2007 INFINITI M35 brake sensor

FRONT DISC BRAKE
BR-23
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2007 April2007 M35/M45

It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang cylinder body with a wire so as not to stretch
brake hose.

Do not damage piston boot.

If any shim is subject to serious corrosion, replace it with a new one.

Always replace shim and shim cover as a set when replacing brake pads.

Keep rotor free from brake fluid.

Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-27, "
BRAKE
BURNISHING PROCEDURE" .
Removal and Installation of Brake PadNFS000SE
REMOVAL
1. Remove tires from vehicle with power tool.
2. Remove lower sliding pin bolt.
3. Hang cylinder body with a wire, and remove pads, pad retainers,
shims, and shim cover from torque member.
CAUTION:
When removing the pad retainer from the torque member,
lift it in the direction indicated by the arrow in the figure so
that it does not deform.
INSTALLATION
1. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to between pad and shim. Install shim,
shim cover, to pad.
2. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based
grease to between pad retainer and pad. Install pad retainers
and pads to torque member.
CAUTION:

Securely assemble pad retainers so that they are not
being lifted up from torque member.

Both inner and outer pads have a pad return system on
the pad retainer. Install pad return lever securely to pad
wear sensor.
3. Install cylinder body to torque member.
CAUTION:
In the case of replacing a pad with new one, check a brake fluid level in the reservoir tank because
brake fluid returns to master cylinder reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool (commercial service tool) to easily press piston.
4. Install lower sliding pin bolt, and tighten it to the specified torque. Refer to BR-22, "
Components" .
5. Check front disc brake for drag.
6. Install tires to vehicle.
SBR556E
SBR557E

BR-28
REAR DISC BRAKE
Revision: 2007 April2007 M35/M45
REAR DISC BRAKEPFP:44000
On-Board InspectionNFS000SH
PAD WEAR INSPECTION

Check pad thickness from an inspection hole on cylinder body.
Check using a scale if necessary.
ComponentsNFS000SI
Standard
Standard thickness : 8.5 mm (0.335 in)
Repair limit thickness : 2.0 mm (0.079 in)
BRA0010D
1. Union bolt 2. Brake hose 3. Copper washer
4. Cap 5. Bleed valve 6. Sliding pin bolt
7. Cylinder body 8. Piston seal 9. Piston
10. Piston boot 11. Retaining ring 12. Inner shim cover
13. Inner shim 14. Inner pad 15. Pad retainer
16. Outer pad 17. Outer shim 18. Sliding pin boot
19. Bushing 20. Torque member mounting bolt 21. Washer
22. Torque member 23. Pad wear sensor 24. Inner pad (RH)
Refer to GI-11, "
Components" and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
PFIA0705J

BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BRC
A
B
BRC
Revision: 2007 April2007 M35/M45
BRAKE CONTROL SYSTEM
VDC/TCS/ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Procedures without Cowl Top Cover ..... 3
Precautions for Brake System .................................. 3
Precautions for Brake Control .................................. 4
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
Commercial Service Tools ........................................ 5
ON-VEHICLE SERVICE ............................................. 6
Adjustment of Steering Angle Sensor Neutral Posi-
tion ........................................................................... 6
SYSTEM DESCRIPTION ............................................ 7
System Diagram ....................................................... 7
Functions .................................................................. 7
ABS ....................................................................... 7
EBD ....................................................................... 7
TCS ....................................................................... 8
VDC ....................................................................... 8
ECD ....................................................................... 8
Operation That Is Not "System Error" ...................... 8
ABS ....................................................................... 8
TCS ....................................................................... 8
VDC ....................................................................... 8
Hydraulic Circuit Diagram ........................................ 9
CAN Communication ................................................ 9
SYSTEM DESCRIPTION ...................................... 9
TROUBLE DIAGNOSIS ............................................ 10
Fail-Safe Function .................................................. 10
ABS, EBD SYSTEM ............................................ 10
VDC/TCS ............................................................ 10
How to Perform Trouble Diagnoses ....................... 10
BASIC CONCEPT ............................................... 10
DIAGNOSIS FLOW CHART ................................ 11
ASKING COMPLAINTS ...................................... 12
EXAMPLE OF DIAGNOSIS WORKSHEET ........ 12
Component Parts Location ..................................... 13
Schematic .............................................................. 14Wiring Diagram — VDC — ..................................... 15
Control Unit Input/Output Signal Standard ............. 21
REFERENCE VALUE FROM CONSULT-II ......... 21
CONSULT-II Functions (ABS) ................................ 23
CONSULT-II MAIN FUNCTION ........................... 23
CONSULT-II SETTING PROCEDURE ................ 23
Self-Diagnosis ........................................................ 24
OPERATION PROCEDURE ................................ 24
ERASE MEMORY ............................................... 24
DISPLAY ITEM LIST ........................................... 25
Data Monitor ........................................................... 28
OPERATION PROCEDURE ................................ 28
DISPLAY ITEM LIST ........................................... 28
Active Test .............................................................. 30
OPERATION PROCEDURE ................................ 30
TEST ITEMS ....................................................... 31
For Fast and Accurate Diagnosis ........................... 32
PRECAUTIONS FOR DIAGNOSIS ..................... 32
Basic Inspection ..................................................... 33
BASIC INSPECTION 1: BRAKE FLUID LEVEL,
LEAK INSPECTION AND BRAKE PAD .............. 33
BASIC INSPECTION 2: LOOSENESS OF
POWER SYSTEM TERMINALS AND BATTERY ... 33
BASIC INSPECTION 3: ABS WARNING LAMP,
BRAKE WARNING LAMP, VDC OFF INDICATOR
LAMP AND SLIP INDICATOR LAMP .................. 33
TROUBLE DIAGNOSIS FOR SYSTEM .................... 34
Wheel Sensor Circuit .............................................. 34
INSPECTION PROCEDURE .............................. 34
Engine System ....................................................... 36
INSPECTION PROCEDURE .............................. 36
ABS Actuator and Electric Unit (Control Unit) ........ 36
INSPECTION PROCEDURE .............................. 36
ABS Actuator and Electric Unit (Control Unit) Power
Supply and Ground Circuit ..................................... 37
INSPECTION PROCEDURE .............................. 37
ABS Motor and Motor Relay Circuit ........................ 38
INSPECTION PROCEDURE .............................. 38
Solenoid, VDC Change-Over Valve and Actuator
Relay Circuit ........................................................... 39

BRC-2Revision: 2007 April2007 M35/M45 INSPECTION PROCEDURE ............................... 39
Pressure Sensor Circuit .......................................... 40
INSPECTION PROCEDURE ............................... 40
Steering Angle Sensor Circuit ................................. 41
INSPECTION PROCEDURE ............................... 41
Stop Lamp Switch Circuit ........................................ 43
INSPECTION PROCEDURE ............................... 43
Yaw Rate/Side G Sensor Circuit ............................. 44
INSPECTION PROCEDURE ............................... 44
Brake Fluid Level Switch Circuit ............................. 46
INSPECTION PROCEDURE ............................... 46
RAS Control Unit Circuit (With RAS) ...................... 47
INSPECTION PROCEDURE ............................... 47
ICC Sensor Integrated Unit Circuit (With ICC) ........ 48
INSPECTION PROCEDURE ............................... 48
CAN Communication Circuit ................................... 48
INSPECTION PROCEDURE ............................... 48
VDC OFF Switch Circuit ......................................... 49
INSPECTION PROCEDURE ............................... 49
Parking Brake Switch Circuit .................................. 50
INSPECTION PROCEDURE ............................... 50
Warning Lamp and Indicator Lamp Circuit ............. 50
INSPECTION PROCEDURE ............................... 50
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 51
Excessive ABS Function Operation Frequency ...... 51
Unexpected Pedal Reaction ................................... 51The Braking Distance Is Long ................................. 52
ABS Function Does Not Operate ............................ 52
Pedal Vibration or ABS Operation Sound Occurs ... 52
Vehicle Jerks During VDC/TCS/ABS Control .......... 53
WHEEL SENSOR ...................................................... 54
Removal and Installation ......................................... 54
COMPONENT ...................................................... 54
REMOVAL ............................................................ 54
INSTALLATION .................................................... 54
SENSOR ROTOR ...................................................... 56
Removal and Installation ......................................... 56
REMOVAL ............................................................ 56
INSTALLATION .................................................... 56
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 57
Removal and Installation ......................................... 57
COMPONENT ...................................................... 57
REMOVAL ............................................................ 57
INSTALLATION .................................................... 58
G-SENSOR ................................................................ 59
Removal and Installation ......................................... 59
REMOVAL ............................................................ 59
INSTALLATION .................................................... 59
STEERING ANGLE SENSOR ................................... 60
Removal and Installation ......................................... 60
REMOVAL ............................................................ 60
INSTALLATION .................................................... 60

