2007 INFINITI M35 seat memory

SE-2Revision: 2007 April2007 M35/M45 Check Reclining Switch Circuit ............................... 71
Check Lifting Switch (Front) Circuit ........................ 73
Check Lifting Switch (Rear) Circuit ......................... 75
Check Power Seat Switch Ground Circuit .............. 76
Check Telescopic Switch Circuit ............................. 77
Check Tilt Switch Circuit ......................................... 79
Check Seat Memory and Set Switch Circuit ........... 81
Check Seat Memory Indicator Lamp Circuit ........... 82
Check Door Mirror Sensor Power Supply and
Ground Circuit ........................................................ 84
Check A/T Device (Detention Switch) Circuit ......... 86
Check Front Door Switch (Driver Side) Circuit ....... 87
Check UART Communication Line Circuit .............. 88
Check Lumbar Support Circuit ............................... 90
POWER SEAT(PASSENGER SIDE) ......................... 92
Schematic ............................................................... 92
Wiring Diagram — SEAT — .................................... 93
POWER SEAT(REAR) .............................................. 96
Component Parts and Harness Connector Location ... 96
System Description ................................................. 96
REAR POWER SEAT LH AND RH OPERATION ... 96
REAR SEAT RETREAT FUNCTION ................... 97
Schematic ............................................................... 98
Wiring Diagram — R/SEAT — ................................ 99
Terminals and Reference Values for Rear Seat Con-
trol Unit .................................................................103
Work Flow .............................................................104
Trouble Diagnoses Symptom Chart ......................104
Check Rear Power Seat Power Supply Circuit .....104
Check Rear Seat Control Unit Power Supply and
Ground Circuit ......................................................105
Check Rear Seat Sliding Motor Circuit .................106
Check Rear Power Seat Switch Circuit ................107
Check Automatic Return Cancel Switch Circuit ....109
Check Automatic Return Cancel Switch ...............110
Check Rear Door Switch Circuit ............................111
Check Rear Seat Sliding Sensor Circuit ...............112
CLIMATE CONTROLLED SEAT .............................114
Component Parts and Harness Connector Location .114
System Description ...............................................114
Schematic .............................................................118
Wiring Diagram — C/SEAT — ..............................119
Terminal and Reference Value for Climate Con-
trolled Seat Control Unit .......................................124
Work Flow .............................................................125
Trouble Diagnoses Symptom Chart ......................126
Preliminary Check ................................................126
Check Climate Controlled Seat Control Unit Power
Supply Circuit .......................................................127
Check Climate Controlled Seat Control Unit Power
Supply and Ground Circuit ...................................128
Check Climate Controlled Seat Switch Power Sup-ply Circuit ..............................................................131
Check Climate Controlled Seat Switch Circuit ......132
Check Climate Controlled Seat Switch Indicator Cir-
cuit ........................................................................134
Check Seat Cushion Thermal Electric Device Cir-
cuit ........................................................................136
Check Seatback Thermal Electric Device Circuit ..137
Check Seat Cushion Thermal Electric Device Sen-
sor Circuit ..............................................................138
Check Seatback Thermal Electric Device Sensor
Circuit ....................................................................140
Check Climate Controlled Seat Blower Motor Circuit .141
Check Climate Controlled Seat Control Unit .........143
HEATED SEAT ........................................................144
Component Parts and Harness Connector Location .144
System Description ...............................................144
Schematic .............................................................146
Wiring Diagram — HSEAT — ...............................147
Terminals and Reference Values for Rear Seat Con-
trol Unit ..................................................................152
Work Flow .............................................................152
Trouble Diagnoses Symptom Chart ......................152
Check Rear Heated Seat Power Supply and Ground
Circuit ....................................................................153
Check Rear Seat Control Unit Power Supply and
Ground Circuit .......................................................154
Check Rear Heated Seat Switch Circuit ...............156
Check Rear Heated Seat Indicator Power Supply
Circuit ....................................................................158
Check Rear Heated Seat Indicator Circuit ............159
Check Rear Heated Seat Circuit ...........................161
Check Rear Seatback Heater Circuit ....................162
FRONT SEAT ..........................................................164
Driver's Seat Components ....................................164
Passenger's Seat Components .............................166
Removal and Installation .......................................168
REMOVAL ..........................................................168
INSTALLATION ..................................................168
Disassembly and Assembly ..................................169
SEATBACK ........................................................169
SEAT CUSHION ................................................170
CLIMATE CONTROLLED SEAT ........................172
REAR SEAT .............................................................173
Bench Seat Components ......................................173
Power Seat (Split Type) Components ...................175
Removal and Installation .......................................177
BENCH SEAT ....................................................177
POWER SEAT ...................................................177
Disassembly and Assembly ..................................178
BENCH SEAT ....................................................178
POWER SEAT ...................................................180

