2007 INFINITI M35 lock

BL-260
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for Intelligent Key UnitNIS0020I
Termi-
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
1 SB Power source (fuse) Input — — Battery voltage
3YIPDM E/R current sig-
nalInputSTART At starter motor cranking 5
LOCK Any condition other than above 2
8WPush-button ignition
switch LOCK indicatorOutputLOCKPower supply position is in LOCK
position0
—Power supply position is in any
position other than LOCK1.2
9LPush-button ignition
switch ACC indicatorOutputACCPower supply position is in ACC
position0
—Power supply position is in any
position other than ACC1.2
10 VPush-button ignition
switch ON indicatorOutputONPower supply position is in ON
position0
—Power supply position is in any
position other than ON1.2
13 LG/B Key slot illumination Output LOCKDriver door is opened under the
condition that the Intelligent Key is
inserted into the key slot0 → Battery voltage → 0
Intelligent Key is removed from
key slot (when key slot illumination
is turned off)0
15 LGSteering lock unit
power sourceOutput LOCK — Battery voltage
16 P/BSteering lock unit sig-
nalInput/
OutputLOCK Steering lock: Lock Battery voltage
ACCSteering lock: Unlock
(Unlocked moment)0
19 BR/Y Key switch Input LOCKIntelligent Key is inserted into key
slotBattery voltage
Intelligent Key is removed from
key slot0
20 B Ground — — — 0
27 VA/T device (Detention
switch)InputLOCK A/T selector lever is in P position 0
ONA/T selector lever is in any posi-
tion other than PBattery voltage
28 SB Starter relay InputONA/T selector lever is in N or P posi-
tionBattery voltage
—Power supply position is in LOCK
position or A/T selector lever is in
any position other than N or P
position0
29 V/R Stop lamp switch Input —Brake pedal depressed Battery voltage
Brake pedal released 0
30 L/WIgnition power supply
(ACC)Input ACCPower supply position is in ACC
positionBattery voltage
31 GRIgnition power supply
(ON)Input ONPower supply position is in ON
positionBattery voltage

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-261
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
33 O PDU signal InputLOCK Steering lock: Lock 0
ACC Steering lock: Unlock 8
34 R PDU feed back signal Input LOCK At wake-up (Open driver door) 0
35 LG Vehicle speed signal Input ONAt speedometer operation (vehicle
speed approx. 40 km/h)
37 P CAN LInput/
Output—— —
38 L CAN HInput/
Output—— —
39 BR/WPush-button ignition
switchInput —Push-button ignition switch is
pressed0
Push-button ignition switch is
releasedBattery voltage
40 B Ground — — — 0
41 Y Power source (fuse) Input — — Battery voltage
42 P PDU wake up signal OutputLOCKAt sleep (30 seconds or more after
all doors are closed under the con-
dition that the power supply posi-
tion is in the LOCK position)Battery voltage
— At wake-up (Open driver door) 0
43 G Starter signal OutputON At starter motor cranking 0
— Other than above Battery voltage
46 V PDU signal Output— Steering lock: Lock Battery voltage
LOCK Steering lock: Unlocked moment 0
56 B Ground — — — 0
57 L Power source (fuse) Input — — Battery voltage
58 OA/T device (Detention
switch)InputLOCKAt sleep (30 seconds or more after
all doors are closed under the con-
dition that the power supply posi-
tion is in the LOCK position)0
— At wake-up (Open driver door) Battery voltage
63 P Stop lamp switch Input —Brake pedal depressed Battery voltage
Brake pedal released Battery voltage
64 L/RPush-button ignition
switch illuminationOutput —Push-button ignition switch illumi-
nation is turned on2.6
Push-button ignition switch illumi-
nation is turned off
(15 seconds or more after the
driver door is closed)0 Te r m i -
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
PKIA1935E