PREPARATION
BRC-5
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
PREPARATIONPFP:00002
Special Service ToolsNFS000Q2
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service ToolsNFS000Q3
Tool number
(Kent-Moore No.)
Tool nameDescription
ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.19 in) dia.
Installing rear sensor rotor ST27863000
(—)
Drift
a: 74.5 mm (2.93 in) dia.
b: 62.5 mm (2.46 in) dia.
KV40104710
(—)
a: 76.3 mm (3.00 in) dia.
b: 67.9 mm (2.67 in) dia.
ZZA0701D
ZZA0832D
ZZA0832D
Tool nameDescription
1. Flare nut crowfoot
a: 10 mm (0.39 in) / 12mm (0.47 in)
2. Torque wrenchInstalling brake tube
S-NT360

SYSTEM DESCRIPTION
BRC-7
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
SYSTEM DESCRIPTIONPFP:00000
System DiagramNFS000Q5
FunctionsNFS000Q6
ABS

Anti-Lock Brake System is a function that detects wheel revolution while braking, electronically controls
braking force, and prevents wheel locking during sudden braking. It improves handling stability and
maneuverability for avoiding obstacles.

Electrical system diagnosis by CONSULT-II is available.
EBD

Electronic Brake force Distribution is a following function. ABS actuator and electric unit (control unit)
detects subtle slippages between the front and rear wheels during braking. Then it electronically controls
the rear braking force (brake fluid pressure) to reducing and reduces rear wheel slippage. Accordingly it
improves vehicle stability.

Electrical system diagnosis by CONSULT-II is available.
1. Electric line 2. Brake hydraulic line 3. ECM
4. TCM 5. Steering angle sensor 6. Warning lamp, indicator lamp
(combination meter)
7. AWD control unit
(AWD models)8. ICC sensor integrated unit
(with ICC)9. RAS control unit
(with RAS)
10. Injector operation signal 11. CAN communication 12. Front RH wheel sensor
13. Front LH wheel sensor 14. Master cylinder 15. ABS actuator and electric unit (con-
trol unit)
16. VDC OFF switch 17. Yaw rate/side G sensor 18. Rear RH wheel sensor
19. Rear LH wheel sensor
SFIA2722J

BRC-8
[VDC/TCS/ABS]
SYSTEM DESCRIPTION
Revision: 2007 April2007 M35/M45
TCS

Traction Control System is a function that electronically controls engine torque, brake fluid pressure and
A/T gear position to ensure the optimum slippage ratio at drive wheels by computing wheel speed signals
from 4 wheel sensors. When ABS actuator and electric unit (control unit) detects a spin at drive wheels
(rear wheels), it compares wheel speed signals from all 4 wheels. At this time, LH and RH rear brake fluid
pressure are controlled, while fuel being cut to engine and throttle valve being closed to reduce engine
torque by the control unit. Further more, throttle position is continuously controlled to ensure the optimum
engine torque at all times.

During TCS operation, it informs driver of system operation by flashing SLIP indicator lamp.

Electrical system diagnosis by CONSULT-II is available.
VDC

Vehicle Dynamics Control system detects driver's steering operation amount and brake pedal travel from
steering angle sensor and pressure sensor. Using information from yaw rate/side G sensor and wheel
sensor, VDC judges driving condition (conditions of under steer and over steer) to improve vehicle driving
stability by controlling brake application to 4 wheels and engine output.

During VDC operation, it informs driver of system operation by flashing SLIP indicator lamp.

Electrical system diagnosis by CONSULT-II is available.
ECD
Receives deceleration degree commandment value signal from ICC sensor integrated unit, and controls brake
fluid pressure with the motor [built-in ABS actuator and electric unit (control unit)].
Operation That Is Not "System Error" NFS000Q7
ABS

When starting engine or just after starting vehicle, brake pedal may vibrate or the motor operating sound
may be heard from engine room. This is a normal states of the operation check.

