2007 INFINITI FX35 service

ATC-3
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2006 July 2007 FX35/FX45
COMPONENT INSPECTION ...........................
. . 111
Intake Sensor Circuit ........................................... .. 112
COMPONENT DESCRIPTION ........................ .. 112
DIAGNOSIS PROCEDURE FOR INTAKE SEN-
SOR ................................................................. .. 112
COMPONENT INSPECTION ........................... .. 113
CONTROLLER ...................................................... ..114
Removal and Installation of A/C and AV Switch .. .. 114
REMOVAL ........................................................ .. 114
INSTALLATION ................................................ .. 114
AUTO AMP ............................................................ ..115
Removal and Installation of Unified Meter and A/C
Amp. .................................................................... .. 115
REMOVAL ........................................................ .. 115
INSTALLATION ................................................ .. 115
AMBIENT SENSOR ............................................... ..116
Removal and Installation ..................................... .. 116
REMOVAL ........................................................ .. 116
INSTALLATION ................................................ .. 116
IN-VEHICLE SENSOR ........................................... ..117
Removal and Installation ..................................... .. 117
REMOVAL ........................................................ .. 117
INSTALLATION ................................................ .. 117
SUNLOAD SENSOR ............................................. ..118
Removal and Installation ..................................... .. 118
REMOVAL ........................................................ .. 118
INSTALLATION ................................................ .. 118
INTAKE SENSOR .................................................. ..119
Removal and Installation ..................................... .. 119
REMOVAL ........................................................ .. 119
INSTALLATION ................................................ .. 119
BLOWER UNIT ...................................................... . 120
Removal and Installation ..................................... . 120
REMOVAL ........................................................ . 120
INSTALLATION ................................................ . 120
Disassembly and Assembly ................................ . 121
BLOWER MOTOR ................................................. . 122
Removal and Installation ..................................... . 122
REMOVAL ........................................................ . 122
INSTALLATION ................................................ . 122
INTAKE DOOR MOTOR ........................................ . 123
Removal and Installation ..................................... . 123
REMOVAL ........................................................ . 123
INSTALLATION ................................................ . 123
IN-CABIN MICROFILTER ...................................... . 124
Removal and Installation ..................................... . 124
FUNCTION ....................................................... . 124
REPLACEMENT TIMING ................................. . 124
REPLACEMENT PROCEDURES .................... . 124
HEATER & COOLING UNIT ASSEMBLY ............. . 125
Removal and Installation ..................................... . 125
REMOVAL ........................................................ . 125
INSTALLATION ................................................ . 126
Disassembly and Assembly ................................ . 128
MODE DOOR MOTOR .......................................... . 130
Removal and Installation ..................................... . 130
REMOVAL ........................................................ . 130
INSTALLATION ................................................ . 130 AIR MIX DOOR MOTOR ........................................
.131
Removal and Installation ..................................... .131
REMOVAL ........................................................ .131
INSTALLATION ................................................ .131
HEATER CORE ...................................................... .132
Removal and Installation ..................................... .132
REMOVAL ........................................................ .132
INSTALLATION ................................................ .132
DUCTS AND GRILLES .......................................... .133
Removal and Installation ..................................... .133
COMPONENT LAYOUT ................................... .133
REMOVAL ........................................................ .133
INSTALLATION ................................................ .136
REFRIGERANT LINES .......................................... .137
HFC-134a (R-134a) Service Procedure .............. .137
SETTING OF SERVICE TOOLS AND EQUIP-
MENT ............................................................... .137
Components ........................................................ .139
VQ35DE ........................................................... .139
VK45DE ............................................................ .140
Removal and Installation of Compressor ............. .140
REMOVAL ........................................................ .140
INSTALLATION ................................................ .142
Removal and Installation of Compressor Clutch . .142
REMOVAL ........................................................ .142
INSTALLATION ................................................ .144
Removal and Installation of Low-pressure Flexible
Hose .................................................................... .146
REMOVAL ........................................................ .146
INSTALLATION ................................................ .147
Removal and Installation of High-pressure Flexible
Hose .................................................................... .147
REMOVAL ........................................................ .147
INSTALLATION ................................................ .148
Removal and Installation of Low-pressure Pipe 1
(Engine Compartment) ........................................ .148
REMOVAL ........................................................ .148
INSTALLATION ................................................ .149
Removal and Installation of High-pressure Pipe 1
and 2 (Engine Compartment) .............................. .149
REMOVAL ........................................................ .149
INSTALLATION ................................................ .150
Removal and Installation of Low-pressure Pipe 2
and High-pressure Pipe 3 .................................... .150
REMOVAL ........................................................ .150
INSTALLATION ................................................ .151
Removal and Installation of Liquid Tank .............. .152
REMOVAL ........................................................ .152
INSTALLATION ................................................ .152
Removal and Installation of Condenser ............... .153
REMOVAL ........................................................ .153
INSTALLATION ................................................ .154
Removal and Installation of Refrigerant Pressure
Sensor ................................................................. .154
REMOVAL ........................................................ .154
INSTALLATION ................................................ .154
Removal and Installation of Evaporator ............... .154
REMOVAL ........................................................ .154
INSTALLATION ................................................ .155

