2007 HUMMER H2 buttons

3. Press and hold the button you would like to
use to control the garage door until the
garage door moves. The indicator light, above
the selected button, should slowly blink.
You may need to hold the button from ve to
20 seconds.
4. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
5. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1 through 6, choosing
a different function button in Step 4 than what
you used for the garage door opener.
Using Universal Home Remote
Press and hold the appropriate button for at least
half of a second. The indicator light will come
on while the signal is being transmitted.
Reprogramming Universal Home
Remote Buttons
You can reprogram any of the three buttons by
repeating the instructions.
Erasing Universal Home Remote
Buttons
You should erase the programmed buttons when
you sell the vehicle or terminate your lease.
To erase either rolling code or xed code on the
Universal Home Remote device, do the following:
1. Press and hold the two outside buttons at
the same time for about 20 seconds, until
the indicator lights, located directly above the
buttons, begin to blink rapidly.
2. Once the indicator lights begin to blink,
release both buttons. The codes from all
button will be erased.
For additional information on Universal Home
Remote, seeCustomer Assistance Offices
on page 540.
155

Universal Home
Remote System Operation
(With One Triangular LED)
Your vehicle may have the Universal Home
Remote System. If there is one triangular Light
Emitting Diode (LED) above the Universal
Home Remote buttons, follow the instructions
below. If your vehicle has three round LED above
the Universal Home Remote buttons, follow the
instructions under Universal Home Remote System
Operation (with three round LED).
Do not use the Universal Home Remote with any
garage door opener that does not have the stop
and reverse feature. This includes any garage door
opener model manufactured before April 1, 1982.If you have a newer garage door opener with rolling
codes, please be sure to follow Steps 6 through 8 to
complete the programming of your Universal Home
Remote Transmitter.
Read the instructions completely before attempting
to program the Universal Home Remote. Because
of the steps involved, it may be helpful to have
another person available to assist you in the
programming steps.
Keep the original hand-held transmitter for use in
other vehicles as well as for future Universal Home
Remote programming. It is also recommended that
upon the sale of the vehicle, the programmed
Universal Home Remote buttons should be erased
for security purposes. See “Erasing Universal
Home Remote Buttons” later in this section or,
for assistance, seeCustomer Assistance Offices
on page 540.
Be sure that people and objects are clear of the
garage door or gate operator you are programming.
When programming a garage door, it is advised to
park outside of the garage.
It is recommended that a new battery be installed in
your hand-held transmitter for quicker and more
accurate transmission of the radio-frequency signal.
156

Programming Universal Home Remote
Follow these steps to program up to three channels:
1. Press and hold down the two outside
Universal Home Remote buttons, releasing
only when the Universal Home Remote
indicator light begins to ash, after
20 seconds. Do not hold down the buttons for
longer than 30 seconds and do not repeat
this step to program a second and/or
third hand-held transmitter to the remaining
two Universal Home Remote buttons.
2. Position the end of your hand-held transmitter
about 1 to 3 inches (3 to 8 cm) away from the
Universal Home Remote buttons while
keeping the indicator light in view.
3. Simultaneously press and hold both the
desired Universal Home Remote button
and the hand-held transmitter button. Do not
release the buttons until Step 4 has been
completed.
Some entry gates and garage door openers
may require you to substitute Step 3 with
the procedure noted in “Gate Operator and
Canadian Programming” later in this section.4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release
both buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for
two seconds and then turns to a constant
light, continue with Steps 6 through 8 following
to complete the programming of a rolling-code
device, most commonly, a garage door
opener.
157

6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release it.
Immediately press and hold the same button
a second time for two seconds, then
release it. Immediately, press and hold the
same button a third time for two seconds,
then release.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal
Home Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” Do
not repeat Step 1, as this will erase all previous
programming from the Universal Home Remote
buttons.Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds
of transmission. This may not be long enough
for Universal Home Remote to pick up the signal
during programming. Similarly, some U.S. gate
operators are manufactured to time out in
the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door
opener by using the “Programming Universal
Home Remote” procedures, regardless of where
you live, replace Step 3 under “Programming
Universal Home Remote” with the following:
Continue to press and hold the Universal Home
Remote button while you press and release every
two seconds (cycle) the hand-held transmitter
button until the frequency signal has been
successfully accepted by the Universal Home
Remote. The Universal Home Remote indicator
light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming
Universal Home Remote” to complete.
158