During ABS operation, brake pedal lightly vibrates and a mechanical sound may be heard. This is normal.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
TCS

Depending on road circumstances, driver may have a sluggish feel. This is normal, because optimum
traction has highest priority under TCS operation.

When vehicle is passing through a road where surface friction varies, downshifting or depressing acceler-
ator pedal fully may activate TCS temporarily.
VDC

During VDC operation, body and brake pedal lightly vibrate and mechanical sounds may be heard. This is
normal.

If vehicle is rotated on turn table, or rolled and rocked on ship, ABS warning lamp, VDC OFF indicator
lamp, and SLIP indicator lamp may turn on. In this case, start engine on normal road again. If ABS warn-
ing lamp, VDC OFF indicator lamp, and SLIP indicator lamp turn off after restart, it is normal.

When starting TCS or VDC under rapid acceleration or hard turn, operating sound by brake pedal is gen-
erated. However, this is not malfunction. This is because TCS and VDC are functioning normally.

VDC may not operate normally or ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp
may turn on when driving special roads with extremely steep slant (banks on circuit road and so on.) How-
ever, it is not malfunction when returning to a normal state after restarting the engine. In that case, be sure
to erase the memory of self-diagnosis. Refer to BRC-24, "
ERASE MEMORY" .

Yaw rate /side G sensor malfunction may occur under hard turn like spin turn, rapid acceleration turn, drift
run, etc., when VDC function is OFF (VDC OFF switch is turned on). It is not malfunction if it is possible to
return to a normal position after restarting engine. Then erase the memory of self-diagnosis. Refer to
BRC-24, "
ERASE MEMORY" .

VDC OFF indicator lamp and SLIP indicator lamp may simultaneously turn on when low tire pressure
warning lamp turns on. This is not a VDC system error but results from characteristic change of tires.

TROUBLE DIAGNOSIS
BRC-21
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2007 April2007 M35/M45
Control Unit Input/Output Signal StandardNFS000RH
REFERENCE VALUE FROM CONSULT-II
CAUTION:
The display shows ABS actuator and electric unit (control unit) calculation data, so a normal value
might be displayed even in the event the output circuit (harness) is open or short-circuited.
Monitor item Display contentData monitor
ConditionReference value in nor-
mal operation
FR LH SENSOR
FR RH SENSOR
RR LH SENSOR
RR RH SENSORWheel speedVehicle stopped 0 [km/h (MPH)]
Vehicle running (Note 1)Nearly matches the
speedometer display
(± 10 % or less)
STOP LAMP SW Brake pedal operationWhen brake pedal is depressed ON
When brake pedal is not depressed OFF
BATTERY VOLTBattery voltage supplied to the ABS
actuator and electric unit (control unit)Ignition switch ON 10 – 16 V
GEAR Gear position determined by TCM1st gear
2nd gear
3rd gear
4th gear
5th gear1
2
3
4
5
SLCT LVR POSI A/T select lever positionP position
R position
N position
D positionP
R
N
D
OFF SW VDC OFF switchVDC OFF switch :ON
(When VDC OFF indicator lamp is ON)ON
VDC OFF switch :OFF
(When VDC OFF indicator lamp is OFF)OFF
YAW RATE SENYaw rate detected by yaw rate/side G
sensorWhen vehicle stop Approx. 0 d/s
When vehicle turning (–75 to 75 d/s)
4WD MODE MON
(Note 2)AWD activated Engine running AUTO
ACCEL POS SIG Throttle actuator opening/closing is dis-
played (linked with accelerator pedal)Accelerator pedal not depressed
(Engine stopped)0 %
Depress accelerator pedal
(Engine stopped)0 - 100 %
SIDE G-SENSOR Transverse G detected by side G sensorVehicle stopped
Approx. 0 m/s
2
Vehicle turning rightNegative value
(m/s2 )
Vehicle turning leftPositive value
(m/s
2 )
STR ANGLE SIGSteering angle detected by steering
angle sensorStraight-ahead Approx. 0°
Steering wheel turned –720 to 720°
PRESS SENSORBrake fluid pressure detected by pres-
sure sensorWith ignition switch turned ON and brake
pedal releasedApprox. 0 bar
With ignition switch turned ON and brake
pedal depressed–40 to 300 bar
ENGINE RPM Engine speedWith engine stopped 0 rpm
Engine runningAlmost in accordance
with tachometer display