2007 INFINITI FX35 sensor

DI-24
COMBINATION METERS
Revision: 2006 July 2007 FX35/FX45
4. QUESTION 4
During driving, does the fuel gauge pointer move gradually toward EMPTY position?
YES >> Check the fuel level sensor unit. Refer to DI-24, "FUEL LEVEL SENSOR UNIT" .
NO >> The float arm may interfere or bind with any of the components in the fuel tank.
Odo/Trip Meter and Illumination Control Switch InspectionNKS002ZT
Symptom: Illumination control does not operate.
1. CHECK ODO/TRIP METER AND ILLUMINATION CONTROL SWITCH
1. Remove odo/trip meter and illumination control switch. Refer to DI-27, "
Removal and Installation of Odo/
Trip Meter and Illumination Control Switch" .
2. Check continuity odo/trip meter and illumination control switch. Refer to DI-24, "
ODO/TRIP METER AND
ILLUMINATION CONTROL SWITCH" .
OK or NG
OK >> Replace combination meter.
NG >> Replace odo/trip meter and illumination control switch.
Electrical Components InspectionNKS002ZW
ODO/TRIP METER AND ILLUMINATION CONTROL SWITCH
Check continuity between terminals 25, 26, 35 or 36 and 27.
FUEL LEVEL SENSOR UNIT
For removal, refer to FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY" .
Fuel Level Sensor Unit and Fuel Pump (Main)
Check the resistance between terminals 2 and 5.
*1 and *2: When float rod is in contact with stopper.

If the results of check are NG, check the fuel level sensor unit
and fuel pump (main) harness. Refer to DI-25, "
Fuel Level Sen-
sor Unit and Pump (Main) Harness" .
Terminal Condition Continuity
25
27 Illumination control switch (–) is pressed. Yes
Illumination control switch (–) is released. No
26 Illumination control switch (+) is pressed. Yes
Illumination control switch (+) is released. No
35 Trip transfer switch is pressed. Yes
Trip transfer switch is released. No
36 Trip reset switch is pressed. Yes
Trip reset switch is released. No
SKIB8529E
Terminal Float position [mm (in)] Resistance
value [ Ω]
25 *1 Full 236 (9.29) Approx. 3
*2 Empty 29 (1.14) Approx. 80
SKIB3550J

COMBINATION METERS DI-25
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
Fuel Level Sensor Unit and Pump (Main) Harness
Check continuity at following terminals.

If the results of check are NG, replace fuel pump assembly. If the
results of check are OK, replace fuel level sensor unit.
Fuel Level Sensor Unit (Sub)
Check resistance between terminals 1 and 2.
*1 and *2: When float rod is in contact with stopper.
Removal and Installation of Combination MeterNKS003IC
Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
Disassembly and Assembly of Combination MeterNKS002ZY
Terminal Continuity
2 - Signal terminal (A) Ye s
5 - Ground terminal (B)
SKIB3551J
Terminal Float position [mm (in)] Resistance
value [ Ω]
12 *1 Full 6 (0.24) Approx. 3
*2 Empty 203 (7.99) Approx. 48
SKIB8530E
1. Rear cover 2. Screws 3. Plate
4. Unified meter control unit assembly 5. Front cover 6. Reinforcing metal
7. Switch and meter housing
SKIA5790E

DI-28
UNIFIED METER AND A/C AMP
Revision: 2006 July 2007 FX35/FX45
UNIFIED METER AND A/C AMPPFP:27760
System DescriptionNKS00300

For the unified meter and A/C amp., the signal required for controlling the combination meter are inte-
grated in the A/C auto amp.

The unified meter and A/C amp. corresponds to a CONSULT-II function (self-diagnosis results, CAN diag-
nosis support monitor, data monitor).
COMBINATION METER CONTROL FUNCTION

Unified meter and A/C amp. receives necessary information for combination meter from each unit by CAN
communication.

Unified meter and A/C amp. transmits a signals with communication line (TX, RX) between unified meter
and A/C amp. and combination meter.
Input/output signals between unified meter and A/C amp. and combination meter.
NOTE:
Combination meter performs fail-safe operation when unified meter and A/C amp. communication is malfunctioning. Refer to DI-8,
"FAIL-SAFE" . Unit Input Output
Unified meter and A/C amp.

