2007 INFINITI M35 sensor

GI-54
TERMINOLOGY
Revision: 2007 April2007 M35/M45
Nonvolatile random access memory NVRAM ***
On board diagnostic system OBD system Self-diagnosis
Open loop OL Open loop
Oxidation catalyst OC Catalyst
Oxidation catalytic converter system OC system ***
Oxygen sensor O2S Exhaust gas sensor
Park position switch *** Park switch
Park/neutral position switch PNP switchPark/neutral switch
Inhibitor switch
Neutral position switch
Periodic trap oxidizer system PTOX system ***
Positive crankcase ventilation PCV Positive crankcase ventilation
Positive crankcase ventilation valve PCV valve PCV valve
Powertrain control module PCM ***
Programmable read only memory PROM ***
Pulsed secondary air injection control sole-
noid valvePAIRC solenoid valve AIV control solenoid valve
Pulsed secondary air injection system PAIR system Air induction valve (AIV) control
Pulsed secondary air injection valve PAIR valve Air induction valve
Random access memory RAM ***
Read only memory ROM ***
Scan tool ST ***
Secondary air injection pump AIR pump ***
Secondary air injection system AIR system ***
Sequential multiport fuel injection system SFI system Sequential fuel injection
Service reminder indicator SRI ***
Simultaneous multiport fuel injection sys-
tem*** Simultaneous fuel injection
Smoke puff limiter system SPL system ***
Supercharger SC ***
Supercharger bypass SCB ***
System readiness test SRT ***
Thermal vacuum valve TVV Thermal vacuum valve
Three way catalyst TWC Catalyst
Three way catalytic converter system TWC system ***
Three way + oxidation catalyst TWC + OC Catalyst
Three way + oxidation catalytic converter
systemTWC + OC system ***
Throttle body TBThrottle chamber
SPI body
Throttle body fuel injection system TBI system Fuel injection control
Throttle position TP Throttle position
Throttle position sensor TPS Throttle sensor
Throttle position switch TP switch Throttle switch
Torque converter clutch solenoid valve TCC solenoid valveLock-up cancel solenoid
Lock-up solenoid NEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM

TERMINOLOGY
GI-55
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: 2007 April2007 M35/M45
***: Not applicableTransmission control module TCM A/T control unit
Turbocharger TC Turbocharger
Vehicle speed sensor VSS Vehicle speed sensor
Volume air flow sensor VAFS Air flow meter
Warm up oxidation catalyst WU-OC Catalyst
Warm up oxidation catalytic converter sys-
temWU-OC system ***
Warm up three way catalyst WU-TWC Catalyst
Warm up three way catalytic converter sys-
temWU-TWC system ***
Wide open throttle position switch WOTP switch Full switchNEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM

GW-2Revision: 2007 April2007 M35/M45 SIDE WINDOW GLASS ............................................ 57
Removal and Installation ........................................ 57
REMOVAL ........................................................... 57
INSTALLATION .................................................... 58
REAR WINDOW GLASS AND MOLDING ................ 59
Removal and Installation ........................................ 59
REMOVAL ........................................................... 59
INSTALLATION .................................................... 60
FRONT DOOR GLASS AND REGULATOR ............. 61
Removal and Installation ........................................ 61
DOOR GLASS ..................................................... 61
REGULATOR ASSEMBLY .................................. 62
Disassembly and Assembly .................................... 63
REGULATOR ASSEMBLY .................................. 63
Inspection after Installation ..................................... 63
SYSTEM INITIALIZATION ................................... 63
INSPECT THE FUNCTION OF THE ANTI-
PINCH SYSTEM. ................................................. 63
FITTING INSPECTION ........................................ 64
REAR DOOR GLASS AND REGULATOR ............... 65
Removal and Installation ........................................ 65
DOOR GLASS ..................................................... 65
REGULATOR ASSEMBLY .................................. 66
Disassembly and Assembly .................................... 68
REGULATOR ASSEMBLY .................................. 68
Inspection after Installation ..................................... 68
SYSTEM INITIALIZATION ................................... 68
INSPECT THE FUNCTION OF THE ANTI-
PINCH SYSTEM .................................................. 68
FITTING INSPECTION ........................................ 68
INSIDE MIRROR ....................................................... 69
Wiring Diagram –I/MIRR– ....................................... 69
Removal and Installation ........................................ 70
REMOVAL ........................................................... 70
INSTALLATION .................................................... 70
REAR WINDOW DEFOGGER .................................. 71
Component Parts and Harness Connector Location ... 71
System Description ................................................. 71
CAN Communication System Description .............. 73
CAN Communication Unit ....................................... 73
Schematic ............................................................... 74
Wiring Diagram — DEF — ..................................... 75
Terminal and Reference Value for BCM ................. 80
Terminal and Reference Value for IPDM E/R ......... 80
CONSULT-II Function (BCM) .................................. 81
CONSULT-II START PROCEDURE .................... 81
DATA MONITOR .................................................. 81
ACTIVE TEST ..................................................... 81
CONSULT-II Function (IPDM E/R) .......................... 81
CONSULT-II START PROCEDURE .................... 81
DATA MONITOR .................................................. 81ACTIVE TEST ...................................................... 81
Work Flow ............................................................... 82
Trouble Diagnoses Symptom Chart ........................ 82
Check BCM Power Supply and Ground Circuit ...... 83
Check Rear Window Defogger Switch Circuit ......... 84
Check Rear Window Defogger Power Supply Cir-
cuit .......................................................................... 84
Check Rear Window Defogger Circuit .................... 86
Check Door Mirror Defogger Power Supply Circuit ... 87
Check Driver Side Door Mirror Defogger Circuit ..... 89
Check Passenger Side Door Mirror Defogger Circuit
... 90
Check Filament ....................................................... 92
Filament Repair ....................................................... 92
REPAIR EQUIPMENT ......................................... 92
REPAIRING PROCEDURE ................................. 93
REVERSE INTERLOCK DOOR MIRROR SYSTEM ... 94
Component Parts and Harness Connector Location ... 94
System Description ................................................. 94
OPERATION CONDITIONS ................................ 94
MIRROR UNGLE MEMORY FUNCTION ............ 94
REVERSE INTERLOCK DOOR MIRROR SYS-
TEM OPERATION ............................................... 95
CAN Communication System Description .............. 95
CAN Communication Unit ....................................... 95
Schematic ............................................................... 96
Wiring Diagram — MIRROR — .............................. 97
Terminals and Reference Values for Automatic
Drive Positioner Control Unit .................................103
Terminals and Reference Values for Driver Seat
Control Unit ...........................................................104
CONSULT-II Function (AUTO DRIVE POS.) ........105
CONSULT-II START PROCEDURE ...................105
DATA MONITOR ................................................105
ACTIVE TEST ....................................................105
Work Flow .............................................................106
Symptom Chart .....................................................106
Check Changeover Switch Circuit ........................107
Check Mirror Switch Circuit ...................................109
Check Mirror Motor Circuit .................................... 111
Check Mirror Sensor Circuit ..................................114
Check A/T Control Device R Position Circuit ........117
DOOR MIRROR .......................................................118
Automatic Drive Positioner Interlocking Door Mirror .118
Removal and Installation .......................................118
REMOVAL ..........................................................118
INSTALLATION ..................................................118
Disassembly and Assembly ..................................119
DISASSEMBLY ..................................................119
ASSEMBLY ........................................................120

POWER WINDOW SYSTEM
GW-19
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
FAIL-SAFE CONTROL
The encoder signal detects the up / down speed / detection of door glass. If the malfunction is detected to the
encoder signal or the difference between the glass fully closed position (memorized in power window main
switch or power window sub-switch) and the actual glass position is detected, it shifts into the fail-safe control
It is shifts into the fail-safe control, the initialization is not performed and the following function is not activated

Auto up operation

Anti-pinch function
It is shifts into the fail-safe control, performed the initialization to resume normal operation condition.
POWER WINDOW CONTROL BY THE KEY CYLINDER SWITCH
When ignition key switch is OFF, front power window can be opened or closed by turning the key cylinder
switch UNLOCK / LOCK position more than 1.5 second over condition.

Power window can be opened as the door key cylinder is kept fully turning to the UNLOCK position.

Power window can be closed as the door key cylinder is kept fully turning to the LOCK position.
The power window DOWN stops when the following operations are carried out.

While performing open / close the window, power window is stopped at the position as the door key cylin-
der is placed on NEUTRAL.

