Mode" .
4. Display color bar by selecting “Display Color Spectrum Bar” on DISPLAY DIAGNOSIS screen. Refer to
AV- 9 1 , "
DISPLAY DIAGNOSIS" .
5. Check signal between AV (NAVI) control unit harness connector
M210 terminal 45 and ground.
OK or NG
OK >> Replace front display unit.
NG >> Replace AV (NAVI) control unit.
Rear View Monitor Image Is Not DisplayedNKS00493
DVD IMAGE IS DISPLAYED
1. CONSULT-II DIAGNOSIS
Perform CONSULT-II self-diagnosis and check the malfunction. Refer to AV- 1 0 3 , "
SELF-DIAG RESULTS" .
Is there a malfunction?
YES >> Refer to AV- 1 0 3 , "Display Item of SELF-DIAG RESULTS" .
NO >> GO TO 2.
2. REVERSE SIGNAL INSPECTION
1. Turn the ignition switch ON, and then select “Connection Confirmation” of “Camera Controller” on Confir-
mation/Adjustment mode.
2. Make sure that “Reverse Sensor” is turned ON when shifting the selector lever in R position.
Is it OK?
YES >> GO TO 3.
NO >> Check reverse signal circuit, and then repair the malfunctioning parts.45 – 3 : Continuity should exist.
45 – Ground : Continuity should not exist.
SKIB4692E
45 – Ground:
SKIB4693E
SKIB2236J

AV-110
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
3. CHECK HARNESS BETWEEN CAMERA CONTROL UNIT AND REAR VIEW CAMERA
1. Turn ignition switch OFF.
2. Disconnect camera control unit connector and rear view camera connector.
3. Check continuity between camera control unit harness connec-
tor (A) B481 terminal 8 and rear view camera harness connec-
tor (B) T109 terminal 1.
4. Check continuity between camera control unit harness connec-
tor (A) B481 terminal 8 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK REAR VIEW CAMERA POWER SUPPLY
1. Connect camera control unit connector and rear view camera connector.
2. Turn ignition switch ON.
3. Shift the selector lever in R position.
4. Check voltage between camera control unit harness connector
B481 terminal 8 and ground.
OK or NG
OK >> GO TO 5.
NG >> Replace camera control unit.
5. CHECK HARNESS BETWEEN CAMERA CONTROL UNIT AND REAR VIEW CAMERA
1. Turn ignition switch OFF.
2. Disconnect camera control unit connector and rear view camera connector.
3. Check continuity between camera control unit harness connec-
tor (A) B481 terminal 6 and rear view camera harness connector
(B) T109 terminal 3.
4. Check continuity between camera control unit harness connec-
tor (A) B481 terminal 6 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.8 – 1 : Continuity should exist.
8 – Ground : Continuity should not exist.
SKIB4607E
8 – Ground : Approx. 6 V
SKIB4608E
6 – 3 : Continuity should exist.
6 – Ground : Continuity should not exist.
SKIB4609E

TROUBLE DIAGNOSIS
AV-111
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2007 April2007 M35/M45
6. CHECK REAR VIEW IMAGE SIGNAL
1. Connect camera control unit connector and rear view camera connector.
2. Turn ignition switch ON.
3. Shift the selector lever in R position.
4. Check signal between camera control unit harness connector
B481 terminal 6 and ground.
OK or NG
OK >> GO TO 7.
NG >> Replace rear view camera.
7. HARNESS CHECK BETWEEN CAMERA CONTROL UNIT AND FRONT DISPLAY UNIT
1. Turn ignition switch OFF.
2. Disconnect camera control unit connector and front display unit connector.
3. Check continuity between camera control unit harness connec-
tor (A) B481 terminal 12 and front display unit harness connec-
tor (B) M203 terminal 11.
4. Check continuity between camera control unit harness connec-
tor (A) B481 terminal 12 and ground.
OK or NG
OK >> GO TO 8.
NG >> Repair harness or connector.
8. CHECK REAR VIEW IMAGE SIGNAL
1. Connect camera control unit connector and front display unit connector.
2. Turn ignition switch ON.
3. Shift the selector lever in R position.
4. Check signal between front display unit harness connector
M203 terminal 11 and ground.
OK or NG
OK >> Replace front display unit.
NG >> Replace camera control unit.6 – Ground:
SKIB4610E
SKIB2251J
12 - 11 : Continuity should exist.
12 - Ground : Continuity should not exist.
SKIB4611E
11 – Ground:
SKIB4612E
SKIB2251J

AV-112
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
DVD IMAGE IS NOT DISPLAYED
1. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND FRONT DISPLAY UNIT
1. Disconnect AV (NAVI) control unit connector and front display unit connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminal 50 and front display unit harness con-
nector (B) M203 terminal 2.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK RGB AREA SIGNAL
1. Connect AV (NAVI) control unit connector and front display unit connector.
2. Turn ignition switch ON.
3. Shift the selector lever in R position.
4. Check signal between AV (NAVI) control unit harness connector
M210 terminal 50 and ground.
OK or NG
OK >> Replace front display unit.
NG >> Replace AV (NAVI) control unit.
IT CANNOT BE SWITCHED TO REAR VIEW MONITOR IMAGE
1. CHECK REVERSE SIGNAL
Select “Vehicle Signals” on Confirmation/Adjustment mode, and make sure that the reverse signal is input nor-
mally. Refer to AV- 9 2 , "
VEHICLE SIGNALS" .
OK or NG
OK >> GO TO 2.
NG >> Check reverse signal circuit, and then repair the malfunctioning parts.50 – 2 : Continuity should exist.
SKIB4694E
50 – Ground:
SKIB4594E
PKIB4948J