BL-262
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for Steering Lock UnitNIS0020J
69 OSteering lock unit con-
dition signal-1InputLOCK Steering lock: Lock 0
ACC
Steering lock: UnlockBattery voltage
ON Battery voltage
70 L/YSteering lock unit con-
dition signal-2InputLOCK Steering lock: Lock Battery voltage
ACC
Steering lock: Unlock0
ON 0
71 LG PDU signal OutputLOCK Steering lock: Lock Battery voltage
ACC Steering lock: Unlocked moment 0
72 B Ground — — — 0 Termi-
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
Termi-
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-but-
ton ignition
switch posi-
tionOperation or conditions
1 GR PDU signalInput/
OutputLOCKPress push-button ignition
switch with Intelligent Key
inside vehicle0 → Battery voltage → 0
(Battery voltage is detected when
pressing the push-button ignition
switch)
3 O Condition signal-1 InputLOCK Steering lock: Lock 0
ACC
Steering lock: UnlockBattery voltage
ON Battery voltage
4P/BIntelligent Key unit
signalInputLOCK Steering lock: Lock Battery voltage
ACC
Steering lock: Unlock0
ON 0
5 B Ground — — — 0
6 B Ground — — — 0
7 LG Power source Input — — Battery voltage
8 L/Y Condition signal-2 InputLOCK Steering lock: Lock Battery voltage
ACC
Steering lock: Unlock0
ON 0

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-263
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for BCMNIS0020K
Terminals and Reference Value for IPDM E/RNIS0020L
Termi-
nal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-but-
ton igni-
tion
switch
positionOperation or conditions
21 GRNATS antenna
amp.
(Built-in key slot)Input/
OutputLOCKIgnition switch is pressed
while inserting the Intelligent
Key into the key slotJust after pressing ignition switch.
Pointer of tester should move
23 W/V Security indicator Output LOCKIntelligent Key is removed
from key slot and power sup-
ply position is in LOCK posi-
tionBattery voltage → 0
(Every 2.4 seconds)
25 W/RNATS antenna
amp.
(Built-in key slot)Input/
OutputLOCKIgnition switch is pressed
while inserting the Intelligent
Key into the key slotJust after pressing ignition switch.
Pointer of tester should move
37 LGKey slot
(Key switch signal)Input LOCKIntelligent Key is removed
from key slot0
Intelligent Key is inserted into
key slotBattery voltage
38 WIgnition power sup-
ply (ON or START)Input ONPower supply position is in
ON positionBattery voltage
39 L CAN HInput/
Output—— —
40 P CAN LInput/
Output—— —
42 PPower source
(fuse)Input — — Battery voltage
52 B Ground — — — 0
55 WPower source
(Fusible link)Input — — Battery voltage
Te r m i -
nal No.Wire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-button
ignition switch
positionOperation or conditions
4W/RStarter motor power
supplyOutputLOCK — 0
START Starter motor is activating Battery voltage
49 L CAN HInput/
Output—— —
50 P CAN LInput/
Output—— —
53 GR/RA/T Shift position
signalInputON A/T shift position is P/ N position Battery voltage
LOCK Other than above 0

BL-264
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2007 April2007 M35/M45
Terminals and Reference Value for PDUNIS0020M
Te r -
minal
No.Wire
colorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Push-
button
ignition
switch
positionOperation or conditions
1 P Wake up signal InputLOCKSleep condition (30 seconds or
more after all doors are closed
under the condition that the power
supply position is in the LOCK posi-
tion)Battery voltage
—Wake-up condition (Open driver
door)0
2GStarter control sig-
nalInputON At starter motor cranking 0
— Any condition other than above Battery voltage
3GRSteering lock unit
power sourceOutputLOCKPush-button ignition switch is
pressed under the condition that
Intelligent Key is in the vehicle or
Intelligent Key is inserted0 → Battery voltage → 0
— Any condition other than above 0
6VSteering lock control
signal-1Input—Push-button ignition switch is
pressed under the condition that
Intelligent Key is in the vehicle or
Intelligent Key is insertedBattery voltage
LOCKPower supply position is in LOCK
position
(Steering lock activated)Battery voltage → 0 →
Battery voltage
(Battery voltage is detected
when activating the steer-
ing lock)
7LGSteering lock control
signal-2Input—Push-button ignition switch is
pressed under the condition that
Intelligent Key is in the vehicle or
Intelligent Key is insertedBattery voltage
LOCKPower supply position is in LOCK
position
(Steering lock activated)Battery voltage → 0 →
Battery voltage
(Battery voltage is detected
when activating the steer-
ing lock)
9OSteering lock feed
back signalInput—Power supply position is in ACC or
ON position0
LOCKPower supply position is in LOCK
position0 → 8 → 0
(0V is detected when acti-
vating the steering lock)
10 B Ground — — — 0
11 YIPDM E/R current
signalInputSTART At starter motor cranking 5
LOCK Any condition other than above 2
12 R Feed back signal InputLOCKSleep condition (30 seconds or
more after all doors are closed
under the condition that the power
supply position is in the LOCK posi-
tion)1
—Wake-up condition (any condition
other than above)0
13 R Starter relay OutputSTART At starter motor cranking Battery voltage
— Any condition other than above 4