When the ignition switch is turned ON while the power window DOWN is operated.
CAN Communication System DescriptionNIS0021H
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNIS0021I
Refer to LAN-50, "CAN System Specification Chart"
DTC Condition
Pulse sensor detects malfunctionDuring the glass opening/closing operation, a pulse signal is continuously
detected for the specified terms or more
Both pulse sensors detect malfunctionDuring the glass opening/closing operation, both pulse signals are not
detected for the specified values or more
Pulse direction malfunctionThe following condition is detected for the specified values or more. The
pulse signal (detected during glass open/close operation) detects the
opposite direction to the driving direction of power window motor.
Glass recognized position malfunction 1During the glass opening/closing operation, the difference between the
glass fully closed position (memorized in power window main switch or
power window sub-switch) and the actual glass position is detected for
the specified values or more.
Glass recognized position malfunction 2During the glass opening/closing operation, a pulse count is detected that
is above the glass full stroke
Glass fully closed position not updated malfunctionContinuously perform the glass open/close operation (with the glass not
fully closed) at the specified value (approx. 10 time) or more

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-95
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45

through 10A fuse [No.21, located in the fuse block (J/B)]

to automatic drive positioner control unit terminal 34 and

to driver seat control unit terminal 40.
Ground is supplied

to automatic drive positioner control unit terminals 40 and 48.

through body grounds M16 and M70.

to driver seat control unit terminals 32 and 48.

through body grounds B5, B40 and B131.

to door mirror remote control switch terminal 13

through body grounds M16 and M70.
REVERSE INTERLOCK DOOR MIRROR SYSTEM OPERATION

When the ignition switch is in ON position, A/T control device into R position. Then TCM (in A/T assembly)
detects it and sends the A/T shift position signal to the driver seat control unit via DATA LINE (CAN H,
CAN L).

When selecting either left and right changeover switch, the automatic drive position control unit judges
which door mirror is selected according to the voltage of terminals 2 and 18. And then, it sends the signal
to driver seat control unit via communication signal.

When the driver seat control unit receives the A/T shift position signal and changeover switch signal, it
sends the operation signal to the automatic drive positioner control unit using the communication signal so
that the each mirror sensor voltage stays in a specified value.

Door mirror (RH) selected
Supply the power from terminals 14, 15 and 30 to door mirror (RH) terminals 5, 6 and 7 so that the voltage
of terminals 5 and 21 stays in a specified value. Then, adjust the mirror angle.

Door mirror (LH) selected
Supply the power from terminals 16, 31 and 32 to door mirror (LH) terminals 5, 6 and 7 do that the voltage
of terminals 6 and 22 is the specified value. Then, adjust the mirror angle.
CAN Communication System DescriptionNIS00232
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNIS00233
Refer to LAN-50, "CAN System Specification Chart"

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-103
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Automatic Drive Positioner Control UnitNIS00236
Te r -
minalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
2VChangeover switch
RH signalInputWhen changeover
switch positionRH 0
Other than above 5
3GMirror switch
UP signalInputWhen mirror switch
positionUP 0
Other than above 5
4WMirror switch
LEFT signalInputWhen mirror switch
positionLEFT 0
Other than above 5
5L/RDoor mirror RH sensor
vertical signalInputWhen door mirror
RH mirror face posi-
tionClose to perk 4.2
Close to valley 0.5
6LGDoor mirror LH sensor
vertical signalInputWhen door mirror LH
mirror face positionClose to perk 4.2
Close to valley 0.5
10 O UART LINE (TX)Input/
OutputTilt switch operated
14 LDoor mirror RH mirror
motor
UP signalOutputWhen door mirror
RH mirror motor
operationUP Battery voltage
Other than above 0
15 GDoor mirror RH mirror
motor LEFT signalOutputWhen door mirror
RH mirror motor
operationLEFT Battery voltage
Other than above 0
16 W/LDoor mirror LH mirror
motor RIGHT or DOWN
signalOutputWhen door mirror LH
mirror motor opera-
tionRIGHT or DOWN Battery voltage
Other than above 0
18 OChangeover switch
LH signalInputWhen changeover
switch positionLH 0
Other than above 5
19 L Mirror switch DOWN signal InputWhen mirror switch
positionDOWN 0
Other than above 5
20 BR Mirror switch RIGHT signal inputWhen mirror switch
positionRIGHT 0
Other than above 5
21 SBDoor mirror RH sensor
horizontal signalInputWhen door mirror
RH mirror face posi-
tionClose to left edge 3.5
Close to right edge 0.5
22 O/LDoor mirror LH sensor
horizontal signalInputWhen door mirror LH
mirror face positionClose to left edge 0.5
Close to right edge 3.5
26 P UART LINE (RX)Input/
OutputTilt switch operated
30 GRDoor mirror LH mirror
motor RIGHT or DOWN
signalOutputWhen door mirror LH
mirror motor opera-
tionRIGHT or DOWN Battery voltage
Other than above 0
SKIA0175E
SKIA0175E