AUTOMATIC DRIVE POSITIONER
SE-11
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
AUTOMATIC DRIVE POSITIONERPFP:28491
Component Parts And Harness Connector LocationNIS0025Q
PIIB6292E
1. Fuse block (J/B) 2. Fuse and fusible link box 3. BCM M1, M2, M3
(View with the glove box assembly
removed)
4. A. Automatic drive positioner control
unit M6, M7
B. Telescopic motor M45
C. Telescopic sensor M44
D. Tilt sensor M37
E. Tilt motor M36
(View with the driver lower panel
removed)5. A. Front lifting motor B209
B. Rear lifting motor B210
C. Driver seat control unit
B204,B205
D. Sliding motor B2076. Seat memory switch D9
7. A. Lumbar support switch B212
B. Reclining switch B213
C. Sliding/Lifting switch B2138. A. ADP steering switch M46
B. Key slot M14
C. Door mirror control switch M959. Reclining motor B208

SE-12
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
System DescriptionNIS0025R

The system automatically moves the driver seat, steering and door mirror position by the driver seat con-
trol unit and the automatic drive positioner control unit. The driver seat control unit corresponds with the
automatic drive positioner control unit via UART communication. The driver seat control unit can store the
optimum driving positions (driver seat, steering and door mirror position) for 2 people. If the driver
changes, one-touch operation allows changing to the other driving position.

The driver seat, steering and door mirror position are adjusted automatically to the proper positions for the
driver in different ways: MEMORY OPERATION, EXITING OPERATION, ENTRY OPERATION and
INTELLIGENT KEY INTERLOCK OPERATION.
MANUAL OPERATION
The driving position (seat, steering and door mirror position) can be adjusted with the power seat switch, ADP
steering switch and door mirror control switch.
NOTE:
The door mirrors can be manually operated with the ignition switch in either ACC or ON.
MEMORY OPERATION
The driver seat control unit can store the optimum driving positions (seat, steering and door mirror position) for
2 people. If the front seat position is changed, one-touch (pressing desired memory switch for more than 0.5
second) operation allows changing to the other driving position.
Operation procedure
1. Turn ignition switch ON.
2. Press desired memory switch for 0.5 second. (Indicator LED illuminates.)
3. Driver seat, steering and door mirror will move to the memorized position.
(Indicator LED blinks during adjustment, then illuminates for 5 seconds.)
Operation Condition
If the following conditions are not satisfied, memory switch operation is not performed.

Ignition switch is in ON position.

Driver side power seat switch, ADP steering switch and door mirror control switch are not operated.

Seat memory switch and set switch are not operated.

Output malfunction is not detected.

CAN and UART communications are normal.

A/T selector lever position is in P position.

Detention switch malfunction is not detected.
[Detention switch malfunction is sensed when detention switch remains OFF, vehicle speed is higher than
7 km/H. (4 MPH).]