BL-266
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2007 April2007 M35/M45
7. Select “NATS V.5.0”.
If “NATS V5.0” is not indicated, go to GI-39, "
CONSULT-II Data
Link Connector (DLC) Circuit" .
8. Perform each diagnostic test mode according to each service
procedure.
For further information, see the CONSULT-II Operation Manual
NATS-IVIS/NVIS.
CONSULT-II DIAGNOSTIC TEST MODE FUNCTION
NOTE:

When any initialization is performed, all ID previously registered will be erased and all NATS ignition keys
must be registered again.

The engine cannot be started with an unregistered key. In this case, the system will show “DIFFERENCE
OF KEY” or “LOCK MODE” as a self-diagnostic result on the CONSULT-II screen.
PIIB6275E
PIIB6276E
System Diagnosis mode DescriptionReference
page
NATS V5.0C/U INTIALIZATIONPerform registration again after repair, part replacement, and
additional key ID registration.
CAUTION:
“Control Unit Initialization” is activated only after per-
forming “Release steering lock”.Refer to the
Technical Bul-
letin.
SELF-DIAG RESULTS

Malfunctioning system stored in the ECM is displayed.

Printing the contents

Erasing the error recordBL-268
NATS BCM or S/ENTPIN READThe specified numbers of each control unit for acquisition of
password for control unit initialization are displayedRefer to the
Technical Bul-
letin.
STEERING LOCK
RELEASEIf the engine switch cannot be operated (the steering lock
cannot be released), release the steering lock forcibly and
make the engine switch operation possible.
CAUTION:
Always perform “Control Unit Initialization” and “Immo-
bilizer ID Registration” after performing “Release Steer-
ing Lock”.Refer to the
Technical Bul-
letin.
SELF-DIAG RESULTS

Malfunctioning system stored in the BCM is displayed.

Printing the contents

Erasing the error recordBL-268
NATS I-KEY SELF-DIAG RESULTS

Malfunctioning system stored in the Intelligent Key unit is
displayed.