Seat belt buckle switch signal (Driver's side)

Parking brake signal

Illumination control nighttime required signal

Refuel status signal

Low-fuel warning lamp condition signal

Combination meter receive error signal

Delivery destination data signal

Combination meter specifications signal

Vehicle speed signal (8-pulse)

Engine speed signal

Engine coolant temperature signal

Fuel level sensor signal (resistance value)

Malfunction indicator lamp signal

ABS warning lamp signal

Low tire pressure warning lamp signal

Run-flat tire warning lamp signal

Brake warning lamp signal

A/T CHECK warning lamp signal

ICC warning lamp signal

Oil pressure switch signal

Door switch signal

AWD warning lamp signal

Key warning lamp signal

VDC OFF indicator lamp signal

SLIP indicator lamp signal

CRUISE indicator lamp signal

SET indicator lamp signal

High beam request signal

Turn indicator signal

Snow mode switch signal

ICC system display signal

Shift position indicator signal

Manual mode indicator signal

Manual mode gear position signal

CAN communication condition signal of A/T

Position lights request signal

Buzzer output signal

LANE DEPARTURE WARNING SYSTEM DI-93
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
Display Item
NOTE:

When a DTC is detected, the LDW system dose not operate.

When the DTC except “ABNRML TEMP DETECT [C1B03] ” is detected, the LDW indicator lamp turns ON.

When the DTC “ABNRML TEMP DETECT [C1B03] ” is detected, the LDW system ON indicator lamp blinks.
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch any of “ALL SIGNALS” and “SELECTION FROM MENU” on selection screen.
3. Touch “START”.
4. Display the data monitor.
5. If necessary, touch “COPY” in turn, and print data.
Monitored Item
Display item [Code] Malfunctions detected where... Reference
page
CAMERA UNIT MALF [C1B00] LDW camera unit internal malfunction DI-97
CAM AIMING INCMP [C1B01] LDW camera aiming is not adjusted.DI-97
VHCL SPD DATA MALF [C1B02] LDW camera unit detected different vehicle speed signal from TCM and ABS
actuator and electric unit (control unit). DI-97
ABNRML TEMP DETECT [C1B03] Temperature around LDW camera unit is excessively high.
DI-98
CAN COMM CIRCUIT [U1000] LDW camera unit detected CAN communication malfunction.DI-98
CONTROL UNIT (CAN) [U1010] LDW camera unit detected internal CAN communication circuit malfunction.DI-98
Monitored Item [unit] Description
MAIN SW [ON/OFF] Displays [ON/OFF] status as judged from LDW switch signal.
SW ON LAMP [ON/OFF] Displays [ON/OFF] status of LDW system ON indicator signal output.
INDICATE LAMP [ON/OFF] Displays [ON/OFF] status of LDW indicator signal output.
BUZZER OUTPUT [ON/OFF] Displays [ON/OFF] status of LDW chime operation signal output.
LDW INACCURAT [ON/OFF] Displays LDW camera unit status.
VHCL SPD SE [km/h] or [mph] Displays vehicle speed calculated by LDW camera unit through CAN communication [ABS
actuator and electric unit (control unit) transmits wheel sensor signal through CAN commu-
nication].
VHCL SPD AT [km/h] or [mph] Displays vehicle speed calculated from A/T vehicle speed sensor by LDW camera unit
through CAN communication (TCM transmits A/T vehicle speed sensor signal through CAN
communication).
TURN SIGNAL [OFF/LH/RH] Displays “Turn signal” status, determined from BCM through CAN communication.
LANE DETCT LH [ON/OFF] Displays left lane marker is detected.
LANE DETCT RH [ON/OFF] Displays right lane marker is detected.
CROSS LANE LH [ON/OFF] Displays vehicle is crossing left lane.
CROSS LANE RH [ON/OFF] Displays vehicle is crossing right lane.
WARN LANE LH [ON/OFF] Displays warning for left lane.
WARN LANE RH [ON/OFF] Displays warning for right lane.
VALID POS LH [VLD/INVLD] Displays lateral position for left lane marker is valid.
VALID POS RH [VLD/INVLD] Displays lateral position for right lane marker is valid.
AIMING DONE [OK/NG] Displays camera aiming done.
AIMING RESULT [OK/NOK] Displays camera aiming result.
FCTRY AIM YAW [deg] Displays camera unit installation condition.
FCTRY AIM ROL [deg] Displays camera unit installation condition.