TROUBLE DIAGNOSIS
AV-113
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2007 April2007 M35/M45
2. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND CAMERA CONTROL UNIT
1. Turn ignition switch OFF.
2. Disconnect AV (NAVI) control unit connector and camera control unit connector.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminal 67 and camera control unit harness
connector (B) B481 terminal 14.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK CAMERA-CONNECTION RECOGNITION SIGNAL
1. Connect AV (NAVI) control unit connector.
2. Turn ignition switch ON.
3. Check voltage between AV (NAVI) control unit harness connec-
tor M210 terminal 67 and ground.
OK or NG
OK >> Replace camera control unit.
NG >> Replace AV (NAVI) control unit.
DVD Image Is Not DisplayedNKS00494
1. REAR VIEW MONITOR IMAGE CONFIRMATION
Make sure that rear view monitor image is displayed when setting the selector lever in R position.
Is it displayed?
YES >> GO TO 2.
NO >> GO TO 4.
2. CHECK HARNESS BETWEEN DVD PLAYER AND FRONT DISPLAY UNIT
1. Turn ignition switch OFF.
2. Disconnect DVD player connector front display unit connector.
3. Check continuity between DVD player harness connector (A)
M272 terminal 20 and front display unit harness connector (B)
M203 terminal 15.
4. Check continuity between DVD player harness connector (A)
M272 terminal 20 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.67 – 14 : Continuity should exist.
SKIB4617E
67 – Ground: : Approx. 5 V
SKIB4618E
20 – 15 : Continuity should exist.
20 – Ground : Continuity should not exist.
SKIB4695E

TROUBLE DIAGNOSIS
AV-115
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2007 April2007 M35/M45
Warning Message of Whether Rear View Image Is Rolling or Not DisplayedNKS00495
1. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND FRONT DISPLAY UNIT
1. Disconnect AV (NAVI) control unit connector and front display unit connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminals 51, 52 and display unit harness con-
nector (B) M203 terminals 4, 6.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminals 51, 52 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK HORIZONTAL SYNCHRONIZING SIGNAL
1. Connect AV (NAVI) control unit connector and front display unit connector.
2. Turn ignition switch ON.
3. Check signal between AV (NAVI) control unit harness connector
M210 terminal 51 and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace front display unit.
3. CHECK VERTICAL SYNCHRONIZING SIGNAL
Check signal between AV (NAVI) control unit harness connector
M210 terminal 52 and ground.
OK or NG
OK >> Replace AV (NAVI) control unit.
NG >> Replace front display unit.
DVD Operation Screen Is Not DisplayedNKS00496
Refer to AV- 11 5 , "Warning Message of Whether Rear View Image Is Rolling or Not Displayed" .
It Cannot Be Switched to DVD ModeNKS00497
Refer to AV- 11 6 , "DVD SOUND IS NOT OUTPUT" . 51 – 4 : Continuity should exist.
52 – 6 : Continuity should exist.
51, 52 – Ground : Continuity should not exist.
SKIB4698E
51 – Ground:
SKIB4699E
SKIB3601E
52 – Ground:
SKIB4700E
SKIB3598E

AV-124
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
VOICE GUIDANCE
VOICE RECOGNITION
REAR VIEW MONITOR
The part of the route already
passed is deleted.A route is managed by sections between way-
points. If you passed the first waypoint, the section
between the starting point and the waypoint is
deleted. (It may not be deleted depending on the
area.)This is not a malfunction.
An indirect route is suggested.If there are restrictions (such as one way streets)
on roads close to the starting point or destination,
the system may suggest an indirect route.Adjust the location of the starting point or
destination.
The system may suggest an indirect route because
route calculation does not take into consideration
some areas such as narrow streets (gray roads).Reset the destination to a main or ordinary
road, and recalculate the route.
The landmark information does not
correspond to the actual informa-
tion.This may caused by insufficient or incorrect data on
the DVD-ROM.This is not a malfunction.
The suggested route does not
exactly connect to the starting
point, waypoints, or destination.There is no data for route calculation closer to
these locations.Set the starting point, waypoints and desti-
nation on main road, and perform route cal-
culation. Symptom Possible cause Possible solution
Symptom Possible cause Possible solution
The voice guidance is not avail-
able.Voice guidance is only available at certain intersec-
tions. In some cases, voice guidance is not avail-
able even when the vehicle should make a turn.This is not a malfunction.
The vehicle has deviated from the suggested
route.Go back to the suggested route or request
route calculation again.
Voice guidance is set to off. Turn on the voice guidance.
Route guidance is set to off. Turn on the voice guidance.
The guidance content does not
correspond to the actual condition.The content of the voice guidance may vary,
depending on the types of intersections at which
turns are made.Follow all traffic rules and regulations.
Symptom Possible cause Possible solution
The system does not recognize
the command.
The system recognizes the com-
mand incorrectly.The interior of the vehicle is too noisy.Close the windows or have other occu-
pants be quiet.
The volume of the voice is too low. Speak louder.
Pronunciation is unclear. Speak clearly.
Voice recognition mode is not yet ready to speak.Push the release “PTT” on the steering
switch, and speak a command after the
tone sounds.
5 seconds or more have passed after pushed and
released “PTT” on the steering switch.Make sure to speak a command within
5seconds after push and release “PTT” on
the steering switch.
Only a limited range of voice commands is usable
for each screen.Use a correct voice command appropriate
for the current screen.
Symptom Possible cause Possible solution
Rear view monitor image is not
displayedThe selector lever is not shifted in R position. Shift the selector lever in R position.