Printing the contents

Erasing the error recordBL-269

BL-268
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: 2007 April2007 M35/M45
“NATS V5.0” SELF-DIAGNOSTIC RESULTS ITEM CHART
“NATS BCM OR S/ENT” SELF-DIAGNOSTIC RESULTS ITEM CHART
Suspect Systems Description Possible malfunction Action to take/Reference page
NO DTC NO DTC — —
DON'T ERASE BEFORE
CHECKING ENG DIAGThere is the engine trouble
diagnosis information in ECM
(ECM trouble diagnosis is nec-
essary separately)Engine control system malfunc-
tionThere is the engine trouble
diagnosis information in ECM.
Check the trouble diagnostic
results of “ENGINE” before
that.
LOCK MODE
[P1610]The immobilizer switches to the
mode that prevents the engine
from being started. If the ID ver-
ification between BCM and
ECM is NG, the ID verification
malfunction between remote
control starter and BCM may be
detected 5 times or more.—When “LOCK MODE” is dis-
played, check for any other dis-
played malfunction, and then
erase the self-diagnostic results
after replacement.
ID DISCORD, IMM-ECM
[P1611]The ID verification results
between BCM and ECM are
NG. The registration is neces-
sary.Registration of ECM is not com-
pletedBL-277
ECM malfunction Replace ECM.
CHAIN OF ECM-IMMU
[P1612]Inactive communication
between ECM and BCMOpen circuit in battery power
supply line of BCM
BL-275
Open circuit in ignition power
supply line of BCM
Open circuit in ground of BCM
Short circuit in communication
line between BCM and ECM to
power supply line
Open circuit in communication
line between BCM and ECM
Short circuit in communication
line between BCM and ECM to
ground
ECM malfunction
BCM malfunction
CHAIN OF IMMU-KEY
[P1614]BCM malfunction BCM malfunctionBCS-15
Suspect Systems Description Possible malfunction Action to take/Reference page
NO DTC NO DTC — —
ID DISCORD BCM-ECM
[B2192]The ID verification results
between BCM and ECM are
NG. The registration is neces-
sary.Registration of ECM is not com-
pletedPerform “Control Unit Initializa-
tion”, and then perform the ID
registration. Refer to the Tech-
nical Bulletin.
ECM malfunction Replace ECM.
CHAIN OF BCM-ECM
[B2193]Inactive communication
between ECM and BCMShort circuit in communication
line between BCM and ECM to
power supply lineMalfunction have occurred in
CAN communication
Check “Self-diagnostic Results”
of “Intelligent Key” using CON-
SULT-II. Refer to BL-150,
"SELF-DIAGNOSTIC
RESULTS" . Open circuit in communication
line between BCM and ECM
Short circuit in communication
line between BCM and ECM to
ground
ECM malfunction Replace ECM.

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-269
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
“NATS I-KEY” SELF-DIAGNOSTIC RESULTS ITEM CHART
Work FlowNIS0020O
1. LISTEN TO CUSTOMER COMPLAINT OR REQUEST
Get symptoms or listen to customer complaints or request.
NOTE:
In case of request for Intelligent Key or IVIS (NATS) system repair, the key ID re-registration might be neces-
sary. Keep all the Intelligent Keys before work for the re-registration.
Key ID registration request>>Register Intelligent Key by referring to CONSULT-II operation manual IVIS/
NVIS NATS.
Request for malfunction repair.>>GO TO 2.
2. CHECK DOOR LOCK AND REMOTE CONTROL FUNCTION
Check that Door Lock and remote control function of Intelligent Key operate normally.
Door Lock or remote control function is malfunctioning.>>Malfunction of Door Lock function, Refer toBL-77,
"WORK FLOW" .
Door Lock and remote control function are normal.>>GO TO 3.
DISCORD BCM-I-KEY
[B2194]The ID verification results
between BCM and Intelligent
Key unit are NG.Short circuit in communication
line between BCM and Intelli-
gent Key unit to power supply
lineMalfunction have occurred in
CAN communication
Check “Self-diagnostic Results”
of “Intelligent Key” using CON-
SULT-II. Refer to BL-150,
"SELF-DIAGNOSTIC
RESULTS" . Short circuit in communication
line between BCM and ECM to
ground
Intelligent Key unit malfunctionBL-123
ANTI-SCANNING
[B2195]A remote control starter that is
not Genuine NISSAN is
installedIf a remote control starter that is
not Genuine NISSAN is
installed, the anti-theft system
is activated and the engine may
not be started. In this case,
remove the parts after the cus-
tomer understands the situa-
tion.— Suspect Systems Description Possible malfunction Action to take/Reference page
Suspect Systems Description Possible malfunction Action to take/Reference page
NO DTC NO DTC — —
DISCORD BCM-I-KEY
[B2590]The ID verification results
between Intelligent Key unit
and BCM are NG.Short circuit in communication
line between BCM and Intelli-
gent Key unit to power supply
lineMalfunction have occurred in
CAN communication
Check “Self-diagnostic Results”
of “Intelligent Key” using CON-
SULT-II. Refer to BL-150,
"SELF-DIAGNOSTIC
RESULTS" . Short circuit in communication
line between BCM and ECM to
ground
BCM malfunctionBCS-15