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D E
F
G H
I
J
K L
M
SECTION
A
EC
Revision: 2006 July 2007 FX35/FX45
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
DTC No. Index .................................................... ... 15
Alphabetical Index ............................................... ... 19
PRECAUTIONS ..................................................... ... 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 23
Precautions for Procedures without Cowl Top Cover ... 23
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 23
Precaution ........................................................... ... 24
PREPARATION ...................................................... ... 27
Special Service Tools .......................................... ... 27
Commercial Service Tools ................................... ... 28
ENGINE CONTROL SYSTEM ............................... ... 29
System Diagram .................................................. ... 29
Multiport Fuel Injection (MFI) System ................. ... 30
Electronic Ignition (EI) System ............................ ... 32
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 33
AIR CONDITIONING CUT CONTROL .................. ... 34
Input/Output Signal Chart .................................... ... 34
System Description ............................................. ... 34
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 35
System Description ............................................. ... 35
Component Description ....................................... ... 36
CAN COMMUNICATION ....................................... ... 37
System Description ............................................. ... 37
EVAPORATIVE EMISSION SYSTEM .................... ... 38
Description .......................................................... ... 38
Component Inspection ........................................ ... 41
Removal and Installation ..................................... ... 42
How to Detect Fuel Vapor Leakage .................... ... 42
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 45
System Description ............................................. ... 45
Diagnostic Procedure .......................................... ... 46
Component Inspection ........................................ ... 48 POSITIVE CRANKCASE VENTILATION ..............
... 50
Description ........................................................... ... 50
Component Inspection ......................................... ... 50
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... ... 52
Description ........................................................... ... 52
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 53
Introduction .......................................................... ... 53
Two Trip Detection Logic ..................................... ... 53
Emission-Related Diagnostic Information ............ ... 54
Malfunction Indicator Lamp (MIL) ........................ ... 67
OBD System Operation Chart ............................. ... 71
BASIC SERVICE PROCEDURE ............................ ... 76
Basic Inspection .................................................. ... 76
Idle Speed and Ignition Timing Check ................. ... 81
Procedure After Replacing ECM ......................... ... 82
VIN Registration .................................................. ... 82
Accelerator Pedal Released Position Learning ... ... 83
Throttle Valve Closed Position Learning .............. ... 83
Idle Air Volume Learning ..................................... ... 83
Fuel Pressure Check ........................................... ... 85
TROUBLE DIAGNOSIS ......................................... ... 87
Trouble Diagnosis Introduction ............................ ... 87
DTC Inspection Priority Chart .............................. ... 93
Fail-Safe Chart .................................................... ... 95
Symptom Matrix Chart ......................................... ... 96
Engine Control Component Parts Location ......... .100
Vacuum Hose Drawing ........................................ .106
Circuit Diagram .................................................... .107
ECM Harness Connector Terminal Layout .......... .109
ECM Terminals and Reference Value .................. .109
CONSULT-II Function (ENGINE) ......................... .118
Generic Scan Tool (GST) Function ...................... .129
CONSULT-II Reference Value in Data Monitor .... .132
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .134
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .137
Description ........................................................... .137
Testing Condition ................................................. .137