GW-104
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Driver Seat Control UnitNIS00237
31 BRDoor mirror LH mirror
motor UP signalOutputWhen door mirror LH
mirror motor opera-
tionUP Battery voltage
Other than above 0
32 VDoor mirror LH mirror
motor LEFT signalOutputWhen door mirror LH
mirror motor opera-
tionLEFT Battery voltage
Other than above 0
33 W Mirror sensor power supply Output — Battery voltage
34 R Power supply (fuse) Input — Battery voltage
39 L Power supply (fusible link) Input — Battery voltage
40 B Ground (signal) — — 0
41 Y Sensor ground — — 0
48 B Ground (power) — — 0 Te r -
minalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
Te r m i -
nal Wire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
1 R/G UART LINE (RX)Input/
OutputTilt switch operated
3 L CAN-HInput/
Output——
17 W/R UART LINE (TX)Input/
OutputTilt switch operated
19 P CAN-LInput/
Output——
32 B/W Ground (signal) — — 0
33 W Power supply (fusible link) Input — Battery voltage
40 B/W Power supply (fuse) Input — Battery voltage
48 B/W Ground (power) — — 0
SKIA0175E
SKIA0175E

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-105
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
CONSULT-II Function (AUTO DRIVE POS.)NIS00238
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
*1: For setting automatic drive positioner functions only.
*2: During vehicle driving, do not perform active test.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure"
DATA MONITOR
Selection from Menu
ACTIVE TEST
CAUTION:
During vehicle driving, do not perform active test.
NOTE:
If active test is performed, reset seat memory and key fob interlock drive positioner after performing work.
CONSULT-II
diagnosis
itemsInspection item, self-diagnosis mode Content Refer to page
AUTO DRIVE
POSITIONERWORK SUPPORT*
1Changes the setting for each function.SE-39
SELF–DIG RESULTS Check the self-diagnosis results.SE-37
DATA MONITOR Selection from menuDisplays the input data to driver seat control
unit and automatic driving positioned control
unit on real-time basis.SE-38
CAN DIAGNOSTIC SUPPORT MONITORThe results of transmit / receive diagnosis of
CAN communication can be readLAN-13
ACTIVE TEST*2Gives a drive signal to a load to check the
operation.SE-39
DRIVER SEAT CONTROL UNIT PART NUMBER Displays driver seat control unit part No. —
Monitor item [OPERATION or UNIT] Contents
MIR CON SW–UP “ON/OFF”ON/OFF status judged from the door mirror remote control switch (UP) signal is
displayed.
MIR CON SW–DN “ON/OFF”ON/OFF status judged from the door mirror remote control switch (DOWN) signal
is displayed.
MIR CON SW–RH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (RIGHT) signal
is displayed.
MIR CON SW–LH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (LEFT) signal s
displayed.
MIR CHNG SW–R “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
RIGHT) signal is displayed.
MIR CHNG SW–L “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
LEFT) signal is displayed.
SET SW “ON/OFF” ON/OFF status judged from the setting switch signal is displayed.
MEMORY SW1 “ON/OFF” ON/OFF status judged from the seat memory switch 1 signal is displayed.
MEMORY SW2 “ON/OFF” ON/OFF status judged from the seat memory switch 2 signal is displayed.
MIR/SE RH R–L “V” Voltage output from RH door mirror sensor (LH/RH) is displayed.
MIR/SE RH U–D “V” Voltage output from RH door mirror sensor (UP/DOWN) is displayed.
MIR/SE LH R–L “V” Voltage output from LH door mirror sensor (LH/RH) is displayed.
MIR/SE LH U–D “V” Voltage output from LH door mirror sensor (UP/DOWN) is displayed.