Using Universal Home Remote
Press and hold the appropriate Universal Home
Remote button for at least half of a second.
The indicator light will come on while the signal is
being transmitted.
Erasing Universal Home
Remote Buttons
To erase programming from the three Universal
Home Remote buttons do the following:
1. Press and hold down the two outside buttons
until the indicator light begins to ash, after
20 seconds. Do not hold the two outside
buttons for longer than 30 seconds.
2. Release both buttons.
The Universal Home Remote is now in the training
(learning) mode and can be programmed at any
time beginning with Step 2 under “Programming
Universal Home Remote” shown earlier in
this section.
Individual buttons cannot be erased, but they can
be reprogrammed. See “Reprogramming a
Single Universal Home Remote Button” following
this section.
Reprogramming a Single Universal
Home Remote Button
To program a device to Universal Home Remote
using a Universal Home Remote button
previously trained, follow these steps:
1. Press and hold the desired Universal Home
Remote button. Do not release the button.
2. The indicator light will begin to ash after
20 seconds. While still holding the Universal
Home Remote button, proceed with
Step 2 under “Programming Universal
Home Remote” shown earlier in this section.
For additional information on Universal Home
Remote, seeCustomer Assistance Offices
on page 540.
159

Storage Areas
Glove Box
Open the glove box by pulling the bottom of the
handle upward.
Center Overhead Console
Your vehicle is equipped with either a short or
long overhead console.
To open a door on the console, push on the rear
edge of the door and let it swing open. Push
the door up until it latches to close the door.
The overhead consoles also includes reading
lamps, the Universal Home Remote System
buttons and the sunroof switch (if equipped).
Center Console Storage Area
Your vehicle has a console compartment between
the bucket seats.
To open it, press the button on the side of the
console and swing the console lid open.
Luggage Carrier
If your vehicle has this feature, you can load cargo
on your vehicle.
The luggage carrier consists of siderails attached
to the roof. The crossrails attach into the
siderails and can be moved back and forth to
accommodate securing various cargo sizes.
Notice:Loading cargo on the luggage carrier
that weighs more than 300 lbs. (136 kg) or
hangs over the rear or sides of the vehicle may
damage your vehicle. Load cargo only on
top of the crossrails and tie the cargo down to
the crossrail support cargo tie-down loops,
making sure to fasten it securely.
Your vehicle may have a light bar, do not load
cargo on it. SeeOff-Road Lamps on page 190for
more information.
Do not exceed the maximum vehicle capacity
when loading your vehicle. For more information
on vehicle capacity and loading, seeLoading Your
Vehicle on page 362.
160

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 203.
B. Exterior Lamps Control. SeeExterior Lamps on
page 186.
C. Heated Windshield Washer Control
(If Equipped). SeeWindshield Washer on
page 181.
D. OnStar
®and Radio Steering Wheel Buttons.
SeeOnStar®System on page 144and
Audio Steering Wheel Controls on page 296.
E. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 205.
F. Locking Rear Axle and Full-Time Four-Wheel
Drive Buttons. SeeLocking Rear Axle on
page 311andFull-Time Four-Wheel Drive on
page 128.
G. Audio System. SeeAudio System(s) on
page 241.
H. Airbag Switch. SeeAirbag Off Switch on
page 84.
I. Glove Box. SeeGlove Box on page 160.J. Midgate Glass Up/Down Switch (SUT).
SeeMidgate
®(SUT) on page 105. Rear
Wiper/Washer Switch (SUV). SeeRear Window
Wiper/Washer (SUV) on page 182.
K. Dome Override Button. SeeDome Lamp
Override on page 191.
L. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 178.
M. Tilt Lever. SeeTilt Wheel on page 177.
N. Driver Information Center (DIC) Buttons. See
Driver Information Center (DIC) on page 222.
O. Parking Brake Release. SeeParking Brake
on page 133.
P. Traction Control Button. SeeTraction Control
System (TCS) on page 309.
Q. Tow/Haul Selector Button. See “Tow/Haul
Mode” underTowing a Trailer on page 374.
R. Ride Height Selector Button (If Equipped). See
Selectable Extended Rear Ride Height on
page 371.
175

S. Cigarette Lighter or Accessory Power Outlet
(If Equipped). SeeAshtray(s) and Cigarette
Lighter on page 197orAccessory Power
Outlet(s) on page 196.
T. Shift Lever. SeeAutomatic Transmission
Operation on page 124.
U. Accessory Power Outlets. SeeAccessory
Power Outlet(s) on page 196.
V. OnStar Buttons. SeeOnStar
®System on
page 144.
W. Rear Window Defogger Button. See “Rear
Window Defogger” underDual Automatic
Climate Control System on page 197.
X. Climate Control System. SeeDual Automatic
Climate Control System on page 197.
Hazard Warning Flashers
The hazard warning ashers warn others. They
also let police know you have a problem. Your front
and rear turn signal lamps will ash on and off.
The hazard warning
asher button is located
on top of the steering
column.
The hazard warning ashers work no matter what
ignition position the key is in, and even if the
key is not in the ignition.
Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
When the hazard warning ashers are on, your
turn signals will not work.
176