EC-2Revision: 2006 July 2007 FX35/FX45
Inspection Procedure ...........................................
.137
Diagnostic Procedure .......................................... .138
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .147
Description ........................................................... .147
Diagnostic Procedure .......................................... .147
POWER SUPPLY AND GROUND CIRCUIT .......... .148
Wiring Diagram .................................................... .148
Diagnostic Procedure .......................................... .149
Ground Inspection ............................................... .153
DTC U1000, U1001 CAN COMMUNICATION LINE .155
Description ........................................................... .155
On Board Diagnosis Logic ................................... .155
DTC Confirmation Procedure .............................. .155
Wiring Diagram .................................................... .156
Diagnostic Procedure .......................................... .157
DTC U1010 CAN COMMUNICATION .................... .158
Description ........................................................... .158
On Board Diagnosis Logic ................................... .158
DTC Confirmation Procedure .............................. .158
Diagnostic Procedure .......................................... .159
DTC P0011, P0021 IVT CONTROL ....................... .160
Description ........................................................... .160
CONSULT-II Reference Value in Data Monitor Mode .160
On Board Diagnosis Logic ................................... .161
DTC Confirmation Procedure .............................. .161
Diagnostic Procedure .......................................... .162
Component Inspection ......................................... .163
Removal and Installation ..................................... .163
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ................................................................. .164
Description ........................................................... .164
CONSULT-II Reference Value in Data Monitor Mode .164
On Board Diagnosis Logic ................................... .164
DTC Confirmation Procedure .............................. .164
Wiring Diagram .................................................... .166
Diagnostic Procedure .......................................... .169
Component Inspection ......................................... .171
Removal and Installation ..................................... .171
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .172
Description ........................................................... .172
CONSULT-II Reference Value in Data Monitor Mode .172
On Board Diagnosis Logic ................................... .172
DTC Confirmation Procedure .............................. .173
Wiring Diagram .................................................... .174
Diagnostic Procedure .......................................... .177
Component Inspection ......................................... .179
Removal and Installation ..................................... .179
DTC P0075, P0081 IVT CONTROL SOLENOID
VALVE .................................................................... .180
Component Description ....................................... .180
CONSULT-II Reference Value in Data Monitor Mode .180
On Board Diagnosis Logic ................................... .180
DTC Confirmation Procedure .............................. .180
Wiring Diagram .................................................... .181 Diagnostic Procedure ...........................................
.185
Component Inspection ......................................... .186
Removal and Installation ...................................... .186
DTC P0101 MAF SENSOR .................................... .187
Component Description ....................................... .187
CONSULT-II Reference Value in Data Monitor Mode .187
On Board Diagnosis Logic ................................... .187
DTC Confirmation Procedure ............................... .188
Overall Function Check ........................................ .189
Wiring Diagram .................................................... .190
Diagnostic Procedure ........................................... .191
Component Inspection ......................................... .194
Removal and Installation ...................................... .195
DTC P0102, P0103 MAF SENSOR ........................ .196
Component Description ....................................... .196
CONSULT-II Reference Value in Data Monitor Mode .196
On Board Diagnosis Logic ................................... .196
DTC Confirmation Procedure ............................... .197
Wiring Diagram .................................................... .198
Diagnostic Procedure ........................................... .199
Component Inspection ......................................... .202
Removal and Installation ...................................... .203
DTC P0112, P0113 IAT SENSOR ........................... .204
Component Description ....................................... .204
On Board Diagnosis Logic ................................... .204
DTC Confirmation Procedure ............................... .204
Wiring Diagram .................................................... .206
Diagnostic Procedure ........................................... .207
Component Inspection ......................................... .208
Removal and Installation ...................................... .208
DTC P0117, P0118 ECT SENSOR ......................... .209
Component Description ....................................... .209
On Board Diagnosis Logic ................................... .209
DTC Confirmation Procedure ............................... .210
Wiring Diagram .................................................... .211
Diagnostic Procedure ........................................... .212
Component Inspection ......................................... .213
Removal and Installation ...................................... .213
DTC P0122, P0123 TP SENSOR ........................... .214
Component Description ....................................... .214
CONSULT-II Reference Value in Data Monitor Mode .214
On Board Diagnosis Logic ................................... .214
DTC Confirmation Procedure ............................... .215
Wiring Diagram .................................................... .216
Diagnostic Procedure ........................................... .217
Component Inspection ......................................... .220
Removal and Installation ...................................... .220
DTC P0125 ECT SENSOR ..................................... .221
Component Description ....................................... .221
On Board Diagnosis Logic ................................... .221
DTC Confirmation Procedure ............................... .222
Diagnostic Procedure ........................................... .222
Component Inspection ......................................... .223
Removal and Installation ...................................... .223
DTC P0127 IAT SENSOR ....................................... .224
Component Description ....................................... .224

