2007 FORD FIESTA engine

308-03-35 Manual Transmission/Transaxle 308-03-35
DISASSEMBLY
Transaxle(l6 11 8 8)
- Special Tool(s)
I Remover, Drive Pinion Seal I
15074
I I Separator, Oil Pan
Remover,
Differential Bearing
Cone
205-1 76 (1 5-074)
i
Mounting Stand
303-435 (21 -1 87)
Mounting Bracket,
EngineIDifferential
205-329 (1 5-1 05A)
Special Tool(s)
I I Installer, Extension Housing I
I I Remover, Input Shaft Fifth I
General Equipment
I Blanking plugs
1 Drift I
CAUTIONS:
Use vise protectors.
A Use a copper or plastic mallet to prevent
damage.
1. Using the special tools, mount the transaxle
on the mounting stand.
2. Clean any grease and foreign material from
the input shaft.
2006.0 Fiesta 1212006 G23118en
procarmanuals.com

308-03-62 Manual Transmission/'rransaxle 308-03-62
INSTALLATION
Transaxle - 1.25L Duratec-I 6V (Sigma)/Im4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V (Sigma)(l 6 1 14 0)
Special Tool(s)
Support Bar, Engine
303-290A (21
-1 40A)
Adapter for 303-290A 303-290-0
1 (2 1 -1 40-0 1 )
Adapter for 303-290A
303-290-02 (21
-1 40-02)
21 14002
I I I
General Equipment
Retaining strap
I Transmission jack I
Materials
Name Specification
Installation
Manual transmission
1 fluid
All vehicles
I. CAUTIONS:
WSD-M2C200-C
&se suitable retaining straps to secure
the transaxle on the transmission jack.
A~ake sure that the two locating dowels
are installed.
Using a suitable transmission jack, install
the transaxle.
2. Install the transaxle right-hand retaining
bolts.
3. Install the transaxle lower retaining bolts.
-- -- -
2006.0 Fiesta 1212006 GI 13293en
procarmanuals.com

308-03-63 Manual Transmission/Transaxle 308-03-63
INSTALLATION
4. Install the transaxle left-hand retaining bolt. Install the
engine rear mount.
5. Remove the retaining strap. 11. Remove the special tools.
6. Remove the transmission jack.
7. Install the engine and transaxle rear mount
retaining bracket.
12. N0TE:lnstall new exhaust flange nuts and
a new exhaust flange gasket.
Attach the exhaust flexible pipe to the
8. Lower the vehicle. catalytic
converter.
9. Using the special tools, raise the engine and
transaxle assembly.
10. N0TE:Do not tighten the engine rear mount
retaining nuts at this stage.
NOTE:
Install new engine rear mount retaining nuts.
2006.0 Fiesta 1212006 GI1 3293en
procarmanuals.com

308-03-65 Manual Transmission/Transaxle 308-03-65
INSTALLATION
ADO not damage the halfshaft oil seal. 21. Install the engine support insulator.
/ / AMake sure the snap ring is correctly
seated.
N0TE:lnstall a new snap ring.
Attach the left-hand halfshaft to the
transaxle.
20m ACAUTION:M~~~ sure that the heat shield
is installed to prevent damage to the ball
joint.
N0TE:The lower arm pinch bolt must be installed ' ' from the rear of the wheel knuckle.
22. Install the accessory drive belt cover.
Attach the lower arm to the wheel knuckle
on both sides.
Vehicles without automated gearshift
23. Attach the gearshift cables to the bracket
and turn the abutment sleeves
counterclockwise.
2006.0 Fiesta 1212006 GI 13293en
procarmanuals.com

308-03-67 Manual Transmission/Transaxle 308-03-67
INSTALLATION
Attach the starter motor electrical connector 34. Tighten the engine rear mount outer
/- . to the starter motor. retaining nuts. /'
31. Lower the vehicle. 35. Tighten the engine rear mount center
32. Tighten the strut spring assembly top retaining nut.
mount nuts on both sides.
36. Install the battery tray support bracket.
33. Install the transaxle upper retaining bolts.
Attach the engine wiring harness bracket to
the transaxle.
2006.0 Fiesta 1212006 GI1 3293en
procarmanuals.com

308=03=69 Manual Transmission/Transaxle 308=03=69
INSTALLATION
Transaxle - 2.OL Duratec-HE (M14)(16 11 4 0)
i
Special Tool(s)
I I Support Bar, Engine
Adapter for 303-290A
303-290-01 (21 -1 40-01
)
General Equipment , I
@ 21 14005
21 14006
I Retaining strap I
Adapter for 303-290A
303-290-05A (2 1
- 1 40-05A)
Adapter for 303-290A
303-290-06 (21 -1 40-06)
I Transmission jack I
Materials
Name Specification
Installation
1. CAUTIONS:
A~se suitable retaining straps to secure
the transaxle on the transmission jack.
A~ake sure that the two locating dowels
are installed.
Using a suitable transmission jack, install
the transaxle.
Manual transmission
1 fluid
2. Install the transaxle right-hand retaining
bolts.
WSD-M2C200-C
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

308-03-70 Manual Transmission/Transaxle 308-03-70
INSTALLATION
3. Install the transaxle lower retaining bolts. 9. Using the special tools, raise the engine and
transaxle assembly.
f
4. Install the transaxle left-hand retaining bolt.
10. N0TE:Do not tighten the engine rear mount
retaining nuts at this stage.
N0TE:lnstall new engine rear mount retaining nuts.
Install the engine rear mount.
5. Remove the retaining strap.
6. Remove the transmission jack.
7. Lower the vehicle.
8. Install the engine and transaxle rear mount
retaining bracket. 11. Remove the special tools.
12. N0TE:lnstall new exhaust flange nuts and ,
a new exhaust flange gasket.
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

308-03-71 Manual Transmission/Transaxle 308-03-71
INSTALLATION
Attach the exhaust flexible pipe to the 15.
Remove the support wrap or suitable splint
catalytic converter. from
the exhaust flexible pipe.
i
3m ACAUTION:~~ brake fluid is spilt on the 16. lnstall the right-hand halfshaft.
paintwork, the affected area must be For additional information,
refer to: Front
immediately washed down with cold water. Halfshaft
RH (205-04 Front Drive
N0TE:Make sure the spring clip is correctly seated. Halfshafts, Removal and Installation).
Connect the clutch slave cylinder supply
17. lnstall the left-hand halfshaft.
line. For additional information,
refer to: Front
lnstall the spring clip. Halfshaft LH (205-04 Front Drive
Halfshafts, Removal and Installation).
18. lnstall the engine support insulator.
14. Raise and support the vehicle. For
additional information, refer to: (I
00-02
Jacking and Lifting)
19. Install the accessory drive belt cover.
Jacking (Description and Operation),
Lifting (Description and Operation).
2006.0 Fiesta 1212006 G453417en
procarmanuals.com