ATC-4Revision: 2006 July 2007 FX35/FX45
Removal and Installation of Expansion Valve ......
.155
REMOVAL ........................................................ .155
INSTALLATION ................................................. .155
Checking for Refrigerant Leaks ........................... .156
Checking System for Leaks Using the Fluorescent
Leak Detector ...................................................... .156
Dye Injection ........................................................ .156
Electrical Leak Detector ....................................... .157
PRECAUTIONS FOR HANDLING LEAK DETECTOR ......................................................
.157
CHECKING PROCEDURE ............................... .158
SERVICE DATA AND SPECIFICATIONS (SDS) ... .160
Compressor ......................................................... .160
Lubricant .............................................................. .160
Refrigerant ........................................................... .160
Engine Idling Speed ............................................. .160
Belt Tension ......................................................... .160

PRECAUTIONS ATC-5
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2006 July 2007 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NJS000D5
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectNJS000D6
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″ LOCK ″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

PRECAUTIONS ATC-7
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2006 July 2007 FX35/FX45
CONTAMINATED REFRIGERANT
If a refrigerant other than pure HFC-134a (R-134a) is identified in a vehicle, take appropriate steps
shown below:

Explain to the customer that environmental regulations prohibit the release of contaminated refrigerant
into the atmosphere.

Explain that recovery of the contaminated refrigerant could damage service equipment and refrigerant
supply.

Suggest the customer return the vehicle to the location of previous service where the contamination may
have occurred.

In case of repairing, recover the refrigerant using only dedicated equipment and containers. Never
recover contaminated refrigerant into the existing service equipment. If the facility does not have
dedicated recovery equipment, contact a local refrigerant product retailer for available service. This refrig-
erant must be disposed of in accordance with all federal and local regulations. In addition, replacement of
all refrigerant system components on the vehicle is recommended.

If the vehicle is within the warranty period, the air conditioner warranty is void. Please contact Nissan Cus-
tomer Affairs for further assistance.
General Refrigerant PrecautionsNJS000D9
WARNING:

Avoid breathing A/C refrigerant and lubricant vapor or mist. Exposure may irritate eyes, nose and
throat. Remove HFC-134a (R-134a) from the A/C system, using certified service equipment meet-
ing requirements of SAE J-2210 [HFC-134a (R-134a) recycling equipment], or J-2209 [HFC-134a (R-
134a) recovery equipment]. If accidental system discharge occurs, ventilate work area before
resuming service. Additional health and safety information may be obtained from refrigerant and
lubricant manufacturers.

Never release refrigerant into the air. Use approved recovery/recycling equipment to capture the
refrigerant every time an air conditioning system is discharged.

Always wear eye and hand protection (goggles and gloves) when working with any refrigerant or
air conditioning system.

Never store or heat refrigerant containers above 52 °C (126 °F).

Never heat a refrigerant container with an open flame; if container warming is required, place the
bottom of the container in a warm pail of water.

Never intentionally drop, puncture, or incinerate refrigerant containers.

Keep refrigerant away from open flames: poisonous gas will be produced if refrigerant burns.

Refrigerant will displace oxygen, therefore be certain to work in well ventilated areas to prevent
suffocation.

Never pressure test or leak test HFC-134a (R-134a) service equipment and/or vehicle air condition-
ing systems with compressed air during repair. Some mixtures of air and HFC-134a (R-134a) have
been shown to be combustible at elevated pressures. These mixtures, if ignited, may cause injury
or property damage. Additional health and safety information may be obtained from refrigerant
manufacturers.

PRECAUTIONS ATC-13
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2006 July 2007 FX35/FX45

After connecting line, perform leak test and make sure that there is no leakage from connections.
When the refrigerant leaking point is found, disconnect that line and replace the O-ring. Then
tighten connections of seal seat to the specified torque.
Precautions for Servicing CompressorNJS000DB

Plug all openings to prevent moisture and foreign matter from entering.

When the compressor is removed, store it in the same way at it is when mounted on the car.

When replacing or repairing compressor, follow “Maintenance of Lubricant Quantity in Compres-
sor” exactly. Refer to AT C - 2 7 , "
Maintenance of Lubricant Quantity in Compressor" .

Keep friction surfaces between clutch and pulley clean. If the surface is contaminated with lubri-
cant, wipe it off by using a clean waste cloth moistened with thinner.

After compressor service operation, turn the compressor shaft by hand more than five turns in
both directions. This will equally distribute lubricant inside the compressor. After the compressor
is installed, let the engine idle and operate the compressor for one hour.