EC-3
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2006 July 2007 FX35/FX45
On Board Diagnosis Logic ..................................
. 224
DTC Confirmation Procedure .............................. . 224
Diagnostic Procedure .......................................... . 225
Component Inspection ........................................ . 226
Removal and Installation ..................................... . 226
DTC P0128 THERMOSTAT FUNCTION ............... . 227
On Board Diagnosis Logic .................................. . 227
DTC Confirmation Procedure .............................. . 227
Diagnostic Procedure .......................................... . 227
Component Inspection ........................................ . 228
Removal and Installation ..................................... . 228
DTC P0130, P0150 A/F SENSOR 1 ...................... . 229
Component Description ....................................... . 229
CONSULT-II Reference Value in Data Monitor Mode . 229
On Board Diagnosis Logic .................................. . 229
DTC Confirmation Procedure .............................. . 229
Overall Function Check ....................................... . 231
Wiring Diagram ................................................... . 232
Diagnostic Procedure .......................................... . 235
Removal and Installation ..................................... . 238
DTC P0131, P0151 A/F SENSOR 1 ...................... . 239
Component Description ....................................... . 239
CONSULT-II Reference Value in Data Monitor Mode . 239
On Board Diagnosis Logic .................................. . 239
DTC Confirmation Procedure .............................. . 240
Wiring Diagram ................................................... . 241
Diagnostic Procedure .......................................... . 244
Removal and Installation ..................................... . 247
DTC P0132, P0152 A/F SENSOR 1 ...................... . 248
Component Description ....................................... . 248
CONSULT-II Reference Value in Data Monitor Mode . 248
On Board Diagnosis Logic .................................. . 248
DTC Confirmation Procedure .............................. . 249
Wiring Diagram ................................................... . 250
Diagnostic Procedure .......................................... . 253
Removal and Installation ..................................... . 256
DTC P0133, P0153 A/F SENSOR 1 ...................... . 257
Component Description ....................................... . 257
CONSULT-II Reference Value in Data Monitor Mode . 257
On Board Diagnosis Logic .................................. . 257
DTC Confirmation Procedure .............................. . 258
Wiring Diagram ................................................... . 260
Diagnostic Procedure .......................................... . 263
Removal and Installation ..................................... . 268
DTC P0137, P0157 HO2S2 ................................... . 269
Component Description ....................................... . 269
CONSULT-II Reference Value in Data Monitor Mode . 269
On Board Diagnosis Logic .................................. . 269
DTC Confirmation Procedure .............................. . 270
Overall Function Check ....................................... . 270
Wiring Diagram ................................................... . 272
Diagnostic Procedure .......................................... . 275
Component Inspection ........................................ . 277
Removal and Installation ..................................... . 279 DTC P0138, P0158 HO2S2 ....................................
.280
Component Description ....................................... .280
CONSULT-II Reference Value in Data Monitor Mode .280
On Board Diagnosis Logic ................................... .280
DTC Confirmation Procedure .............................. .281
Overall Function Check ....................................... .282
Wiring Diagram .................................................... .283
Diagnostic Procedure .......................................... .286
Component Inspection ......................................... .290
Removal and Installation ..................................... .292
DTC P0139, P0159 HO2S2 .................................... .293
Component Description ....................................... .293
CONSULT-II Reference Value in Data Monitor Mode .293
On Board Diagnosis Logic ................................... .293
DTC Confirmation Procedure .............................. .294
Overall Function Check ....................................... .294
Wiring Diagram .................................................... .296
Diagnostic Procedure .......................................... .299
Component Inspection ......................................... .301
Removal and Installation ..................................... .303
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .304
On Board Diagnosis Logic ................................... .304
DTC Confirmation Procedure .............................. .304
Wiring Diagram .................................................... .306
Diagnostic Procedure .......................................... .310
DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .316
On Board Diagnosis Logic ................................... .316
DTC Confirmation Procedure .............................. .316
Wiring Diagram .................................................... .318
Diagnostic Procedure .......................................... .322
DTC P0181 FTT SENSOR ..................................... .327
Component Description ....................................... .327
On Board Diagnosis Logic ................................... .327
DTC Confirmation Procedure .............................. .327
Wiring Diagram .................................................... .329
Diagnostic Procedure .......................................... .330
Component Inspection ......................................... .332
Removal and Installation ..................................... .332
DTC P0182, P0183 FTT SENSOR ......................... .333
Component Description ....................................... .333
On Board Diagnosis Logic ................................... .333
DTC Confirmation Procedure .............................. .333
Wiring Diagram .................................................... .334
Diagnostic Procedure .......................................... .335
Component Inspection ......................................... .337
Removal and Installation ..................................... .337
DTC P0222, P0223 TP SENSOR ........................... .338
Component Description ....................................... .338
CONSULT-II Reference Value in Data Monitor Mode .338
On Board Diagnosis Logic ................................... .338
DTC Confirmation Procedure .............................. .339
Wiring Diagram .................................................... .340
Diagnostic Procedure .......................................... .341