Input voltage from tilt sensor and telescopic sensor are normal.
NOTE:
The memory operation operates following order.
Function Description
Manual operationThe driving position (seat, steering and door mirror position) can be adjusted with
the power seat switch ADP steering switch or door mirror control switch.
Auto-
matic
operationMemory operation The seat, steering and door mirror move to the stored driving position by pushing
seat memory switch (1 or 2).
Entry/
Exiting
functionExiting operation At exit, the seat moves backward and the steering wheel moves upward.
Entry operationAt entry, the seat and steering wheel returns from exiting position to the previous
driving position before the exiting operation.
Intelligent Key interlock operationPerform memory operation, exiting operation and entry operation by pressing Intel-
ligent Key unlock button.

AUTOMATIC DRIVE POSITIONER
SE-13
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
*: Door mirror operation starts with the start of seat sliding operation.
Storing Memory Procedure
1. Turn ignition switch to ON.
2. Shift A/T selector lever to P position.
3. Adjust position of driver seat, steering and mirror position.
4. Press set switch.

Indicator LED for which driver seat positions are already retained in memory is illuminated for 5 sec-
onds.

Indicator LED for which driver seat positions are not retained in memory is illuminated for 0.5 second.
5. Press memory switch for which driver seat positions are to be entered in memory for more than 0.5 sec-
ond within 5 seconds after pressing the set switch (during the indicator LED is illuminated).

To enter driver seat positions in blank memory, indicator LED will be illuminated for 5 seconds.

To modify driver seat positions, indicator LED will be turned OFF for 0.5 second then illuminated for 5
seconds.
6.

If you need setting of INTELLIGENT KEY INTERLOCK OPERATION, continue this procedure.

If you don't need setting of INTELLIGENT KEY INTERLOCK OPERATION, the procedure is finished.
Conform the operations of each part with the MEMORY OPERATION.
7. Press intelligent key unlock button within 5 seconds after pressing memory switch.
(While memory switch LED is illuminated.)
8. Conform the operations of each part with MEMORY OPERATION and INTELLIGENT KEY INTERLOCK
OPERATION.
NOTE:

Driving position is erased from the memory when battery cable is disconnected.
Order of priority Operated portion
1* Seat sliding
2 Steering telescopic
3 Steering wheel tilt
4 Seat reclining
5 Seat lifter (front)
6 Seat lifter (rear)

SE-14
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
EXITING OPERATION
When exiting, when the condition is satisfied, the seat is moved backward 40 mm (1.57 in) from normal sitting
position and the steering is moved to the most upper position and front position.
The seat slide amount and the steering operation at entry/exit operation can be changed by set switch, CON-
SULT-II and display (located in the instrument panel). Refer to SE-16, "
SETTING CHANGE FUNCTION" .
Operation Condition

Ignition switch: OFF / Driver side door switch: ON (OPEN)
If the following conditions are not satisfied, exiting operation is not performed.

Ignition switch is in OFF position.

A/T selector lever position is in P position.

Vehicle speed is less than 7 km/h. (4 MPH).

Driver side power seat switch and ADP steering switch are not operated.

Seat memory switch and set switch is not operated.

Door mirror control switch is not operated at change over switch is in LH or RH position.

Output malfunction is not detected.

Detention switch malfunction is not detected.
[Detention switch malfunction is sensed when detention switch remains OFF and vehicle speed is higher
than 7 km/h. (4 MPH).]

CAN communications are normal.

Initialization has been done. Refer to SE-16, "INITIALIZATION PROCEDURE" .
ENTRY OPERATION
When the seat is in the exiting position when either condition (1 or 2) is satisfied, the seat returns from exiting
position to the previous driving position.
Operation Condition
1. Ignition switch: ON
2. Ignition switch: ACC / Driver side door switch: OFF (CLOSE)
If the following conditions are not satisfied, entry operation is not performed.

Ignition switch is in OFF position.

A/T selector lever position is in P position.

Vehicle speed is less than 7 km/h (4 MPH).