After replacing the compressor magnet clutch, apply voltage to the new one and check for normal
operation.
Precautions for Service EquipmentNJS000DC
RECOVERY/RECYCLING EQUIPMENT
Be certain to follow the manufacturer’s instructions for machine operation and machine maintenance. Never
introduce any refrigerant other than that specified into the machine.
ELECTRICAL LEAK DETECTOR
Be certain to follow the manufacturer’s instructions for tester operation and tester maintenance.
RHA861F

ATC-14
PRECAUTIONS
Revision: 2006 July 2007 FX35/FX45
VACUUM PUMP
The lubricant contained inside the vacuum pump is not compatible
with the specified lubricant for HFC-134a (R-134a) A/C systems.
The vent side of the vacuum pump is exposed to atmospheric pres-
sure. So the vacuum pump lubricant may migrate out of the pump
into the service hose. This is possible when the pump is switched off
after evacuation (vacuuming) and hose is connected to it.
To prevent this migration, use a manual valve placed near the hose-
to-pump connection, as follows.

Usually vacuum pumps have a manual isolator valve as part of
the pump. Close this valve to isolate the service hose from the
pump.

For pumps without an isolator, use a hose equipped with a man-
ual shut-off valve near the pump end. Close the valve to isolate
the hose from the pump.

If the hose has an automatic shut-off valve, disconnect the hose
from the pump. As long as the hose is connected, the valve is
open and lubricating oil may migrate.
Some one-way valves open when vacuum is applied and close
under no vacuum condition. Such valves may restrict the pump’s
ability to pull a deep vacuum and are not recommended.
MANIFOLD GAUGE SET
Be certain that the gauge face indicates HFC-134a or R-134a. Be
sure the gauge set has 1/2 ″-16 ACME threaded connections for ser-
vice hoses. Confirm the set has been used only with refrigerant
HFC-134a (R-134a) and specified lubricants.
SERVICE HOSES
Be certain that the service hoses display the markings described
(colored hose with black stripe). All hoses must include positive shut-
off devices (either manual or automatic) near the end of the hoses
opposite to the manifold gauge.
RHA270DA
SHA533D
RHA272D

PRECAUTIONS ATC-15
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2006 July 2007 FX35/FX45
SERVICE COUPLERS
Never attempt to connect HFC-134a (R-134a) service couplers to a
CFC-12 (R-12) A/C system. The HFC-134a (R-134a) couplers will
not properly connect to the CFC-12 (R-12) system. However, if an
improper connection is attempted, discharging and contamination
may occur.
REFRIGERANT WEIGHT SCALE
Verify that no refrigerant other than HFC-134a (R-134a) and speci-
fied lubricants have been used with the scale. If the scale controls
refrigerant flow electronically, the hose fitting must be 1/2
″ -16
ACME.
CHARGING CYLINDER
Using a charging cylinder is not recommended. Refrigerant may be vented into air from cylinder’s top valve
when filling the cylinder with refrigerant. Also, the accuracy of the cylinder is generally less than that of an
electrical scale or of quality recycle/recharge equipment.
Shut-off valve rotation A/C service valve
Clockwise Open
Counterclockwise Close
RHA273D
RHA274D

ATC-16
PRECAUTIONS
Revision: 2006 July 2007 FX35/FX45
Precautions for Leak Detection DyeNJS000DD

The A/C system contains a fluorescent leak detection dye used for locating refrigerant leaks. An ultraviolet
(UV) lamp is required to illuminate the dye when inspecting for leaks.

Always wear fluorescence enhancing UV safety goggles to protect your eyes and enhance the visibility of
the fluorescent dye.

The fluorescent dye leak detector is not a replacement for an electrical leak detector (SST: J-41995). The
fluorescent dye leak detector should be used in conjunction with an electrical leak detector (SST: J-41995)
to pin-point refrigerant leaks.

For the purpose of safety and customer’s satisfaction, read and follow all manufacture’s operating instruc-
tions and precautions prior to performing the work.

A compressor shaft seal should not necessarily be repaired because of dye seepage. The compressor
shaft seal should only be repaired after confirming the leak with an electrical leak detector (SST: J-41995).

Always remove any remaining dye from the leak area after repairs are completed to avoid a misdiagnosis
during a future service.

Never allow dye to come into contact with painted body panels or interior components. If dye is spilled,
clean immediately with the approved dye cleaner. Fluorescent dye left on a surface for an extended period
of time cannot be removed.

Never spray the fluorescent dye cleaning agent on hot surfaces (engine exhaust manifold, etc.).

Never use more than one refrigerant dye bottle (1/4 ounce /7.4 cc) per A/C system.

Leak detection dyes for HFC-134a (R-134a) and CFC-12 (R-12) A/C systems are different. Never use
HFC-134a (R-134a) leak detection dye in CFC-12 (R-12) A/C system, or CFC-12 (R-12) leak detection
dye in HFC-134a (R-134a) A/C system, or A/C system damage may result.

The fluorescent properties of the dye will remain for three years or a little over unless a compressor mal-
function occurs.
IDENTIFICATION
NOTE:
Vehicles with factory installed fluorescent dye have a green label.
Vehicles without factory installed fluorescent dye have a blue label.
IDENTIFICATION LABEL FOR VEHICLE
Vehicles with factory installed fluorescent dye have the identification label on the front side of hood.