EC-4Revision: 2006 July 2007 FX35/FX45
Component Inspection .........................................
.344
Removal and Installation ..................................... .344
DTC P0300 - P0306 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 6 CYLINDER MISFIRE .................... .345
On Board Diagnosis Logic ................................... .345
DTC Confirmation Procedure .............................. .346
Diagnostic Procedure .......................................... .346
DTC P0327, P0328 KS ........................................... .355
Component Description ....................................... .355
On Board Diagnosis Logic ................................... .355
DTC Confirmation Procedure .............................. .355
Wiring Diagram .................................................... .356
Diagnostic Procedure .......................................... .357
Component Inspection ......................................... .358
Removal and Installation ..................................... .359
DTC P0335 CKP SENSOR (POS) ......................... .360
Component Description ....................................... .360
CONSULT-II Reference Value in Data Monitor Mode .360
On Board Diagnosis Logic ................................... .360
DTC Confirmation Procedure .............................. .361
Wiring Diagram .................................................... .362
Diagnostic Procedure .......................................... .363
Component Inspection ......................................... .366
Removal and Installation ..................................... .366
DTC P0340, P0345 CMP SENSOR (PHASE) ........ .367
Component Description ....................................... .367
CONSULT-II Reference Value in Data Monitor Mode .367
On Board Diagnosis Logic ................................... .367
DTC Confirmation Procedure .............................. .368
Wiring Diagram .................................................... .369
Diagnostic Procedure .......................................... .372
Component Inspection ......................................... .375
Removal and Installation ..................................... .375
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ....................................................................... .376
On Board Diagnosis Logic ................................... .376
DTC Confirmation Procedure .............................. .376
Overall Function Check ....................................... .377
Diagnostic Procedure .......................................... .378
DTC P0441 EVAP CONTROL SYSTEM ................ .382
System Description .............................................. .382
On Board Diagnosis Logic ................................... .382
DTC Confirmation Procedure .............................. .382
Overall Function Check ....................................... .383
Diagnostic Procedure .......................................... .384
DTC P0442 EVAP CONTROL SYSTEM ................ .387
On Board Diagnosis Logic ................................... .387
DTC Confirmation Procedure .............................. .388
Diagnostic Procedure .......................................... .389
DTC P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE .............................. .396
Description ........................................................... .396
CONSULT-II Reference Value in Data Monitor Mode .396
On Board Diagnosis Logic ................................... .397
DTC Confirmation Procedure .............................. .397
Wiring Diagram .................................................... .398 Diagnostic Procedure ...........................................
.400
Component Inspection ......................................... .403
Removal and Installation ...................................... .403
DTC P0444, P0445 EVAP CANISTER PURGE VOL-
UME CONTROL SOLENOID VALVE ..................... .404
Description ........................................................... .404
CONSULT-II Reference Value in Data Monitor Mode .404
On Board Diagnosis Logic ................................... .405
DTC Confirmation Procedure ............................... .405
Wiring Diagram .................................................... .406
Diagnostic Procedure ........................................... .408
Component Inspection ......................................... .409
Removal and Installation ...................................... .410
DTC P0447 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .411
Component Description ....................................... .411
CONSULT-II Reference Value in Data Monitor Mode .411
On Board Diagnosis Logic ................................... .411
DTC Confirmation Procedure ............................... .412
Wiring Diagram .................................................... .413
Diagnostic Procedure ........................................... .414
Component Inspection ......................................... .416
DTC P0448 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .418
Component Description ....................................... .418
CONSULT-II Reference Value in Data Monitor Mode .418
On Board Diagnosis Logic ................................... .418
DTC Confirmation Procedure ............................... .419
Wiring Diagram .................................................... .420
Diagnostic Procedure ........................................... .421
Component Inspection ......................................... .422
DTC P0451 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .424
Component Description ....................................... .424
CONSULT-II Reference Value in Data Monitor Mode .424
On Board Diagnosis Logic ................................... .424
DTC Confirmation Procedure ............................... .425
Diagnostic Procedure ........................................... .425
Component Inspection ......................................... .426
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .427
Component Description ....................................... .427
CONSULT-II Reference Value in Data Monitor Mode .427
On Board Diagnosis Logic ................................... .427
DTC Confirmation Procedure ............................... .428
Wiring Diagram .................................................... .429
Diagnostic Procedure ........................................... .430
Component Inspection ......................................... .432
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .433
Component Description ....................................... .433
CONSULT-II Reference Value in Data Monitor Mode .433
On Board Diagnosis Logic ................................... .433