Driver side power seat switch, ADP steering switch and door mirror control switch are not operated.

Seat memory switch and set switch is not operated.

Output malfunction is not detected.

Detention switch malfunction is not detected.
[Detention switch malfunction is sensed when detention switch remains OFF and vehicle speed is higher
than 7 km/h (4 MPH).]

CAN communications are normal.

Exiting positions have not been changed during and after exiting operation.

AUTOMATIC DRIVE POSITIONER
SE-15
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
INTELLIGENT KEY INTERLOCK OPERATION
When pressing unlock button on Intelligent Key or request switch, the system performs memory operation,
exiting operation and entry operation.
Operation procedure
1. Press unlock button on Intelligent Key or request switch.
2. The system performs MEMORY OPERATION, and then performs EXITING OPERATION continually.
NOTE:
If the seat position is in memorized position before push unlock button, MEMORY OPEPATION dose not per-
form.
3. Turn ignition switch ON or close driver side door when ignition switch is in “ACC” position.
4. The system performs ENTRY OPERATION. (Seat and steering positions are moved to memorized posi-
tions. The memorize position is related to key ID.)
Operation Condition
If the following conditions are not satisfied, memory switch operation is not performed.

Ignition switch is in OFF position.

Driver side power seat switch and door mirror control switch are not operated.

Seat memory switch and set switch are not operated.

Output malfunction is not detected.

CAN and UART communications are normal.

A/T selector lever position is in P position.

Detention position switch malfunction is not detected.
[Detention position switch malfunction is sensed when detention switch remains OFF and vehicle speed is
higher than 7 km/h (4 MPH).]
Linking Intelligent Key to the Stored Memory Procedure
NOTE:

If ignition switch turns ON in the middle of memory operation, the system does not perform exiting opera-
tion after memory operation.

If ignition switch turns ON in the middle of exiting operation, entry operation starts at that time.

If entry / exiting operation is cancelled, perform memory operation only.
FAIL-SAFE MODE
If any of the parts move more than a period “T” without any switch operation, MEMORY OPERATION, EXIT-
ING OPERATION, ENTRY OPERATION, INTELLIGENT KEY INTERLOCK OPERATION and the malfunction
part of manual operations are not operated (output malfunction).
Canceling Fail-safe Mode
The mode is cancelled by either of the following operations.

When the selector lever is shifted to P position from any other position (detention switch is turned OFF).
Operated portion T
Seat slidingApprox. 0.1 sec.
Seat recliningApprox. 0.1 sec.
Seat lifter (front)Approx. 0.1 sec.
Seat lifter (rear)Approx. 0.1 sec.
Steering tiltApprox. 0.1 sec.

AUTOMATIC DRIVE POSITIONER
SE-37
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
CONSULT-II Function (AUTO DRIVE POS.)NIS00260
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
SELF-DIAGNOSIS RESULTS
HOW TO READ SELF-DIAG RESULTS
NOTE:

CAN communication malfunction and detention switch malfunction are displayed on “TIME”. (1)
–If error is detected in the present, “CRNT” is displayed.
–If error is detected in the past (present error is not detected), “PAST” is displayed.
–If error has never been detected, nothing is displayed on “TIME”.

Any items other than CAN communication malfunction and detention switch malfunction are counted. (2)
–If error is detected, error detection frequency is displayed from “1” to “127” on “TIME”.
–If error has never been detected, nothing is displayed on “TIME”.
–Can clear the detected memory.
Normal: Clear memory in normal condition, history is erased and nothing is displayed on “TIME”.
Error: Clear memory in error condition, error is detected again and “1” is displayed on “TIME”.
AUTO DRIVE POS.
diagnostic modeDescriptionReference
page
WORK SUPPORT Changes settings for each function.SE-16
SELF-DIAG RESULTS Displays driver seat control unit self-diagnosis results.SE-37
DATA MONITOR Displays driver seat control unit input/output data in real time.SE-38
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.LAN-44
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.SE-39
ECU PART NUMBER Driver seat control unit part number can be read. —
PIIB6449E

SE-38
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
DISPLAY ITEM LIST
DATA MONITOR
SELECTIOM FROM MEMU
DTCSelf-diagnosis item
(CONSULT-II indication)DTC detection conditionReference
page
U1000 CAN COMM CIRCUITWhen driver seat control unit is not transmitting or receiving CAN communication
signal for 2 seconds or more.SE-42

B2112 SEAT SLIDEWhen any manual and automatic operations are not performed, if any motor
operations of seat slide is detected for 0.1 second or more, status is judged “Out-
put error”.SE-45
SE-53
B2113 SEAT RECLININGWhen any manual and automatic operations are not performed, if any motor
operations of seat reclining is detected for 0.1 second or more, status is judged
“Output error”.SE-46SE-55
B2114 SEAT LIFTER-FRWhen any manual and automatic operations are not performed, if any motor
operations of seat lifting FR is detected for 0.1 second or more, status is judged
“Output error”.SE-47SE-57
B2115 SEAT LIFTER-RRWhen any manual and automatic operations are not performed, if any motor
operations of seat lifting RR is detected for 0.1 second or more, status is judged
“Output error”.SE-49SE-59
B2116 STEERING TILTWhen any manual and automatic operations are not performed, if any motor
operations of steering tilt is detected for 0.1 second or more, status is judged
“Output error”.SE-51
B2118 STRG TILT SENSORWhen driver seat control unit detects 0.1V or lower, or 4.9V or higher, from tilt
sensor for 0.5 seconds or more.SE-63
B2119 STEERING TELESCOWhen driver seat control unit detects 0.1V or lower, or 4.9V or higher, from
telescopic sensor for 0.5 seconds or more.SE-61
B2126 DETENT SWWith the A/T selector lever in P position (Detente switch OFF), if the vehicle
speed of 7 km/h (4 MPH) or higher was input the detention switch input system is
judged malfunctioning.SE-86
B2128 UART COMM Malfunction is detected in UART communication.SE-88
Monitor item [OPERATION or UNIT] Contents
SET SW “ON/OFF” ON/OFF status judged from the setting switch signal is displayed.
MEMORY SW1 “ON/OFF” ON/OFF status judged from the seat memory switch 1 signal is displayed.
MEMORY SW2 “ON/OFF” ON/OFF status judged from the seat memory switch 2 signal is displayed.
SLIDE SW–FR “ON/OFF” ON/OFF status judged from the sliding switch (FR) signal is displayed.
SLIDE SW–RR “ON/OFF” ON/OFF status judged from the sliding switch (RR) signal is displayed.
RECLN SW–FR “ON/OFF” ON/OFF status judged from the reclining switch (FR) signal is displayed.
RECLN SW–RR “ON/OFF” ON/OFF status judged from the reclining switch (RR) signal is displayed.
LIFT FR SW–UP “ON/OFF” ON/OFF status judged from the FR lifting switch (UP) signal is displayed.
LIFT FR SW–DN “ON/OFF” ON/OFF status judged from the FR lifting switch (DOWN) signal is displayed.
LIFT RR SW–UP “ON/OFF” ON/OFF status judged from the RR lifting switch (UP) signal is displayed.
LIFT RR SW–DN “ON/OFF” ON/OFF status judged from the RR lifting switch (DOWN) signal is displayed.
MIR CON SW–UP “ON/OFF”ON/OFF status judged from the door mirror remote control switch (UP) signal is
displayed.
MIR CON SW–DN “ON/OFF”ON/OFF status judged from the door mirror remote control switch (DOWN) signal
is displayed.
MIR CON SW–RH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (RIGHT) signal
is displayed.
MIR CON SW–LH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (LEFT) signal is
displayed.
MIR CHNG SW–R “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
RIGHT) signal is displayed.